Philips 200wp7e User Manual

							
Regulatory Information
The equipment should draw power from a socket with an attached protectio\
n circuit (a three-prong socket). All 
equipment that works together (computer, monitor, printer, and so on) \
should have the same power supply 
source.
The phasing conductor of the rooms electrical installation should have \
a reserve short-circuit protection device 
in the form of a fuse with a nominal value no larger than 16 amperes (A\
).
To completely switch off the equipment, the power supply cable must be r\
emoved from the power supply 
socket, which should be located near the equipment and easily accessible\
.
A protection mark B confirms that the equipment is in compliance with \
the protection usage requirements of 
standards PN-93/T-42107 and PN-89/E-06251.
RETURN TO TOP OF THE PAGE
North Europe (Nordic Countries) Information
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/SAFETY/REGS/regulat.htm\
 (7 of 11)2006-08-04 11:01:19 AM 
						

							
Regulatory Information
Placering/Ventilation 
VARNING: 
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIG\
A, NÄR 
DU STÄLLER DIN UTRUSTNING PÅPLATS. 
 
Placering/Ventilation 
ADVARSEL: 
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT 
ER NEMT TILGÆNGELIGE. 
 
Paikka/Ilmankierto 
VAROITUS: 
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI 
IRROTTAA PISTORASIASTA. 
 
Plassering/Ventilasjon 
ADVARSEL: 
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR \
STØMTILFØRSEL ER LETTE Å NÅ. 
RETURN TO TOP OF THE PAGE
BSMI Notice (Taiwan Only)
 
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/SAFETY/REGS/regulat.htm\
 (8 of 11)2006-08-04 11:01:19 AM 
						

							
Regulatory Information
RETURN TO TOP OF THE PAGE
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht den in der Verordnung ü\
ber den Schutz vor Schäden durch 
Röntgenstrahlen festgelegten Vorschriften. 
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf \
die Unbedenklichkeit der Inbetriebnahme 
hinweist, da die Vorschriften über die Bauart von Störstrahlern na\
ch Anlage III ¤ 5 Abs. 4 der 
Röntgenverordnung erfüllt sind. 
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspric\
ht, ist darauf zu achten, daß 
1.  Reparaturen nur durch Fachpersonal durchgeführt werden. 
2.  nur original-Ersatzteile verwendet werden. 
3.  bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird. 
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Ro\
t nicht auf dunklem 
Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Augenbelas\
tung bei zu geringem 
Zeichenkontrast wären die Folge). 
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70d\
B (A) oder weniger. 
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß 
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND. RETURN TO TOP OF THE PAGE
End-of-Life Disposal 
Your new monitor contains materials that can be recycled and reused. Spe\
cialized companies can recycle your 
product to increase the amount of reusable materials and to minimize the\
 amount to be disposed of. 
Please find out about the local regulations on how to dispose of your ol\
d monitor from your local Philips dealer. 
(For customers in Canada and U.S.A.) 
This product may contain lead and/or mercury. Dispose of in accordance t\
o local-state and federal regulations. 
For additional information on recycling contact www.eia.org (Consumer Education Initiative) RETURN TO TOP OF THE PAGE
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/SAFETY/REGS/regulat.htm\
 (9 of 11)2006-08-04 11:01:19 AM 
						

							
Regulatory Information
Information for UK only  WARNING - THIS APPLIANCE MUST BE GROUNDING.
Important: 
This apparatus is supplied with an approved moulded 13A 
plug. To change a fuse in this type of plug proceed as 
follows: 
1. Remove fuse cover and fuse. 
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or 
BSI approved type. 
3. Refit the fuse cover. 
If the fitted plug is not suitable for your socket outlets, it 
should be cut off and an appropriate 3-pin plug fitted in its 
place. 
If the mains plug contains a fuse, this should have a value 
of 5A. If a plug without a fuse is used, the fuse at the 
distribution board should not be greater than 5A. 
Note: The severed plug must be destroyed to avoid a 
possible shock hazard should it be inserted into a 13A 
socket elsewhere. 
How to connect a plug 
The wires in the mains lead are coloured in accordance 
with the following code: 
BLUE - NEUTRAL (N) 
BROWN - LIVE (L) 
GREEN & YELLOW - GROUND (G) 
1. The GREEN AND YELLOW wire must be connected to 
the terminal in the plug which is marked with the letter G 
or by the Ground symbol 
 or coloured GREEN or GREEN 
AND YELLOW. 
2. The BLUE wire must be connected to the terminal which 
 
