Pioneer Kuro Pro Fpj1 Projector User Manual

31
ENGLISH
Getting Started Preparation Basic OperationSettingsTroubleshooting Others
zThis can also be displayed from the remote control. (pP10)
zThis can also be displayed from the remote control. (pP10)
Info. (During video signal input)
kInput
Displays the currently selected video input.
lFormat
Displays the types of the current input video signals.
mH Frequency
This item is grayed out with no value display.
nV Frequency
This item is grayed out with no value display.
oLamp Hours
Displays the...

32
4Settings
Customizing Projected Images 
“Contrast”, “Brightness”, “Color”, “Sharpness”, “DNR”, “Color Temp.”, “Gamma” and 
“Offset” are registered in the AV Selection.
ASelect the AV Selection
BAdjust image quality
Example: To adjust “Contrast”
aDisplay the setting menu
bSelect “Picture” g “Picture Adjust” g “Contrast”
cAdjust the setting
dTo end the adjustments
COther items can also be adjusted
DTo end
You can adjust the projected image to a desired image quality and register the adjusted value. (AV...

33
ENGLISH
Getting Started Preparation Basic OperationSettingsTroubleshooting Others
ASelect the AV Selection
BAdjust image quality
CTo end
AAdjust image quality
BDisplay the setting menu
CSelect “Setup” g “User Setting” g “Save 
User1”
DRegister the setting
Registering User-defined AV Selection
zSee “Changing the Default AV Selection Values” for procedures on 
adjusting the image quality. (pP32)
Registering User-defined AV Selection from 
the Menu
zSee “Changing the Default AV Selection Values” for...

5
34
Troubleshooting
Troubleshooting
Before sending the unit to your authorized dealer for repair, check the following points.
The following situations are not malfunctions.
„
You do not need to worry under the following situations if there is no abnormality on the screen.
zPart of the top surface or front of the unit is hot.
zA creaking sound is heard from the unit.
zAn operating sound is heard from the internal of the unit.
zColor smear occurs on some screens.
„Perform the following operations when the...

35
ENGLISH
Getting Started Preparation Basic Operation SettingsTroubleshootingOthers
Video image is fuzzy
Is the focus correctly adjusted?Adjust the focus.pP19
Is the unit placed too near or too far away 
from the screen?Set the unit at a correct distance from the screen.pP16, 17
Video images are missing
Has setting been performed for screen 
mask?Set “Screen Crop” in the setting menu to “Off”.pP21, 26-O
Is the display out of position?Alter the “Picture Position” value in the setting menu to ensure 
that...

5
36
Troubleshooting
What to Do When These Messages 
Are Displayed
MessageCause (Details)
No device is connected to the input terminal.
The input terminal is connected but there is no signal.
gInput the video signals.
A video signal that cannot be used in this unit has been input.
gInput video signals that can be used.
The message is displayed when the accumulated lamp time has exceeded 
1900 hours.
To clear the message, press the [EXIT] button.
gGet ready a new lamp unit and replace as soon as...

37
ENGLISH
Getting Started Preparation Basic Operation SettingsTroubleshootingOthers
About Warning Indicators
The accumulated lamp time or warning mode of this unit is displayed by the indicators.
For information on indicator display during normal operation, see “Controls and Features” (pP8).
When the unit enters into warning mode (No. 3 to 10), it will automatically stop projection and run the cooling fan for 
about 60 seconds.
After the cooling fan has stopped, pull out the power plug from the power...

38
5Troubleshooting
Replacing the Lamp
ARemove the lamp cover
BLoosen the screws on the lamp unit
CPull out the lamp unit
The lamp is a consumable item. If the image is dark or the lamp is turned off, replace the lamp unit. 
z
When the lamp replacement time approaches, a message is displayed on the screen and the condition is indicated by the 
indicator. (pP36, 37)
Procedure for Lamp Replacement
zRemove the screws with a + screwdriver.
zLoosen the screws with a + screwdriver.
zGrasp the handle and pull...

39
ENGLISH
Getting Started Preparation Basic Operation SettingsTroubleshootingOthers
DInstall the new lamp unit
ETighten the screws of the lamp unit
FAttach the lamp cover
zFasten the screws with a + screwdriver.
zInsert the top part (with 2 claws) of the lamp cover into the unit.
zFasten the screws with a + screwdriver.
zUse only genuine replacement 
parts for the lamp unit. Also, never 
attempt to re-use an old lamp unit.  
This may cause a malfunction.
zDo not touch the surface of a new 
lamp. This...

40
Replacing the Lamp (Continued)
5Troubleshooting
After installing a new lamp unit, reset the lamp hours.
AInsert the power plug to the power outlet
BReset lamp hours
Resetting Lamp Hours
zThe [LAMP] indicator and [STANDBY/ON] indicator blink alternately for 3 
seconds. After that, the unit switches to standby mode. 
LIGHT TESTEXIT MENU
ENTER
WARNING
LAMP
STANDBY/ON
zReset the lamp time only when you 
have replaced the lamp.
zNever reset it when the lamp is still 
in use. Otherwise, the approximate...