Projectiondesign F3+ Sxga+ Projector User Manual

italianonorsk
51

H position      50
V position       50
color temp      
 6500   7300   9300   custom
custom colo
r
custom brightness       press
custom contrast       press
video format  
 auto     NTSC     PAL   SECAM
video type                   
 DVD                      VCR

color temp      6500   7300   9300   custom
custom color
custom brightness       press
custom contrast       press

H position      50
V position       50
Phase        
4
frequenc
y     1688
color temp     6500  
 7300   9300...

englishdeutschfrancaisespa
ñol
52

SET UP SUB MENU
keystone VAdjust  vertical    keystone  correction.  Compensates  for  the  geometrical distortion of the projected image resulting from tilting the projector to shoot higher up on the wall. 
keystone HAdjust  horizontal  keystone  correction.  Compensates  for  the  geometrical distortion  of  the  projected  image  resulting  from  shooting  the  image  at  an angle sideways to the screen. 
IR controlActivate  and  deactivate  the  IR  sensors  used...

italianonorsk
53

IR front enable disable
IR back (lef
t)  enable   disable
IR back (right)  enable
 disable

keystone V                0
ke ystone H                
0
IR control        press 
 
DPMS        on 
 off
source scan       
 on   off
orientation     
 desktop  front
OS
D
language
RGB  Video     
 off

SOTTOMENU SET UP (CONFIGURAZIONE)
keystone V (trapezio V)Consente  di  correggere  l’effetto  trapezio  verticale.  Compensa  la deformazione  geometrica  che  si  produce  quando  il...

englishdeutschfrancaisespa
ñol
54

UTILITIES SUB MENU
system informationDisplays information about the source and projector status.
OSDTurn the On Screen Display on (display) or off (hide) during source scan. 
OSD timeoutDefines how long OSD is displayed after last key action before it disappears from the screen.
OSD backgroundSelect background mode, whether transparent or opaque.
resetResets the projector to its basic settings. All parameters available in the various menus are reset to their factory...

italianonorsk
55

 
 
  source:  YPbPr       brightness: 60
fo rmat :  480p NTSC  contrast:
 50
mode:
  51      color :  40
sof tware:
 F3 301.35  sharpness: 3
white boost:
  10  gamma: film 1
RC-ID  0 
color temp:  6500K
lamp 1:     lamp 2:
- runtime:
  0 hrs  - runtime: 0 hrs
- remaining:
  1999 hrs  - remaining: 1999 hrs
- powe r:  1 00%  - power:   100  
%
lens mounted: standard (1.7-2.5  : 1)
MA C:
   
IP address: LAN is not sele cted  projector port:
subnet: LAN is not sele cted  X-Po rt 1 po rt:...

englishdeutschfrancaisespa
ñol
56

CONTROL SUB MENU
modeSelects between RS232 and X-PORT control modes. 
RS232 addressFor use when daisy-chaining several units. Select auto or fixed address. Only one address scheme is allowed per daisy-chain. The auto address is allocated following the relative position in the daisy-chain. The fixed address is an absolute address. Only unique fixed addresses are allowed.
RS232 fixedSelect a unique fixed address in the range available.
baudrateSelects between baudrates 4800,...

italianonorsk
57

MENU SECONDARIO CONTROL (CONTROLLO)
mode (modalità)Consente di selezionare tra le modalità di controllo RS232 e X-PORT. 
RS232 address (Indirizzo RS232)Da  utilizzarsi  quando  si  collegano  a  catena  più  unità.  Selezionare l’indirizzo  automatico  o  fisso.  È  consentito  un  solo  schema  di  indirizzi  per collegamento a catena. L’indirizzo automatico viene assegnato in base alla posizione relativa nel collegamento a catena. L’indirizzo fisso è un indirizzo assoluto. Sono...

englishdeutschfrancais
58

RS 232
You may control and monitor the projector remotely through the serial RS232 control interface.
Two RS232 protocols are employed. A simple instruction set (SIS) ASCII  protocol gives access to the most frequently used commands. In addition, a binary protocol is available where each command is a series of 32 bytes in one packet. The protocols allow for both SET and GET operations. To utilize GET operations the host needs a routine for receiving and interpreting incoming...

espa
ñol
italianonorsk
59

RS 232
Puede controlar y supervisar el proyector a distancia a través de la interfaz de control serie RS232.
Se  utilizan  dos  protocolos  RS232.  Un  juego  de  instrucciones  sencillas  del  protocolo  ASCII  le  da acceso  a  los  comandos  utilizados  con  más  frecuencia.  Además,  dispone  de  un  protocolo  binario en  el  que  cada  comando  es  una  serie  de  32  bytes  en  un  paquete.  Los  protocolos  permiten  las operaciones  SET  y  GET.  Para  utilizar  las...

englishdeutschfrancais
60

NO IMAGE
No connection: Check if all connections  are properly made. 
Source off: Check if the equipment is powered on.
Lamp dead: The lamp may need replacement. Check the LAMP TIME in the UTILITIES sub menu.
Source hibernated: Engage the source to display and activate image.
Notebook  external  screen:  Different  notebook  PC’s  use  different  combinations  of  keystrokes  to enable the external graphics port.
Source scan off: Check SOURCE SCAN in the SET UP sub menu. If...