Ricoh B230 Service Manual

  
SM 1-69 B230/B237 
Installation 
1.  Press the “User Tools/Counter” key. 
2.  On the touch panel, press “System Settings”. 
3.  Press “Interface Settings”. 
4. Press “IEEE1394”. 
5.  Press the following soft keys on the touch panel. Then set up the following 
settings: 
ƒ  “IP Address”: Set the IP Address and Subnet Mask. 
ƒ  “IP over 1394”: Enable or disable this setting as required. This setting enables IP 
over 1394 as the default setting for the printing method. 
ƒ  “SCSI Print”: Enable or disable...

 
B230/B237 1-70  SM 
1.20.6 IEEE1284 
Installation Procedure 
 
ƒ Unplug the main machine power cord before you do the following 
procedure. 
You can only install one of the following network interfaces at a time: (IEEE 802.11b 
(Wireless LAN), IEEE1284, Bluetooth). 
 
1.  Remove the slot cover [A] from I/F Card Slot B (
 x 2). 
2.  Install the interface board [B] (Knob-screw x 2) into I/F card slot B. 
3.  Make sure that the machine can recognize the option (see ‘Check All 
Connections’ at the end of...

  
SM 1-71 B230/B237 
Installation 
1.20.7  IEEE 802.11B (WIRELESS LAN) 
Installation Procedure 
 
ƒ Unplug the main machine power cord before you do the following 
procedure. 
You can only install one of the following network interfaces at a time: (IEEE 802.11b 
(Wireless LAN), IEEE1284, Bluetooth). 
 
1.  Remove the slot cover [A] from I/F Card Slot B (
 x 2). 
2.  Install the wireless LAN board (Knob-screw x 2) into I/F card slot B. 
3.  Install the wireless LAN card [B] in the wireless LAN board [C]....

 
B230/B237 1-72  SM 
1.  Press the “User Tools/Counter” key. 
2.  On the touch panel, press “System Settings”. 
 
ƒ  The Network I/F (default: Ethernet) must be set for either Ethernet or wireless 
LAN.  
3.  Select “Interface Settings” 
 “Network” (tab)  “Network I/F Setting” 
4.  Press “IEEE 802.11b”. Only the wireless LAN options show. 
5.  Communication Mode. Select either “802.11 Ad hoc”, “Ad hoc” or 
“Infrastructure”. 
6.  SSID Setting. Enter the SSID setting. (The setting is case sensitive.) 
7....

  
SM 1-73 B230/B237 
Installation 
Press “Yes” to initialize the following settings: 
ƒ Transmission mode 
ƒ Channel 
ƒ Transmission Speed 
ƒ WEP 
ƒ SSID 
ƒ WEP Key 
SP Mode Settings for IEEE 802.11b Wireless LAN 
The following SP commands and UP modes can be set for IEEE 802.11b   
SP No.  Name  Function 
5840 006  Channel MAX Sets the maximum range of the channel settings for the 
country. 
5840 007  Channel MIN Sets the minimum range of the channels settings 
allowed for your country. 
5840 011  WEP...

 
B230/B237 1-74  SM 
1.20.8 BLUETOOTH 
 
ƒ Unplug the main machine power cord before you do the following 
procedure. 
You can only install one of the following network interfaces at a time: (IEEE 802.11b 
(Wireless LAN), IEEE1284, Bluetooth). 
 
1.  Remove the slot cover [A] from I/F Card Slot B [A] (
 x 2). 
2.  Install the Bluetooth board [B] (Knob-screw x 2) into I/F card slot B. 
3.  Insert the Bluetooth card [C] into the Bluetooth card adaptor [D]. . 
4.  Attach the antenna cap [E] to the...

  
SM 1-75 B230/B237 
Installation 
1.20.9  COPY DATA SECURITY UNIT 
 
ƒ Unplug the main machine power cord before you do the following 
procedure. 
 
ƒ  If you install this option, you cannot use scanner or fax functions. 
 
1.  Remove the rear cover [A] of the machine (
x 7). 
 
1.  Loosen the eight screws.   
2.  Slide up the controller box cover [B], and then remove it. 
3.  Attach the ICIB-2 (copy data security board) [C] to CN 504 on the BICU (
 x 2). 
4.  Reassemble the machine.  

 
B230/B237 1-76  SM 
Installing Setting 
1.  Plug in and turn on the main power switch. 
2.  Go into the User Tools mode, and select System Settings > Administrator Tools 
> Copy Data Security Option > On. 
3.  Exit the User Tools. 
4.  Check the operation. 
 
ƒ  The machine will issue an SC165 error if the machine is powered on with the 
ICIB-2 removed and the Data Security for Copying feature set to ON. 
5.  Make sure that the machine can recognize the option (see ‘Check All 
Connections’ at the end...

  
SM 1-77 B230/B237 
Installation 
Seal Check and Removal 
 
 
ƒ You must check the box seals to make sure that they were not removed after 
the items were sealed in the box at the factory before you do the installation. 
1.  Check the box seals [A] on each corner of the box. 
ƒ  Make sure that a tape is attached to each corner. 
ƒ  The surfaces of the tapes must be blank. If you see “VOID” on the tapes, do not 
install the components in the box. 
2.  If the surfaces of the tapes do not show “VOID”,...

 
B230/B237 1-78  SM 
Installation Procedure 
 
ƒ Unplug the main machine power cord before you do the following 
procedure. 
 
ƒ  You must install the data overwrite security unit in SD Card slot 2. However, the 
Postscript option and the PictBridge option are also installed in SD Card slot 2. 
You must do the SD Card Appli move procedure first if you have the postscript or 
PictBridge option installed and you want to install the data overwrite security unit.   
 
1.  Turn off the main power switch if...