Ricoh B230 Service Manual
Here you can view all the pages of manual Ricoh B230 Service Manual. The Ricoh manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 381
![Page 381
SM 5-15 B230/B237
Service
Tables
Stop Time * ENG
[5 to 30 / 10 / 1 sec/step]
003
Specifies the time for measuring the nip.
111 2 [Environmental Correction: Fusing]
Temp.: Threshold: Low *ENG
[10 to 23 / 17 / 1°C/step]
001
Specifies the threshold temperature for low temperature condition.
Temp.: Threshold: High *ENG
[24 to 40 / 30 / 1°C/step]
002
Specifies the threshold temperature for high temperature condition.
Low Temp. Correction *ENG
[0 to 15 / 5 / 1°C/step]
003 Specifies...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-380.png "Page 381
SM 5-15 B230/B237
Service
Tables
Stop Time * ENG
[5 to 30 / 10 / 1 sec/step]
003
Specifies the time for measuring the nip.
111 2 [Environmental Correction: Fusing]
Temp.: Threshold: Low *ENG
[10 to 23 / 17 / 1°C/step]
001
Specifies the threshold temperature for low temperature condition.
Temp.: Threshold: High *ENG
[24 to 40 / 30 / 1°C/step]
002
Specifies the threshold temperature for high temperature condition.
Low Temp. Correction *ENG
[0 to 15 / 5 / 1°C/step]
003 Specifies...")
SM 5-15 B230/B237 Service Tables Stop Time * ENG [5 to 30 / 10 / 1 sec/step] 003 Specifies the time for measuring the nip. 111 2 [Environmental Correction: Fusing] Temp.: Threshold: Low *ENG [10 to 23 / 17 / 1°C/step] 001 Specifies the threshold temperature for low temperature condition. Temp.: Threshold: High *ENG [24 to 40 / 30 / 1°C/step] 002 Specifies the threshold temperature for high temperature condition. Low Temp. Correction *ENG [0 to 15 / 5 / 1°C/step] 003 Specifies...
Page 382
![Page 382
B230/B237 5-16 SM
after the machine has recovered from the energy save mode, it returns to the
stand-by mode.
111 4 [First Print Correction]
Correction Temp. *ENG
[0 to 30 / 10 / 1°C/step]
001 Specifies the additional temperature for the first print job.
This temperature is added to the heating roller for the time specified with
SP1114-002.
Operation Time *ENG
[0 to 60 / 2 / 1 sec/step]
002
Specifies the time for adding the first print additional temperature, which is
specified with...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-381.png "Page 382
B230/B237 5-16 SM
after the machine has recovered from the energy save mode, it returns to the
stand-by mode.
111 4 [First Print Correction]
Correction Temp. *ENG
[0 to 30 / 10 / 1°C/step]
001 Specifies the additional temperature for the first print job.
This temperature is added to the heating roller for the time specified with
SP1114-002.
Operation Time *ENG
[0 to 60 / 2 / 1 sec/step]
002
Specifies the time for adding the first print additional temperature, which is
specified with...")
B230/B237 5-16 SM after the machine has recovered from the energy save mode, it returns to the stand-by mode. 111 4 [First Print Correction] Correction Temp. *ENG [0 to 30 / 10 / 1°C/step] 001 Specifies the additional temperature for the first print job. This temperature is added to the heating roller for the time specified with SP1114-002. Operation Time *ENG [0 to 60 / 2 / 1 sec/step] 002 Specifies the time for adding the first print additional temperature, which is specified with...
Page 383
![Page 383
SM 5-17 B230/B237
Service
Tables
003 Idling Speed *ENG
[0 to 3 / 1 / 1 mm/sec /step] Not used
111 6 [Ends Temp. Correction]
Center Temp. 1: 226– *ENG
[–30 to 0 / 0 / 1°C/step]
010 Specifies the temperature correction for the heating roller (center) when the
paper width is 226 mm or more.
The start time of this SP can be adjusted with SP1116-018.
Ends Temp. 1: 226– *ENG
[–30 to 0 / 0 / 1°C/step]
011 Specifies the temperature correction for the heating roller (ends) when the
paper width...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-382.png "Page 383
SM 5-17 B230/B237
Service
Tables
003 Idling Speed *ENG
[0 to 3 / 1 / 1 mm/sec /step] Not used
111 6 [Ends Temp. Correction]
Center Temp. 1: 226– *ENG
[–30 to 0 / 0 / 1°C/step]
010 Specifies the temperature correction for the heating roller (center) when the
paper width is 226 mm or more.
The start time of this SP can be adjusted with SP1116-018.
Ends Temp. 1: 226– *ENG
[–30 to 0 / 0 / 1°C/step]
011 Specifies the temperature correction for the heating roller (ends) when the
paper width...")
