Projector Christie Roadster S+20k User Manual

OPERATION 
  Roadster/Mirage S+ User’s Manual 3-33 
 
Figure 3.16. Adjusting Input Levels Using the Peak Detector 
(RED EXAMPLE SHOWN) 
 
Advanced Image Settings 
— SUBMENU 
Use the Advanced Image 
Settings submenu to make the 
adjustments necessary for lesser 
used but more specialized 
applications on your projector. 
 
 
 
 
GAMMA TABLE: This control applies a default video, graphics or simple gamma table 
or “curve” to your images, controlling the intensity of midlevel colors and producing 
maximum...

OPERATION 
3-34 
Roadster/Mirage S+ User’s Manual 
Different values (1-3) here indicate that the original gamma table has been adjusted 
with either the Gamma slide bar or direct key. 
SELECT COLOR ADJUSTMENT: In “Select Color 
Adjustment”, choose an overall color palette for all images. 
The “Max Drives” factory default simply drives all 3 colors 
at their maximum level so that they are fully on and cannot 
be changed. The two other pre-defined color adjustment 
choices—SD Video and HD Video—apply a...

OPERATION 
  Roadster/Mirage S+ User’s Manual 3-35 
Simulation 3D — SUBMENU OF ADVANCED IMAGE SETTINGS 
Use the options in the Simulation 3D 
menu to make the timing adjustments 
necessary for realistic simulation and 
3D images. Figure 3.17. 
NOTES: 1) Available in Mirage 
projectors only. 2) For complete 3D 
application notes, refer to the separate 
Using 3D in Mirage
 manual provided 
with the Mirage projector. 
FRAME DELAY MONITOR — This slidebar monitors the latency between input and 
output. For...

OPERATION 
3-36 
Roadster/Mirage S+ User’s Manual 
  
With your sync cable, Z-screen and, if desired, emitter connected as described in the 
Using 3D in Mirage
 manual, select the option suited to your 3D configuration (see 
above). If Frame Delay is 2 (or 0), do not invert; if frame delay is 1 or 3, invert. 
Generally, an “Unlocked” setting is synchronized with the incoming L/R signal 
rather than the vertical sync output, and may be needed only with multi-projector 
installations in which the vertical...

OPERATION 
  Roadster/Mirage S+ User’s Manual 3-37 
1. AUTO: The projector will automatically use the correct motion filter 
according to the incoming signal. 
2. 
STILL: For static images with no motion, such as graphics from a CD. 
3. 
MOTION: For video images that did not originate from film, or for moving 
computer-generated images. 
4. 
FILM: For video images that originated from film. This will optimize image 
quality and stability. 
FILM MODE THRESHOLD —  This setting determines how sensitively...

OPERATION 
3-38 
Roadster/Mirage S+ User’s Manual 
Image Orientation 
Set the orientation of the image according to the orientation of your projector. If the 
setting is incorrect, projected images will be reversed and/or upside down. 
Reserved 
No function. 
Auto Power-up 
Enter a checkmark to enable the projector to automatically power up after losing 
power due to a power failure or due to unplugging the projector during operation. 
Note that unsaved display adjustments may be lost. 
Set Date & Time...

OPERATION 
  Roadster/Mirage S+ User’s Manual 3-39 
accessed, but will be hidden during adjustment. This option does not affect slidebars 
in menus. 
DISPLAY ERROR MESSAGES — Choose how you want to be notified of errors 
detected in either the incoming signal or projector.
 Select “Screen” or “All” (default) 
to see brief on-screen messages. This is particularly recommended during setup or 
testing of the projector. Or select “Serial Ports” to receive messages via RS232 or 
RS422 serial communication...

OPERATION 
3-40 
Roadster/Mirage S+ User’s Manual 
NOTE: When multiple projectors are being used and you want to adjust the color 
and edge blending settings for individual projectors to create one seamless image, 
you must assign different numbers for each projector to allow toggling back and 
forth between projectors while adjustments are being made.  
Network Routing 
NOTE: Not applicable for stand-alone projectors or simple serial networks with only 
one type of controller and linking. 
 
SEPARATE:...

OPERATION 
  Roadster/Mirage S+ User’s Manual 3-41 
DHCP: Enable this checkbox if you want a DHCP server to automatically change the 
projector’s default IP address (0.0.0.0) to one that is valid and unique for use on the 
current Ethernet network. On networks without a DHCP server, or to simply override 
the automatic DHCP server function, delete the checkmark and enter the new “IP 
Address” settings desired. Remember that only a 0.0.0.0 address will trigger the 
DHCP addressing service, and only when...

OPERATION 
3-42 
Roadster/Mirage S+ User’s Manual 
ArtNet BASE CHANNEL: When advanced mode is enabled, the projector listens to data 
on 64 consecutive channels, or 10 consecutive channels when advanced mode is not 
enabled. The projector processes requests that come on either 10 or 64 consecutive 
channels beginning with the ‘base channel’ defined here. The requests implement the 
following functions:  
* Functions are only active when the Slider Lock is set to Unlocked 
† Lens functions have no effect...