Panasonic Wv Np502 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Wv Np502 Operating Instructions Manual. The Panasonic manuals for Camera are available online for free. You can easily download all the documents as PDF.
Page 51
![Page 51
51
Configure the settings relating to audio [Audio]
Click the [Audio] tab on the Image/Audiopage. (pages 20 and 21: How to display/operate the setup menu)
The settings relating to audio can be configured on this page.
Note: • Images and audio will not be synchronized. Therefore, images and audio m\
ay not always match.
• Audio may be interrupted depending on the network environment.
[Audio transmission/reception]
Select the communication mode used for audio data
transmission/reception between the camera...](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-50.png "Page 51
51
Configure the settings relating to audio [Audio]
Click the [Audio] tab on the Image/Audiopage. (pages 20 and 21: How to display/operate the setup menu)
The settings relating to audio can be configured on this page.
Note: • Images and audio will not be synchronized. Therefore, images and audio m\
ay not always match.
• Audio may be interrupted depending on the network environment.
[Audio transmission/reception]
Select the communication mode used for audio data
transmission/reception between the camera...")
51 Configure the settings relating to audio [Audio] Click the [Audio] tab on the Image/Audiopage. (pages 20 and 21: How to display/operate the setup menu) The settings relating to audio can be configured on this page. Note: • Images and audio will not be synchronized. Therefore, images and audio m\ ay not always match. • Audio may be interrupted depending on the network environment. [Audio transmission/reception] Select the communication mode used for audio data transmission/reception between the camera...
Page 52
![Page 52
52
[Mic input interval (Camera to PC)]
Select an interval for audio reception from the following.
20msec/40msec/80msec/160msec
Default:40msec
Note:
• When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected,
audio interruption may be diminished even though
the delay time will be longer.
Select the interval according to the network environ-
ment.
[Audio output volume (PC to Camera)]
Select a volume level on the camera to hear audio
transmitted from the PC....](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-51.png "Page 52
52
[Mic input interval (Camera to PC)]
Select an interval for audio reception from the following.
20msec/40msec/80msec/160msec
Default:40msec
Note:
• When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected,
audio interruption may be diminished even though
the delay time will be longer.
Select the interval according to the network environ-
ment.
[Audio output volume (PC to Camera)]
Select a volume level on the camera to hear audio
transmitted from the PC....")
52 [Mic input interval (Camera to PC)] Select an interval for audio reception from the following. 20msec/40msec/80msec/160msec Default:40msec Note: • When a shorter interval is selected, the delay time will be shorter. When a longer interval is selected, audio interruption may be diminished even though the delay time will be longer. Select the interval according to the network environ- ment. [Audio output volume (PC to Camera)] Select a volume level on the camera to hear audio transmitted from the PC....
Page 53
![Page 53
53
Configure the multi-screen settings [Multi-screen]
The cameras from which images are to be displayed on a multi-screen can \
be registered on the Multi-screen page.
(pages 20 and 21: How to display/operate the setup menu)
[IP address]
Enter the IP address or the host name of the camera to
be used for the multi-screen. 4 cameras can be regis-
tered as a group and up to 4 groups (16 cameras) can
be registered.
When the HTTP port number for the camera of which
images are to be displayed had been...](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-52.png "Page 53
53
Configure the multi-screen settings [Multi-screen]
The cameras from which images are to be displayed on a multi-screen can \
be registered on the Multi-screen page.
(pages 20 and 21: How to display/operate the setup menu)
[IP address]
Enter the IP address or the host name of the camera to
be used for the multi-screen. 4 cameras can be regis-
tered as a group and up to 4 groups (16 cameras) can
be registered.
When the HTTP port number for the camera of which
images are to be displayed had been...")
53 Configure the multi-screen settings [Multi-screen] The cameras from which images are to be displayed on a multi-screen can \ be registered on the Multi-screen page. (pages 20 and 21: How to display/operate the setup menu) [IP address] Enter the IP address or the host name of the camera to be used for the multi-screen. 4 cameras can be regis- tered as a group and up to 4 groups (16 cameras) can be registered. When the HTTP port number for the camera of which images are to be displayed had been...
Page 54
![Page 54
54
Configure the alarm settings [Alarm]
The settings relating to alarm occurrences such as settings for the alar\
m action at an alarm occurrence, the VMD
area settings, and the alarm occurrence notification can be configured on this page.
The Alarm page has 3 tabs; the [Alarm] tab, the [VMD area] tab and the\
[Notification] tab.
Configure the settings relating to the alarm action [Alarm]
Click the [Alarm] tab on the Alarm page. ( pages 20 and 21: How to display/operate the setup menu)
The settings...](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-53.png "Page 54
54
Configure the alarm settings [Alarm]
The settings relating to alarm occurrences such as settings for the alar\
m action at an alarm occurrence, the VMD
area settings, and the alarm occurrence notification can be configured on this page.
