Projector Christie Roadster S+20k User Manual

							Roadster/Mirage S+ Users Manual  
 
Table of Contents 
 
013-100190-03 (06/06) Software v1.2d  Roadster/Mirage S+ User’s Manual i  
Section Contents Page 
1.1 The Projectors................................................................................................... 1-1 
1.2 Components ...................................................................................................... 1-2 
1.3  Purchase Record and Warranty Registration .................................................... 1-3 
 
2.1 Quick Setup ...................................................................................................... 2-1 
2.2 Installation Considerations ............................................................................... 2-3 
2.3  Projector Position and Mounting .................................................................... 2-15 
2.4 Source Connections ........................................................................................ 2-18 
2.5 Connecting Communications.......................................................................... 2-21 
2.6  Connecting Multiple Projectors ...................................................................... 2-24 
2.7 Power Connection .......................................................................................... 2-27 
2.8 Operating Orientation ..................................................................................... 2-28 
2.9 Leveling .......................................................................................................... 2-28 
2.10  Zoom, Focus, and Lens Offset........................................................................ 2-29 
2.11 Keypad Protocols and Conversion ................................................................. 2-29 
 
3.1 Overview .......................................................................................................... 3-1 
3.2 Projector Basics ................................................................................................ 3-1 
3.3  Using the Keypads............................................................................................ 3-4 
3.4  Navigating the Menus..................................................................................... 3-12 
3.5  Using Inputs and Channels ............................................................................. 3-16 
3.6  Adjusting the Image........................................................................................ 3-21 
3.7  Adjusting System Parameters and Advanced Controls .................................. 3-37 
3.8  Working with PIP or Seamless Switching ...................................................... 3-51 
3.9  Working with the Lamp.................................................................................. 3-54 
3.10 Status Menu .................................................................................................... 3-58 
3.11  Using Multiple Projectors............................................................................... 3-58 
3.12  Remote Control of the Projector ..................................................................... 3-70 
3.13 Error Conditions ............................................................................................. 3-71 
 
4.1  Warnings and Guidelines ................................................................................. 4-1 
4.2 Cleaning............................................................................................................ 4-4 
4.3 Replacing Keypad Batteries ............................................................................. 4-5 
4.4  Replacing the Lamp and Filter ......................................................................... 4-5 
4.5  Replacing the Lens ......................................................................................... 4-11 
 
5.1 Displays ............................................................................................................ 5-1 
5.2 Lamp ................................................................................................................. 5-3 
5.3 Ethernet............................................................................................................. 5-4 
6.1 Specifications ................................................................................................... 6-1 
 
 
 
 
continued… 
1 Introduction
 
2  Installation & 
Setup 
3  Basic 
Operation 
4  Maintenance 
5  Troubleshooting 
6 Specifications
  
						

							TABLE OF CONTENTS 
ii 
Roadster/Mirage S+ User’s Manual          013-100190-03 (06/06) Software v1.2d  
   
 
 
A   Glossary ........................................................................................................... A-1 
B   Remote Keypad ............................................................................................... B-1 
C   Serial Communication Cables.......................................................................... C-1 
D   Throw Distance................................................................................................ D-1 
E   System Integration ........................................................................................... E-1 
F    Optional Input Modules ................................................................................... F-1 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 NOTE: Due to continuing research, all information in this manual is subject to change without notice. 
 Appendices
  
						

							Section 1 
Introduction 
 
 Roadster/Mirage S+ User’s Manual 1-1 
The Roadster S+ and Mirage S+14K projectors are innovative, high brightness 
DMD™ projectors that use next generation Digital Light Processing™ (DLP™) 
technology from Texas Instruments. All 
models feature compact size, rugged 
construction, and integral rigging 
hardware, with the Roadster Series ideal 
for difficult rental/staging installations of 
multiple projectors, and the Mirage S
+ 
Series featuring amazing stereo 3D 
output. A quick-change lamp module, 
no-tool lens replacement, and intuitive 
user interface means the ultimate in 
versatility and ease-of-use. These 
projectors provide brilliant images with 
1400 x 1050 clarity and perfect color 
saturation in a wide variety of applications. 
The Roadster S
+ Series and Mirage S+ Series each have features for your distinct 
needs. The stereoscopic Mirage S+ projector provides 3D solutions for power walls, 
simulation, and entertainment venues. Roadster models include an additional input 
module as well as integral hardware for stacking and flying up to 3 projectors. 
General 

