Ricoh B230 Service Manual

  
SM 1-79 B230/B237 
Installation 
 
 
Diagnostic Report: “ROM No. / Firmware 
Version” [A] “Loading Program” [B] 
Data Overwrite Security 
Unit  HDD Format Option: 
B7355060 / 0.03 GW2a_zoffy: 
B7355060 / 0.03 
 
ƒ  The ROM number and firmware version number change when the firmware is 
upgraded. However, the important thing is to make sure the numbers in [A] are 
the same as the numbers in [B]. 
ƒ  If the ROM numbers are not the same, or the version numbers are not the same, 
this means the unit was...

 
B230/B237 1-80  SM 
1.20.11 USB HOST INTERFACE 
 
ƒ Unplug the main machine power cord before you do the following 
procedure. 
 
1.  If the IEEE1394 unit is installed in I/F Card Slot A, remove it. 
2.  Remove the slot cover [A] from I/F Card Slot A (
 x 2). 
3.  Install the USB Host Interface [B] (Knob-screw x 2) into I/F card slot A. 
4.  Make sure that the machine can recognize the option (see ‘Check All 
Connections’ at the end of this section).  

  
SM 1-81 B230/B237 
Installation 
1.20.12 PICTBRIDGE 
 
ƒ Unplug the main machine power cord before you do the following 
procedure. 
 
ƒ  You must install the PictBridge option in SD Card slot 2. However, the Postscript 
option and the data overwrite security unit option are also installed in SD Card slot 
2. You must do the SD Card Appli move procedure first if you have the postscript 
or data overwrite security unit option installed and you want to install the 
PictBridge unit. 
ƒ  You must install...

 
B230/B237 1-82  SM 
1.20.13 BROWSER UNIT TYPE B 
 
ƒ Unplug the main machine power cord before you do the following 
procedure. 
SD card slot 3 is basically used only for service maintenance. Do not leave an SD card in 
slot 3 after installing an application. 
 
1.  Remove the slot cover [A] from SD card slot 3 (
 x 1). 
2.  Turn the SD-card [B] label face to the rear of the machine. Then push it slowly 
into slot 3 until you hear a click. 
3.  Plug in and turn on the main power switch. 
4.  Push the...

  
SM 1-83 B230/B237 
Installation 
18. Touch OK. 
19.  Touch Exit twice to go back to the copy screen. 
20.  Turn off the main power switch. 
21.  Remove the SD card from slot 3. 
22.  Attach the slot cover [A] (
x 1). 
1.20.14 CHECK  ALL CONNECTIONS 
1.  Plug in the power cord. Then turn on the main switch. 
2.  Enter the printer user mode. Then print the configuration page. 
User Tools > Printer Settings > List Test Print > Config. Page 
All installed options are shown in the “System Reference”...

 
 
 
 
 
 
PREVENTIVE MAINTENANCE 
  

 
SM 2-1 B230 
Preventive 
Maintenance 
2. PREVENTIVE  MAINTENANCE 
2.1 SETTINGS 
2.1.1 BEFORE REMOVING THE OLD PM PARTS 
1.  Enter the SP mode. 
2.  Output the SMC logging data with SP5-990-004. 
3.  Set the following SPs to 1 before you turn the power off. Then, the machine 
will reset the PM counters automatically. In the case of developer, the developer 
initialization will also be done automatically. 
4.  Exit the SP mode. 
Item SP 
Developer Black: 3902-005 
Yellow: 3902-006 
Cyan: 3902-007...

 
B230/B237 2-2  SM 
ƒ  Toner Collection Bottle (if full or near-full) 
2.1.2 AFTER INSTALLING THE NEW PM PARTS 
1.  Turn on the main power switch.   
2.  Output the SMC logging data with SP5-990-004 and check the counter values. 
3.  Make sure that the PM counters for the replaced units are “0” with SP7-803. If the 
PM counter for a unit was not reset, then reset that counter with SP 7-904. 
4.  Make sure that the exchange counter counts up with SP7-853. 
5.  Make sure that the counters for the previous...