Projector Christie Roadster S+20k User Manual

OPERATION 
  Roadster/Mirage S+ User’s Manual 3-73 
Table 3.4. System Error Codes  
Code Description GENERAL 12  Software error. Contact dealer/factory. 13  CRC error in flash ROM. Download new software. 14  Engineering-only programming is complete. Call Christie, replace TIPM. 15  Attempting to download s/w code without being in boot mode 16  Invalid interrupt. Power off/on. If persists, contact dealer/factory. 17  User has forced system to stay in boot mode 18  Attempting to program boot mode without...

Section 4 
Maintenance 
 
 Roadster/Mirage S+ User’s Manual 4-1 
 
This projector is safety agency approved and is designed for safe and reliable 
operation. However, safe operation cannot be assured by design alone; installers, 
maintainers, and users must maintain a safe operating environment for the system. 
Please read through and understand the following warnings and guidelines promoting 
safe usage of the projector. 
 WARNING  
Always remove the lens when shipping the projector. 
 WARNING  
NEVER...

MAINTENANCE 
4-2 
Roadster/Mirage S+ User’s Manual 
A projector and cart combination should be used with care. Sudden stops, excessive 
force, and uneven surfaces may cause the projector and cart combination to overturn.  
LAMP: Do not operate the Bubble lamp for more than the lamp’s warranty limit; risk 
of the lamp shattering increases as a result of changes in the quartz glass that occur 
with use. Operation beyond the lamp’s warranty limit also significantly reduces 
brightness output. 
 WARNING...

MAINTENANCE 
  Roadster/Mirage S+ User’s Manual 4-3 

MAINTENANCE 
4-4 
Roadster/Mirage S+ User’s Manual 
 WARNING  
Always power down and unplug the projector before 
cleaning or servicing. 
Table 4.1. Maintenance Guide 
Part Description Frequency Action 
Lens  As required 
CLEAN: Clean if absolutely necessary. A 
small amount of dust on the lens has very 
little affect on picture quality. 
To clean: Apply a solvent such as acetone, 
alcohol or vinegar sparingly to clean, lint-
free lens tissue. Wipe across the surface of 
the lens. Do not scrub or rub...

MAINTENANCE 
  Roadster/Mirage S+ User’s Manual 4-5 
 
The IR Remote Keypad uses two AA size, 1.5V batteries (preferably alkaline). To 
install new batteries:  
1) Open the battery 
compartment at the 
backside of the keypad by 
placing your thumb in the 
oval depression and sliding 
the cover out about ½ inch. 
See Figure 4.1. Remove the 
old batteries and properly 
discard. Wait a minute or 
two.  
2) Place the new batteries in the 
compartment, orienting the 
positive/negative of each battery...

MAINTENANCE 
4-6 
Roadster/Mirage S+ User’s Manual 
How old is the lamp? 
The number of hours logged on the current lamp appears both in the Lamp menu and 
the Status menu. In the Status menu, do not confuse “Lamp Hours” with “Lamp 
Counter” which indicates the number of hours logged during the current rental period 
only and is normally used for rental projectors only. 
NOTE: As the lamp nears its limit (as set in Lamp Limit), a message can appear on 
screen to warn that the lamp needs to be replaced....

MAINTENANCE 
  Roadster/Mirage S+ User’s Manual 4-7 
3.  OPEN THE LAMP DOOR 
   WARNING  
Protective gear required. Wear a 
face shield. 
Using a #2 Phillips screwdriver, 
loosen the ¼-turn lock screws (2) 
securing the lamp door, which is 
located at the rear of the projector 
below the input panel. See Figure 
4.2. 
4. REMOVE LAMP 
RETAINING BAR 
Remove the two (2) screws that secure the retaining bar along the bottom edge of 
the lamp module using a #2 Phillips screwdriver. See Figure 4.3. Swing the...

MAINTENANCE 
4-8 
Roadster/Mirage S+ User’s Manual 
6.  INSERT THE NEW LAMP MODULE 
Align the base plate of the new lamp module under both side alignment guides 
(see right). Slide the 
module fully into the 
projector in the same 
orientation you removed 
the old lamp module. Push 
with normal force until the 
resistance increases, then 
firmly push module 
another ½ inch.  
NOTE: The lamp module 
must make full contact
 
with the lamp connectors. Increased resistance when sliding the module in...