SM 5-17 B230/B237 Service Tables 003 Idling Speed *ENG [0 to 3 / 1 / 1 mm/sec /step] Not used 111 6 [Ends Temp. Correction] Center Temp. 1: 226– *ENG [–30 to 0 / 0 / 1°C/step] 010 Specifies the temperature correction for the heating roller (center) when the paper width is 226 mm or more. The start time of this SP can be adjusted with SP1116-018. Ends Temp. 1: 226– *ENG [–30 to 0 / 0 / 1°C/step] 011 Specifies the temperature correction for the heating roller (ends) when the paper width...
Page 384
![Page 384
B230/B237 5-18 SM
Specifies the temperature correction for the heating roller (center) when the
paper width is less than 226 mm.
The start time of this SP can be adjusted with SP1116-021.
Ends Temp. 4: –226 *ENG
[–30 to 0 / –10 / 1°C/step]
017 Specifies the temperature correction for the heating roller (ends) when the
paper width is less than 226 mm.
The start time of this SP can be adjusted with SP1116-021.
Control Time 1: 226– *ENG
[0 to 250 / 0 / 1 sec/step]
018 Specifies the start...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-383.png "Page 384
B230/B237 5-18 SM
Specifies the temperature correction for the heating roller (center) when the
paper width is less than 226 mm.
The start time of this SP can be adjusted with SP1116-021.
Ends Temp. 4: –226 *ENG
[–30 to 0 / –10 / 1°C/step]
017 Specifies the temperature correction for the heating roller (ends) when the
paper width is less than 226 mm.
The start time of this SP can be adjusted with SP1116-021.
Control Time 1: 226– *ENG
[0 to 250 / 0 / 1 sec/step]
018 Specifies the start...")
B230/B237 5-18 SM Specifies the temperature correction for the heating roller (center) when the paper width is less than 226 mm. The start time of this SP can be adjusted with SP1116-021. Ends Temp. 4: –226 *ENG [–30 to 0 / –10 / 1°C/step] 017 Specifies the temperature correction for the heating roller (ends) when the paper width is less than 226 mm. The start time of this SP can be adjusted with SP1116-021. Control Time 1: 226– *ENG [0 to 250 / 0 / 1 sec/step] 018 Specifies the start...
Page 385
![Page 385
SM 5-19 B230/B237
Service
Tables
Specifies the temperature correction for the heating roller (center) when the
paper width is 226 mm or more in duplex mode.
The start time of this SP can be adjusted with SP1116-026.
Ends Temp. 1 Duplex:
226– *ENG
[–30 to 0 / 0 / 1°C/step]
023
Specifies the temperature correction for the heating roller (ends) when the
paper width is 226 mm or more in duplex mode.
The start time of this SP can be adjusted with SP1116-026.
Center Temp. 2 Duplex:
226– *ENG...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-384.png "Page 385
SM 5-19 B230/B237
Service
Tables
Specifies the temperature correction for the heating roller (center) when the
paper width is 226 mm or more in duplex mode.
The start time of this SP can be adjusted with SP1116-026.
Ends Temp. 1 Duplex:
226– *ENG
[–30 to 0 / 0 / 1°C/step]
023
Specifies the temperature correction for the heating roller (ends) when the
paper width is 226 mm or more in duplex mode.
The start time of this SP can be adjusted with SP1116-026.
Center Temp. 2 Duplex:
226– *ENG...")
SM 5-19 B230/B237 Service Tables Specifies the temperature correction for the heating roller (center) when the paper width is 226 mm or more in duplex mode. The start time of this SP can be adjusted with SP1116-026. Ends Temp. 1 Duplex: 226– *ENG [–30 to 0 / 0 / 1°C/step] 023 Specifies the temperature correction for the heating roller (ends) when the paper width is 226 mm or more in duplex mode. The start time of this SP can be adjusted with SP1116-026. Center Temp. 2 Duplex: 226– *ENG...
Page 386
![Page 386
B230/B237 5-20 SM
111 7 [Idling Time After Heater OFF]
After Ready *ENG
[0 to10 / 4 / 1 sec/step] DFU
001
Specifies the idling time without the lamp on after reaching the ready
temperature.
After Job End *ENG
[0 to10 / 4 / 1 sec/step]
002
Specifies the idling time without the lamp on after job end.
This idling prevents the heating roller overheating after job end.
11 5 9 [Fusing Jam Detection]
SC Display *ENG[0 or 1 / 0 / 1 /step]
0: Disable, 1: Enable
001
Enables or disables...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-385.png "Page 386
B230/B237 5-20 SM
111 7 [Idling Time After Heater OFF]
After Ready *ENG
[0 to10 / 4 / 1 sec/step] DFU
001
Specifies the idling time without the lamp on after reaching the ready
temperature.
