Ricoh B230 Service Manual

Bit Switches 
SM 51 B786 
B786 
Fax Option 2 Automatic error report printout 
0: Disabled 1: Enabled 0: Error reports will not be printed. 
1: Error reports will be printed automatically after 
failed communications. 
3 Printing of the error code on 
the error report 
0: No 1: Yes 1: Error codes are printed on the error reports. 
4 Not used  Do not change this setting. 
5 Power failure report 
0: Disabled 1: Enabled 1: A power failure report will be automatically 
printed after the power is switched on...

Bit Switches 
B786 52  SM 
System Switch 0C - Not used (Do not change the factory settings.) 
System Switch 0D - Not used (Do not change the factory settings.) 
 
System Switch 0E [SP No. 1-101-015] 
No FUNCTION COMMENTS 
0-1 Not used  Do not change the settings. 
2 Enable/disable for direct 
sending selection 
0: Direct sending off  
1: Direct sending on Direct sending cannot operate when the capture 
function is on during sending. Setting this switch 
to 1 enables direct sending without capture....

Bit Switches 
SM 53 B786 
B786 
Fax Option 
0A: Sweden   1A: China 
0B: Switzerland  1B: Formosa 
0C: Portugal   1C: Korea 
0D: Netherland   20: Turkey 
0E: Spain   21: Greece 
0F: Israel  22: Hungary 
10: ---  23: Czech 
11: USA  24: Poland   
 
System Switch 10 [SP No. 1-101-017] 
No FUNCTION COMMENTS 
0-7 Threshold memory level for 
parallel memory transmission Threshold = N x 128 KB + 256 KB 
N can be between 00 - FF(H) 
Default setting: 02(H) = 512 KB 
 
System Switch 11 [SP No. 1-101-018] 
No...

Bit Switches 
B786 54  SM 
the TTI from the left edge of the paper. If the TTI 
is moved too far to the right, it may overwrite the 
file number which is on the top right of the page. 
On an A4 page, if the TTI is moved over by more 
than 50 mm, it may overwrite the page number. 
 
System Switch 13 - Not used (do not change these settings) 
System Switch 14 - Not used (do not change these settings) 
 
System Switch 15 [SP No. 1-101-022] 
No FUNCTION COMMENTS 
0 Not used  Do not change the settings. 
1...

Bit Switches 
SM 55 B786 
B786 
Fax Option 
 
System Switch 17 - Not used (do not change these settings) 
System Switch 18 - Not used (do not change these settings) 
 
System Switch 19 [SP No. 1-101-026] 
No FUNCTION COMMENTS 
0-5 Not used  Do not change the settings. 
6 Extended scanner page 
memory after memory option 
is installed 
0: Disabled 
1: Enabled 0: After installing the memory expansion option, the 
scanner page memory is extended to 4 MB from 2 
MB.  
1: If this bit is set to 1 after...

Bit Switches 
B786 56  SM 
2 Destination telephone 
number display limitation 
0: OFF, 1: ON  When 1 is selected, the destination telephone 
number display is limited and redial is disabled. 
3 Operation selection without 
PIN code registered 
0: Transmission interrupted 
1: No interrupted 
transmission  0: When 0 is selected without PIN code 
registration, transmission is interrupted and an alert 
message shows on the LCD. 
4-7 Not used  Do not change these settings. 
 
System Switch 1E [SP No....

Bit Switches 
SM 57 B786 
B786 
Fax Option 
the sender has an RTI or CSI  block messages from senders that do not include 
an RTI or CSI, change this bit to “1”, then enable 
Authorized Reception. 
Otherwise, keep this bit at “0 (default setting)”. 
5-7 Not used  Do not change the settings 
 
System Switch 1F [SP No. 1-101-032] 
No FUNCTION COMMENTS 
0 Not used  Do not change the settings. 
1 Report printout after an 
original jam during SAF 
storage or if the SAF memory 
fills up 
0: Enabled 
1:...

Bit Switches 
B786 58  SM 
3-6 Reserved 
7 Not used is “A3” (Bit 2). 
When mail is sent, there is no negotiation with the 
receiving machine at the destination, so the 
sending machine cannot make a selection for the 
receiving capabilities (original width setting) of the 
receiving machine. The original width selected 
with this switch is used as the RX machine’s 
original width setting, and the original is reduced 
to this size before sending. The default is A4. 
If the width selected with this switch...

Bit Switches 
SM 59 B786 
B786 
Fax Option 
I-fax Switch 02 [SP No. 1-102-003] 
No FUNCTION COMMENTS 
RX Text Mail Header Processing 
0 This setting determines whether the header information is printed with text e-mails 
when they are received. 
0: Prints only text mail. 
1: Prints mail header information attached to text mail. 
When a text mail is received with this switch On (1), the “From” address and 
“Subject” address are printed as header information. 
When a mail with only binary data is received...

Bit Switches 
B786 60  SM 
5-6 Not Used 
Image Resolution of RX Text Mail 
7 This setting determines the image resolution of the received mail. 
0: 200 x 200 
1: 400 x 400 
The “1” setting requires installation of the Function Upgrade Card in order to have 
enough SAF (Store and Forward) memory to receive images at 400 x 400 
resolution. 
 
I-fax Switch 03 - Not used (do not change the settings) [ SP No. 1-102-004] 
 
I-fax Switch 04 [SP No. 1-102-005] 
No FUNCTION COMMENTS 
Subject for Delivery...