The Alarm page has 3 tabs; the [Alarm] tab, the [VMD area] tab and the\
[Notification] tab.
Configure the settings relating to the alarm action [Alarm]
Click the [Alarm] tab on the Alarm page. ( pages 20 and 21: How to display/operate the setup menu)
The settings...")
54 Configure the alarm settings [Alarm] The settings relating to alarm occurrences such as settings for the alar\ m action at an alarm occurrence, the VMD area settings, and the alarm occurrence notification can be configured on this page. The Alarm page has 3 tabs; the [Alarm] tab, the [VMD area] tab and the\ [Notification] tab. Configure the settings relating to the alarm action [Alarm] Click the [Alarm] tab on the Alarm page. ( pages 20 and 21: How to display/operate the setup menu) The settings...
Page 55
![Page 55
55
Configure the settings relating to the alarm image [Alarm]
Click the [Alarm] tab on the Alarm page. (pages 20 and 21: How to display/operate the setup menu)
The settings relating to the alarm image to be transmitted to an FTP ser\
ver can be configured in this section. The
alarm image will be transmitted to an FTP server. To transmit alarm imag\
es to an FTP server, it is necessary to con-
figure the settings in advance. ( page 70)
Refer to pages 54 and 57 for further information about the settings...](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-54.png "Page 55
55
Configure the settings relating to the alarm image [Alarm]
Click the [Alarm] tab on the Alarm page. (pages 20 and 21: How to display/operate the setup menu)
The settings relating to the alarm image to be transmitted to an FTP ser\
ver can be configured in this section. The
alarm image will be transmitted to an FTP server. To transmit alarm imag\
es to an FTP server, it is necessary to con-
figure the settings in advance. ( page 70)
Refer to pages 54 and 57 for further information about the settings...")
55 Configure the settings relating to the alarm image [Alarm] Click the [Alarm] tab on the Alarm page. (pages 20 and 21: How to display/operate the setup menu) The settings relating to the alarm image to be transmitted to an FTP ser\ ver can be configured in this section. The alarm image will be transmitted to an FTP server. To transmit alarm imag\ es to an FTP server, it is necessary to con- figure the settings in advance. ( page 70) Refer to pages 54 and 57 for further information about the settings...
Page 56
![Page 56
56
[Image compression rate upon alarm detection]
Select On or Off to determine whether or not to
change the image quality upon alarm detection.
On:Images will be transmitted with the image quality
selected for Image quality upon alarm detection.
Off: Does not change the image quality upon alarm
detection.
Default: Off
[Image quality upon alarm detection]
Image quality can be changed upon an alarm occur-
rence. Select the image quality from the following.
0 Super fine/1 Fine/2/3/4/5 Normal/6/7/8/9 Low...](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-55.png "Page 56
56
[Image compression rate upon alarm detection]
Select On or Off to determine whether or not to
change the image quality upon alarm detection.
On:Images will be transmitted with the image quality
selected for Image quality upon alarm detection.
Off: Does not change the image quality upon alarm
detection.
Default: Off
[Image quality upon alarm detection]
Image quality can be changed upon an alarm occur-
rence. Select the image quality from the following.
0 Super fine/1 Fine/2/3/4/5 Normal/6/7/8/9 Low...")
56 [Image compression rate upon alarm detection] Select On or Off to determine whether or not to change the image quality upon alarm detection. On:Images will be transmitted with the image quality selected for Image quality upon alarm detection. Off: Does not change the image quality upon alarm detection. Default: Off [Image quality upon alarm detection] Image quality can be changed upon an alarm occur- rence. Select the image quality from the following. 0 Super fine/1 Fine/2/3/4/5 Normal/6/7/8/9 Low...
Page 57
![Page 57
57
Configure the settings relating to the alarm output terminal [Alarm]
Click the [Alarm] tab on the Alarm page. (pages 20 and 21: How to display/operate the setup menu)
The settings relating to the alarm output terminal can be configured in \
this section. The settings for the alarm output
terminal can be configured only when Alarm output is selected for Terminal 2 of Alarm. Refer to pages 54 and
55 for further information about the settings relating to the alarm acti\
on, and the alarm image.
Alarm...](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-56.png "Page 57
57
Configure the settings relating to the alarm output terminal [Alarm]
Click the [Alarm] tab on the Alarm page. (pages 20 and 21: How to display/operate the setup menu)
The settings relating to the alarm output terminal can be configured in \
this section. The settings for the alarm output
terminal can be configured only when Alarm output is selected for Terminal 2 of Alarm. Refer to pages 54 and
55 for further information about the settings relating to the alarm acti\
on, and the alarm image.
Alarm...")