 
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/SAFETY/REGS/regulat.htm\
 (10 of 11)2006-08-04 11:01:19 AM 
						

							
Regulatory Information
is marked with the letter N or coloured BLACK. 
3. The BROWN wire must be connected to the terminal 
which marked with the letter L or coloured RED. 
Before replacing the plug cover, make certain that the cord 
grip is clamped over the sheath of the lead - not simply 
over the three wires. 
 
RETURN TO TOP OF THE PAGE 
        
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/SAFETY/REGS/regulat.htm\
 (11 of 11)2006-08-04 11:01:19 AM 
						

							
Other Related Information
   
        
 
 
•  Safety and Troubleshooting
 • FAQs
 • Troubleshooting
 • Regulatory Information
 •Information  
for Users in the U.S
 •Information  
for Users Outside the U.S
  
   
   
   
 
 
Other Related Information
Information for Users in the U. S.
For units set at 115 V : 
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT\
 three conductor cord 
a maximum of 15-feet long and a parallel blade, grounding type attachmen\
t plug rated 15 A, 125 V. 
For units set at 230 V: 
Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT\
 three conductor cord 
a maximum of 15-feet long and a tandem blade, grounding type attachment \
plug rated 15 A, 250 V. 
Information for Users outside the U.S.
For units set at 230 V: 
Use a Cord Set consisting of a minimum 18 AWG cord and grounding type at\
tachment plug rated 
15 A, 250 V. The Cord Set should have the appropriate safety approvals f\
or the country in which 
the equipment will be installed and / or be marked HAR. 
 
RETURN TO TOP OF THE PAGE 
       
    
   
 
        
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/SAFETY/saf_other.htm200\
6-08-04 11:01:19 AM 
						

							
About This Manual
   
        
 
 •  About This Guide
 • Notational Descriptions
  
   
   
   
  
About This Manual
About This Guide
This electronic users guide is intended for anyone who uses the Philips\
 LCD Monitor. It 
describes the LCD monitors features, setup, operation and other importa\
nt information. Its 
contents are identical to the information in our printed version.
It includes the following sections:
l     Safety and Troubleshooting Information provides tips and solutions for common problems 
as well as other related information you may need.
 
l     About This Electronic Users Manual gives an overview of information inc\
luded, along with 
notation icon descriptions and other documentation for your reference.
 
l     Product Information gives an overview of the monitors features as well as the technical 
specifications for this monitor.
 
l     Installing Your Monitor describes the initial setup process and gives an overview of how to 
use the monitor. 
l     On-Screen Display provides information on adjusting the settings on your monitor. 
l     Customer Care and Warranty contains a list of worldwide Philips Consumer Information 
Centers along with help desk phone numbers and information on the warran\
ty applicable 
to your product.
 
l     Glossary defines technical terms. 
l     Download and Print Option transfers this entire manual to your hard drive for easy 
reference.
 
 
RETURN TO TOP OF THE PAGE
 
Notational Descriptions
The following subsections describe notational conventions used in this d\
ocument. 
Notes, Cautions and Warnings     
 
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/ABOUT/ABOUT.HTM (1 of \
2)2006-08-04 11:01:26 AM 
						

							
About This Manual
Throughout this guide, blocks of text may be accompanied by an icon and \
printed in bold or italic 
type. These blocks contain notes, cautions or warnings. They are used as\
 follows:
NOTE: This icon indicates important information and tips that help you m\
ake 
better use of your computer system.
CAUTION: This icon indicates information that tells you how to avoid eit\
her 
potential damage to hardware or loss of data.
WARNING: This icon indicates the potential for bodily harm and tells you\
 how 
to avoid the problem.
 