						

							INTRODUCTION 
1-2 
Roadster/Mirage S+ User’s Manual 

						

							INTRODUCTION 
 
Roadster/Mirage S+ User’s Manual 1-3 
Whether the projector is under warranty or the warranty has expired, Christie’s 
highly trained and extensive factory and dealer service network is always available to 
quickly diagnose and correct projector malfunctions. Complete service manuals and 
updates are available to service technicians for all projectors. 
Should you encounter a problem with the projector and require assistance, contact 
your dealer or Christie. In many cases, any necessary servicing can be performed on 
site. If you have purchased the projector, fill out the Purchase Record below and keep 
with your records. In addition, make sure to complete the Product Registration at the 
Christie website—this will ensure that you receive all future product communications 
promptly. 
Purchase Record 
Dealer:  
Dealer Phone Number:   
Projector Serial Number @  :  
Purchase Date:   
Installation Date, if applicable:   
@  NOTE: The projector serial number is located on the projector’s rear identification label 
and in the projector’s “Status” menu. 
1.3 Purchase 
Record and 
Warranty 
Registration  
						

							Section 2 
Installation & Setup 
 
 Roadster/Mirage S+ User’s Manual 2-1 
This section explains how to install and set up the projector. If you are familiar with the projector and want to quickly 
set it up for temporary use, follow the Quick Setup instructions below. For a more complete setup, follow the 
instructions and guides covered in the remaining subsections. 
NOTE: The lens is not installed for shipping. Refer to 4.5, Replacing the Lens. 
Follow these steps for quick setup of the projector in a standard floor mount position. 
Use either the remote or built-in keypad to work with the projected image. 
Position the Projector 
Set the projector at the expected throw distance (projector-to-screen distance) and 
vertical position. See 2.3, Projector Position and Mounting and Appendix D. Make 
sure that the projector is level from side-to-side (see Section 2.9, Leveling). 
Connect a Source 
Locate the main input panel at the rear of the projector and connector your source to 
the appropriate input:  
◊ INPUT 1 (upper right area) – RGB input via BNC connectors.  
◊ INPUT 2 (left of BNCs) – digital or analog signals (DVI-I) from a computer. 
◊ INPUT 3 (upper middle area) – composite video.  
◊ INPUT 4 (upper middle area) – S-video. 
◊ INPUT 5 (lower area of Roadster panel) – a factory-installed Dual SD/HD-SDI 
module that can accept serial digital. 
◊ INPUT 6 (lower area) – for optional input modules (see Appendix F).  
Connect to Power 
  The North American rated line cord is provided with each projector. Ensure 
that you are using a line cord that meets the appropriate rating standards (CCC 
for use in China, PSE for use in Japan).
 
Connect the projector’s line cord to the AC receptacle* at the lower rear corner on 
the rear of the projector, and to proper AC—note the socket outlet must be installed 
near the equipment and is easily accessible. Use only the line cord provided with the 
projector. Power requirements are shown below, with complete information in Section 6. 
  
*NOTE: The Roadster S+20K has an integral line cord. 
 
 
2.1 Quick Setup 
 STEP 1 '
 STEP 2 '
 STEP 3 ' 
						

							INSTALLATION & SETUP 
2-2 
Roadster/Mirage S+ User’s Manual 
◊ The Roadster S+12K requires 200-240 VAC, 50-60 Hz, 12 amps @ 200 VAC. 
◊ The Roadster S+16K and the Mirage S+14K require 200-240 VAC, 50-60 Hz, 16 
amps @ 200 VAC. 
◊ The Roadster S
+ 20K requires 200-240 VAC, 50-60 Hz, 24 amps @ 200 VAC. 
 WARNING  
Do not attempt operation if the AC supply and cord are not 
within the specified voltage and power range. See Section 6. 
Turn On the Projector and Lamp  
1.  On the projector, turn the power 
breaker/switch on. The LCD Status 
Display Window displays the 
initializing window for 15 seconds, 
then indicates 
POWER OFF (see 
right). 
2.  Using the keypad, do one of the 
following:  
• Press and hold 
 briefly to 
toggle the lamp on. 
• Press and release 
 followed 
immediately by 
.  
• Press 
  to toggle from the 
off state.  
The LCD Status Display Window 
will display Powering Up and 
then, Power On (Figure 2.1) while 
the 2 Digit Status/Error Code 
Window will display ON. 
Select a Source 
Using either keypad, press 
Inpu t  1, Inpu t  2,
 Inpu t  3,
 Inpu t  4,
 Inpu t  5, or Inpu t  6 to select and display 
the image for the source you connected in Step 2. The display will resize as needed, 
producing an image as large as possible for the type of source present. 
Optimize the Display 
Press 
Au t o
Se t u p on the built-in keypad (or  on the remote keypad) to initiate an 
automated process in which the projector optimizes critical display parameters such as 
size, position, pixel tracking, etc., for the current source. Auto Setup can save time in 
perfecting a display, and you can modify the adjustments later as desired. See Section 3.   STEP 4 '
 