57 Configure the settings relating to the alarm output terminal [Alarm] Click the [Alarm] tab on the Alarm page. (pages 20 and 21: How to display/operate the setup menu) The settings relating to the alarm output terminal can be configured in \ this section. The settings for the alarm output terminal can be configured only when Alarm output is selected for Terminal 2 of Alarm. Refer to pages 54 and 55 for further information about the settings relating to the alarm acti\ on, and the alarm image. Alarm...
Page 58
![Page 58
58
[AUX (Up to 10 characters)]
Enter the name for AUX on the Live page.
Default:AUX
[Open (Up to 5 characters)]
Enter the name for Open of AUX on the Live page.
Default: Open
[Close (Up to 5 characters)]
Enter the name for Close of AUX on the Live page.
Default: Close
Change the AUX name [Alarm]
Click the [Alarm] tab on the Alarm page. ( pages 20 and 21: How to display/operate the setup menu)
The names of AUX, Open and Close on the Live page can be changed\
.](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-57.png "Page 58
58
[AUX (Up to 10 characters)]
Enter the name for AUX on the Live page.
Default:AUX
[Open (Up to 5 characters)]
Enter the name for Open of AUX on the Live page.
Default: Open
[Close (Up to 5 characters)]
Enter the name for Close of AUX on the Live page.
Default: Close
Change the AUX name [Alarm]
Click the [Alarm] tab on the Alarm page. ( pages 20 and 21: How to display/operate the setup menu)
The names of AUX, Open and Close on the Live page can be changed\
.")
58 [AUX (Up to 10 characters)] Enter the name for AUX on the Live page. Default:AUX [Open (Up to 5 characters)] Enter the name for Open of AUX on the Live page. Default: Open [Close (Up to 5 characters)] Enter the name for Close of AUX on the Live page. Default: Close Change the AUX name [Alarm] Click the [Alarm] tab on the Alarm page. ( pages 20 and 21: How to display/operate the setup menu) The names of AUX, Open and Close on the Live page can be changed\ .
Page 59
![Page 59
59
[Area]
When selecting a VMD area in the screen, it will be
numbered as area 1. (Subsequent areas will be num-
bered in the order of selection.)
[Status]
Select On or Off to determine whether or not to acti-
vate each VMD area.
On: Activates the respective VMD area.
Off: Inactivates the respective VMD area.
Default: Off [Detection area]
Adjust the size of the VMD area using the slider. The
smaller the selected value is, the higher the sensitivity
of VMD area becomes. The current value (1-10) will be...](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-58.png "Page 59
59
[Area]
When selecting a VMD area in the screen, it will be
numbered as area 1. (Subsequent areas will be num-
bered in the order of selection.)
[Status]
Select On or Off to determine whether or not to acti-
vate each VMD area.
On: Activates the respective VMD area.
Off: Inactivates the respective VMD area.
Default: Off [Detection area]
Adjust the size of the VMD area using the slider. The
smaller the selected value is, the higher the sensitivity
of VMD area becomes. The current value (1-10) will be...")
59 [Area] When selecting a VMD area in the screen, it will be numbered as area 1. (Subsequent areas will be num- bered in the order of selection.) [Status] Select On or Off to determine whether or not to acti- vate each VMD area. On: Activates the respective VMD area. Off: Inactivates the respective VMD area. Default: Off [Detection area] Adjust the size of the VMD area using the slider. The smaller the selected value is, the higher the sensitivity of VMD area becomes. The current value (1-10) will be...
Page 60
![Page 60
60
VMD information addition
[Information addition ]
Select On or Off to determine whether or not to add
VMD information to image data.
The VMD information can be searched by Panasonic
network disk recorders (WJ-ND400 series). Refer to the
operating instructions of the connected devices for fur-
ther information about the functions and settings.
Default: Off
Set the VMD areas
Important:
• When the settings are being configured on the setup menu, sometimes the \
VMD function may not work correctly....](http://img.usermanuals.tech/thumb/58/68511/w300_wv-np502_en_om_d-59.png "Page 60
60
VMD information addition
[Information addition ]
Select On or Off to determine whether or not to add
VMD information to image data.
The VMD information can be searched by Panasonic
network disk recorders (WJ-ND400 series). Refer to the
operating instructions of the connected devices for fur-
ther information about the functions and settings.
Default: Off
Set the VMD areas
Important:
• When the settings are being configured on the setup menu, sometimes the \
VMD function may not work correctly....")
60 VMD information addition [Information addition ] Select On or Off to determine whether or not to add VMD information to image data. The VMD information can be searched by Panasonic network disk recorders (WJ-ND400 series). Refer to the operating instructions of the connected devices for fur- ther information about the functions and settings. Default: Off Set the VMD areas Important: • When the settings are being configured on the setup menu, sometimes the \ VMD function may not work correctly....