Some warnings may appear in alternate formats and may not be accompanied\
 by an icon. In 
such cases, the specific presentation of the warning is mandated by the \
relevant regulatory 
authority.
 
RETURN TO TOP OF THE PAGE
©2006 Koninklijke Philips Electronics NV
All rights reserved. Reproduction, copying, use, modification, hiring, r\
enting, public performance, transmission and/or 
broadcasting in whole or in part is prohibited without written consent o\
f Philips Electronics NV
  
 
 
  
        
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/ABOUT/ABOUT.HTM (2 of \
2)2006-08-04 11:01:26 AM 
						

							
Product Information
   
        
 
• Product Features
• Technical Specifications
• Resolution & Preset Modes
• Philips Pixel Defect Policy
• Automatic Power Saving
• Physical Specification
• Pin Assignment
• Product Views
• Physical Function
• Rotating the Monitor
• SmartManage 
Product Information 
Product Features 
200WP7 
l     Outstanding front of screen performance 
m     WSXGA, wide format 1680x1050 resolution for sharper display 
m     Fast response time for better display of moving images
m     Viewing angle up to 178 degrees 
m     Dual input accepts both analog VGA and digital DVI signals 
l     Maximum comfort for maximum productivity 
m     SmartManage compatibility enables LAN-based asset management 
m     90 degree screen rotation and smart cable management 
m     Screen tilt and swivel adjustment for an ideal viewing angle 
m     Display more images and content without scrolling 
l     Great convenience  
m     Easy to adjust display settings with Philips SmartControl 
m     High-speed USB 2.0 hub for easy connections
m     Easy plug-and-play DVI for a true digital experience 
m     Embedded power supply eliminates external power adaptors
 
RETURN TO TOP OF THE PAGE 
Lead-free Product 
Philips eliminated toxic substances like lead from its displays. Lead-fr\
ee display helps protect your health 
and promotes environmentally sound recovery and disposal of waste from e\
lectrical and electronic 
equipment.Philips complies with the European Community stringent RoHS Di\
rective mandating 
restrictions on hazardous substances in electrical and electronic equipm\
ent. With Philips, you can be 
confident that your display device does not harm the environment.
 
  
Technical Specifications* 
LCD PANEL 
• Type TFT LCD
• Screen size 20.1 / 51cm
• Pixel Pitch 0.258 x 0.258mm
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/PRODUCT/product.htm (1\
 of 10)2006-08-04 11:01:33 AM 
						

							
Product Information
• LCD Panel type 1680 x 1050pixels 
R.G.B. vertical stripe  
Anti-glare polarizer, hard coated
 
• Effective viewing area
433.44 x 270.9mm
• Display Colors 8 bits interface (16.7M colors)
SCANNING
Vertical refresh rate56Hz-76Hz (Analog / Digital input)
Horizontal Frequency 30kHz-98kHz (Analog input)
VIDEO
• Video dot rate210 MHz 
• Input impedance - Video 75 ohm
- Sync 2.2K ohm
• Input signal levels 0.7 Vpp
• Sync input signal Separate sync
  
Composite sync 
Sync on green
 
• Sync polarities
Positive and negative
Optical characteristics 
• Peak contrast angle6 oclock
• White Chromaticity:  x: 0.283 y: 0.297 (at 9300°K) 
x: 0.313 y: 0.329 (at 6500°K)
* This data is subject to change without notice.
 
RETURN TO TOP OF THE PAGE
Resolution & Preset Modes
• Maximum 1680 x 1050 at 75Hz(analog input) 
1680 x 1050 at 60Hz(digital input) 
• 
Recommended 
1680 x 1050 at 60Hz(digital input) 
file:///D|/EDFU/LCD/200WP7/manual/ENGLISH/200WP7/PRODUCT/product.htm (2\
 of 10)2006-08-04 11:01:33 AM