After Job End *ENG
[0 to10 / 4 / 1 sec/step]
002
Specifies the idling time without the lamp on after job end.
This idling prevents the heating roller overheating after job end.
11 5 9 [Fusing Jam Detection]
SC Display *ENG[0 or 1 / 0 / 1 /step]
0: Disable, 1: Enable
001
Enables or disables...")
B230/B237 5-20 SM 111 7 [Idling Time After Heater OFF] After Ready *ENG [0 to10 / 4 / 1 sec/step] DFU 001 Specifies the idling time without the lamp on after reaching the ready temperature. After Job End *ENG [0 to10 / 4 / 1 sec/step] 002 Specifies the idling time without the lamp on after job end. This idling prevents the heating roller overheating after job end. 11 5 9 [Fusing Jam Detection] SC Display *ENG[0 or 1 / 0 / 1 /step] 0: Disable, 1: Enable 001 Enables or disables...
Page 387
![Page 387
SM 5-21 B230/B237
Service
Tables
010 MCY Development: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
011 MCY Development: 138 *ENG
[–4 to 4 / 0 / 0.01 %/step]
012 MCY Development: 77 *ENG
[–4 to 4 / 0 / 0.01 %/step]
013 Fusing: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
014 Fusing: 138 *ENG
015 Fusing: 77 *ENG[–4 to 4 / 0.4 / 0.01 %/step]
016 Image Transfer: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
017 Image Transfer: 138 *ENG
[–4 to 4 / 0.3 / 0.01 %/step]
018 Image...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-386.png "Page 387
SM 5-21 B230/B237
Service
Tables
010 MCY Development: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
011 MCY Development: 138 *ENG
[–4 to 4 / 0 / 0.01 %/step]
012 MCY Development: 77 *ENG
[–4 to 4 / 0 / 0.01 %/step]
013 Fusing: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
014 Fusing: 138 *ENG
015 Fusing: 77 *ENG[–4 to 4 / 0.4 / 0.01 %/step]
016 Image Transfer: 154 *ENG
[–4 to 4 / 0 / 0.01 %/step] Not used
017 Image Transfer: 138 *ENG
[–4 to 4 / 0.3 / 0.01 %/step]
018 Image...")
SM 5-21 B230/B237 Service Tables 010 MCY Development: 154 *ENG [–4 to 4 / 0 / 0.01 %/step] Not used 011 MCY Development: 138 *ENG [–4 to 4 / 0 / 0.01 %/step] 012 MCY Development: 77 *ENG [–4 to 4 / 0 / 0.01 %/step] 013 Fusing: 154 *ENG [–4 to 4 / 0 / 0.01 %/step] Not used 014 Fusing: 138 *ENG 015 Fusing: 77 *ENG[–4 to 4 / 0.4 / 0.01 %/step] 016 Image Transfer: 154 *ENG [–4 to 4 / 0 / 0.01 %/step] Not used 017 Image Transfer: 138 *ENG [–4 to 4 / 0.3 / 0.01 %/step] 018 Image...
Page 388
![Page 388
B230/B237 5-22 SM
Counterclockwise
1907 [Paper Feed Timing Adj.] DFU
003 Feed Clutch OFF: Plain *ENG
[–10 to 10 / 0 / 1 mm/step]
004 Feed Clutch ON: Plain *ENG
[–10 to 10 / 0 / 1 mm/step]
005 Inverter Stop Position *ENG
[–10 to 10 / 0 / 1 mm/step]
006 Exit Stop Position: 3rd
Sheet *ENG
[–10 to 10 / 0 / 1 mm/step]
011 Entrance Stop Position *ENG
[–7 to 10 / 0 / 1 mm/step]
013 Feed Clutch OFF: Thick *ENG
[–10 to 10 / 0 / 1 mm/step]
014 Feed Clutch ON: Thick *ENG
[–10 to 10 / 0 /...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-387.png "Page 388
B230/B237 5-22 SM
Counterclockwise
1907 [Paper Feed Timing Adj.] DFU
003 Feed Clutch OFF: Plain *ENG
[–10 to 10 / 0 / 1 mm/step]
004 Feed Clutch ON: Plain *ENG
[–10 to 10 / 0 / 1 mm/step]
005 Inverter Stop Position *ENG
[–10 to 10 / 0 / 1 mm/step]
006 Exit Stop Position: 3rd
Sheet *ENG
[–10 to 10 / 0 / 1 mm/step]
011 Entrance Stop Position *ENG
[–7 to 10 / 0 / 1 mm/step]
013 Feed Clutch OFF: Thick *ENG
[–10 to 10 / 0 / 1 mm/step]
014 Feed Clutch ON: Thick *ENG
[–10 to 10 / 0 /...")