Figure 2.1. Turning on the projector 
 STEP 5 '
 STEP 6 ' 
						

							INSTALLATION & SETUP 
  Roadster/Mirage S+ User’s Manual 2-3 
 
Lens Adjustments 
NOTE: Not applicable to fixed lenses. Focus fixed lens by turning focus 
ring on lens. 
• 
ZOOM: With the input image displayed: 
o If remote keypad: Press Zoom 
 or .
 
o If built-in keypad: Press Zoom 
 or .
 
Hold the key down to see the effect –arrows in the display indicate the direction 
of the zoom (Figure 2.2). 
• 
FOCUS: With the input image displayed: 
o If remote keypad: Press Focus 
 or .
 
o If built-in keypad: Press Focus
 
 or .
 
Hold the key down to see the effect – arrows in the display indicate 
the direction of the focus (Figure 2.3). 
• 
• LENS OFFSET: To move the image: 
o 
If remote keypad: Press either Lens H
 or 
Lens V 
 (Figure 2.4). 
o If built-in keypad: Press 
Len s
Sh i f t and use the arrow 
keys. 
 
Image Adjustments 
Press 
Menu or  (remote) to access display parameters 
described in Section 3. 
. 
Although this projector delivers a high brightness, quality output, final display 
quality could be compromised if the projector is not properly installed. This 
subsection discusses issues you should consider before proceeding with a final 
installation. Even if you do not intend to use the projectors in a fixed and permanent 
installation, the following information will help you to better understand what you 
can do to enhance display performance  
For any new installation, you will likely have to safely lift or hoist the projector into 
place. Keep in mind the following guidelines for safety. 
Lifting 
All models include handles for convenient hand transport only
, such as when a 
projector is lifted from a shipping container to a table. Note the following:  
◊ The handles are intended to support the weight of one
 projector only. 
◊ The handles are intended to support a projector for a brief
 time only. 
◊ The handles are not
 safety points, nor points from which to hoist or suspend 
the projector.   STEP 7 '
 
Figure 
2.2 
 
Figure 
2.3 
 
 
 
Figure 2.4 
 Step 8 '
2.2 Installation 
Considerations 
 Lifting, Hoisting, '
   and Stackin
g  
						

							INSTALLATION & SETUP 
2-4 
Roadster/Mirage S+ User’s Manual 
 WARNINGS  
• The handles can’t support more than 1 projector. 
• Do not
 use handles for extended time periods. 
• Do not
 use the handles as safety points, or as points 
from which to suspend or hoist the projector. 
Hoisting 
Four integral rigging points on the top of the projector (Figure 2.5) and eight on the 
bottom (Figure 2.6) enable either upright or inverted hoisting. For either orientation, 
hoist an individual projector, or up to 3 projectors in a stack. 
 
Figure 2.5. Top Rigging Points 
RULES FOR ALL HOISTING: 
◊ Use at least 4 rigging points for hoisting up 
to 3
 projectors.  
◊ Connect safety cables, and rigging 
equipment to the designated locations on 
the projector. 
◊ Use hoisting and rigging equipment suitable 
to your application such as clamps, cables, 
eyebolts, or straps, and which accommodate 
the load rating. All integral, metric 
hardware on the projector accepts an M12 
thread only. 
◊ Never hoist a projector by its feet, handles, 
or any other component (Figure 2.7). 
 
 
 
Figure 2.6. Bottom Rigging 
Points