Ricoh B230 Service Manual

 
SM 5-245 B230/B237 
Service 
Tables 
firmware update is done with the firmware files 
from the URL. 
086 Firmware Size Allows the service technician to confirm the size of 
the firmware data files during the firmware update 
execution. 
087  CERT: Macro Version Displays the macro version of the NRS 
certification. 
088  CERT: PAC Version  Displays the PAC version of the NRS certification. 
089  CERT: ID2 Code Displays ID2 for the NRS certification. Spaces are 
displayed as underscores (_). Asteriskes...

 
B230/B237 5-246  SM 
ƒ SP5816-161 
0: Japan, 1: USA, 2: Canada, 3: UK, 4: Germany, 5: France, 6: Italy,   
7: Netherlands, 8: Belgium, 9: Luxembourg, 10: Spain 
Line Type Authentication Judgment 
151 Touch [Execute]. 
Setting this SP classifies the telephone line where Cumin-M is connected as 
either dial-up or push type, so Cumin-M can automatically distinguish the 
number that connects to the outside line. 
ƒ  The current progress, success, or failure of this execution can be 
displayed with...

 
SM 5-247 B230/B237 
Service 
Tables 
0: Tone Dialing Phone 
1: Pulse Dialing Phone 
Inside Japan 2 may also be displayed: 
0: Tone Dialing Phone 
1: Pulse Dialing Phone 10PPS 
2: Pulse Dialing Phone 20PPS 
Outside Line/Outgoing Number 
154 The SP sets the number that switches to PSTN for the outside connection for 
Cumin-M in a system that employs a PBX (internal line). 
ƒ  If the execution of SP5816 151 has succeeded and Cumin-M has 
connected to the external line, this SP display is completely blank....

 
B230/B237 5-248  SM 
connected. This number is transmitted to and used by the Call Center to 
return calls. 
Limit: 24 numbers (numbers only) 
Connection Timing Adjustment: Incoming 
162 When the Call Center calls out to a Cumin-M modem, it sends a repeating ID 
tone (*#1#). This SP sets the line remains open to send these ID tones after 
the number of the Cumin-M modem is dialed up and connected.   
[0 to 24 / 1 / 1 /step] 
The actual amount of time is this setting x 2 sec. For example, if you set 2...

 
SM 5-249 B230/B237 
Service 
Tables 
Normally, it is best to allow unlimited time for certification and ID2 update 
requests, and for the notification that the certification has been completed. 
However, Cumin-M generates charges based on transmission time for the 
customer, so a limit is placed upon the time allowed for these transactions. 
If these transactions cannot be completed within the allowed time, do this SP 
to cancel the time restriction. 
175  Modem Modulation Mode Setting 
FAX TX Priority...

 
B230/B237 5-250  SM 
1: Inquiry number error 
2: Registration in progress 
3: Proxy error (proxy enabled) 
4: Proxy error (proxy disabled) 
5: Proxy error (Illegal user name or password) 
6: Communication error 
7: Certification update error 
8: Other error 
9: Inquiry executing 
Confirm Place 
205 Displays the result of the notification sent to the device from the GW URL in 
answer to the inquiry request. Displayed only when the result is registered at 
the GW URL. 
206 Register Execute  Executes...

 
SM 5-251 B230/B237 
Service 
Tables 
-11002  Chat execution error Parameter 
-11003 Unexpected error 
-12002 Inquiry, registration attempted without 
acquiring device status. 
-12003 Attempted registration without execution 
of an inquiry and no previous 
registration. 
Operation Error, 
Incorrect Setting 
-12004 Attempted setting with illegal entries for 
certification and ID2. 
-2385 Attempted dial up overseas without the 
correct international prefix for the 
telephone number. 
-2387  Not supported...

 
B230/B237 5-252  SM 
5821 [Remote Service Address]  
001  CSS-PI Device Code Sets the PI device code. After you change 
this setting, you must turn the machine off 
and on.   
[0 to 4 / 0 / 1 /step] 
002 RCG IP Address *CTL
Sets the IP address of the RCG (Remote 
Communication Gate) destination for call 
processing at the remote service center. 
 
[NV-RAM Data Upload] 
5824 Uploads the UP and SP mode data (except for counters and the serial 
number) from the NVRAM to an SD card. For details, see the...

 
SM 5-253 B230/B237 
Service 
Tables 
SP5-828-50 is set to 1. 
065 Job Spooling Enables/disables Job Spooling. 
[0 or 1 / 0 / 1 / step] 
0: Disabled, 1: Enabled 
066 Job Spooling Clear: 
Start  Ti m e Treatment of the job when a spooled job exists at 
power on. 
0: ON (Data is cleared) 
1: OFF (Automatically printed) 
069  Job Spooling (Protocol) Validates or invalidates the job spooling function 
for each protocol. 
0: Validates 
1: Invalidates 
bit0: LPR 
bit1: FTP 
bit2: IPP 
bit3: SMB 
bit4: BMLinkS...

 
B230/B237 5-254  SM 
147 Active IPv6 Stateless 
Address 1 
149 Active IPv6 Stateless 
Address 2 
151 Active IPv6 Stateless 
Address 3 
153 Active IPv6 Stateless 
Address 4 
155 Active IPv6 Stateless 
Address 5 These SPs are the IPv6 status addresses (1 to 5) 
referenced on the Ethernet or wireless LAN 
(802.11b) in the format:   
Status Address + Prefix Length 
The IPv6 address consists of a total 128 bits 
configured in 8 blocks of 16 bits each. 
156 IPv6 Manual Address This SP is the IPv6 manually...