B230/B237 5-22 SM Counterclockwise 1907 [Paper Feed Timing Adj.] DFU 003 Feed Clutch OFF: Plain *ENG [–10 to 10 / 0 / 1 mm/step] 004 Feed Clutch ON: Plain *ENG [–10 to 10 / 0 / 1 mm/step] 005 Inverter Stop Position *ENG [–10 to 10 / 0 / 1 mm/step] 006 Exit Stop Position: 3rd Sheet *ENG [–10 to 10 / 0 / 1 mm/step] 011 Entrance Stop Position *ENG [–7 to 10 / 0 / 1 mm/step] 013 Feed Clutch OFF: Thick *ENG [–10 to 10 / 0 / 1 mm/step] 014 Feed Clutch ON: Thick *ENG [–10 to 10 / 0 /...
Page 389
![Page 389
SM 5-23 B230/B237
Service
Tables
007 Feed Clutch ON: Thick *ENG
[–10 to 10 / 0 / 1 mm/step]
SP2-XXX (Drum)
2005 [Charge DC Voltage] Charge Roller DC Voltage Adjustment
(Paper Type, Process Speed, Color)
Paper Type –> Plain, Thick 1, Thick 2
Adjusts the DC component of the charge roller bias in the various print modes.
Charge bias (DC component) is automatically adjusted during process control;
therefore, adjusting these settings does not effect while process control mode
(SP3-041-1...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-388.png "Page 389
SM 5-23 B230/B237
Service
Tables
007 Feed Clutch ON: Thick *ENG
[–10 to 10 / 0 / 1 mm/step]
SP2-XXX (Drum)
2005 [Charge DC Voltage] Charge Roller DC Voltage Adjustment
(Paper Type, Process Speed, Color)
Paper Type –> Plain, Thick 1, Thick 2
Adjusts the DC component of the charge roller bias in the various print modes.
Charge bias (DC component) is automatically adjusted during process control;
therefore, adjusting these settings does not effect while process control mode
(SP3-041-1...")
SM 5-23 B230/B237 Service Tables 007 Feed Clutch ON: Thick *ENG [–10 to 10 / 0 / 1 mm/step] SP2-XXX (Drum) 2005 [Charge DC Voltage] Charge Roller DC Voltage Adjustment (Paper Type, Process Speed, Color) Paper Type –> Plain, Thick 1, Thick 2 Adjusts the DC component of the charge roller bias in the various print modes. Charge bias (DC component) is automatically adjusted during process control; therefore, adjusting these settings does not effect while process control mode (SP3-041-1...
Page 390
![Page 390
B230/B237 5-24 SM
Charge bias (AC component) is adjusted by environment correction
(SP2-007-xxx to SP2-011-xxx). These SPs are activated only when SP2-012-1
is set to 1: manual control.
001 Plain: Bk *ENG
002 Plain: M *ENG
003 Plain: C *ENG
004 Plain: Y *ENG
005 Thick 1: Bk *ENG
006 Thick 1: M *ENG
007 Thick 1: C *ENG
008 Thick 1: Y *ENG
009 Thick 2&FINE: Bk *ENG
010 Thick 2&FINE: M *ENG
011 Thick 2&FINE: C *ENG
012 Thick 2&FINE: Y *ENG[0 to 3000 / 2100 / 10 V/step]
[Charge AC...](http://img.usermanuals.tech/thumb/64/100811/w300_b230-service-manual-1509630901_d-389.png "Page 390
B230/B237 5-24 SM
Charge bias (AC component) is adjusted by environment correction
(SP2-007-xxx to SP2-011-xxx). These SPs are activated only when SP2-012-1
is set to 1: manual control.
001 Plain: Bk *ENG
002 Plain: M *ENG
003 Plain: C *ENG
004 Plain: Y *ENG
005 Thick 1: Bk *ENG
006 Thick 1: M *ENG
007 Thick 1: C *ENG
008 Thick 1: Y *ENG
009 Thick 2&FINE: Bk *ENG
010 Thick 2&FINE: M *ENG
011 Thick 2&FINE: C *ENG
012 Thick 2&FINE: Y *ENG[0 to 3000 / 2100 / 10 V/step]
[Charge AC...")
B230/B237 5-24 SM Charge bias (AC component) is adjusted by environment correction (SP2-007-xxx to SP2-011-xxx). These SPs are activated only when SP2-012-1 is set to 1: manual control. 001 Plain: Bk *ENG 002 Plain: M *ENG 003 Plain: C *ENG 004 Plain: Y *ENG 005 Thick 1: Bk *ENG 006 Thick 1: M *ENG 007 Thick 1: C *ENG 008 Thick 1: Y *ENG 009 Thick 2&FINE: Bk *ENG 010 Thick 2&FINE: M *ENG 011 Thick 2&FINE: C *ENG 012 Thick 2&FINE: Y *ENG[0 to 3000 / 2100 / 10 V/step] [Charge AC...