Panasonic Wv Nf284 Operating Instructions Manual

31
Delete the set VMD area
Step 1
Click the [Delete] button respective to the area to be
deleted. 
→The outline of the area will disappear. 
Step 2
Click the [SET] button. 
→The deletion will be completed. 
Important:
The deletion will not be completed unless the [SET]
button is clicked.  

32
Configure the settings relating to the mail notification [Notification]
Click the [Notification] tab on the Alarm setup page. (☞page 15)
■E-mail notification setup
The settings relating to the alarm mail can be configured on this page. To notify of an alarm occurrence by e-mail, it
is necessary to configure the settings of the mail server. (☞page 36)
[E-mail notification]
Select ON or OFF to determine whether or not to
notify of an alarm occurrence by e-mail at an alarm
occurrence. 
Default...

33
Configure the settings relating to Panasonic alarm protocol
Click the [Notification] tab on the Alarm setup page. (☞page 15)
■Panasonic alarm protocol setup
The settings relating to Panasonic alarm protocol can be configured on this page. 
[Panasonic alarm protocol]
Select ON or OFF to determine whether or not to
notify of an alarm occurrence by Panasonic alarm proto-
col when an alarm is detected. 
Default setting:OFF
Note:
When ON is selected, the alarm occurrence will be
notified to the registered...

34
[User authentication]
Select ON or OFF to determine whether or not to
authenticate the user. 
Default setting:OFF
[User name]
Enter a user name. 
Number of characters for the user name:1 - 32 char-
acters
Default setting:(blank)
[Password] [Retype password]
Enter the password. 
Number of characters for the password:4 - 32 char-
acters
Default setting:(blank)
Note:
When the user name already in use is entered and
the [REG] button is clicked, the respective user infor-
mation will be overwritten....

35
Configure the settings relating to the host authentication [Host]
Click the [Host] tab on the Authentication setup page. (☞page 15)
The settings to restrict PCs (IP address) to access the camera can be configured on this page. 
[Host authentication]
Select ON or OFF to determine whether or not to
authenticate the host. 
Default setting:OFF
Important:
Before configuring the host authentication, it is nec-
essary to register IP addresses of the PCs to be
allowed to access the camera and determine their...

36
Configure the settings of the servers [Server setup]
The settings relating to the mail server and the FTP server can be configured on this page. 
The Server setup page has 2 tabs of the [Mail] tab and the [FTP] tab. 
Configure the settings relating to the mail server [Mail]
Click the [Mail] tab on the Server setup page. (☞page 15)
The settings relating to the mail server used to send the alarm mail can be configured on this page. 
[SMTP server address]*
Enter the IP address or the host name of the...

37
Configure the settings relating to the FTP server [FTP]
Click the [FTP] tab on the Server setup page. (☞page 15)
The settings relating to the FTP server used to transmit the alarm images can be configured on this page. 
[FTP server address]
Enter the IP address or the host name of the FTP serv-
er. 
Number of characters for the FTP server address:
1 - 128 characters
Note:
When entering localhost for FTP server address,
alarm images will be sent to the SD memory card. In
this case, images will not be...

38
Configuring the network settings [Network setup]
The network settings and the settings relating to DDNS (Dynamic DNS) and SNMP (Simple Network management
Protocol) can be configured on this page. 
The Network setup page has 4 tabs of the [Network] tab, the [DDNS] tab, the [SNMP] tab and the [FTP] tab. 
Configure the network settings [Network]
Click the [Network] tab on the Network setup page. (☞page 15)
The following information is required to configure the network settings. 
Contact the network...

39
[Default gateway]
When not using the DHCP function, enter the default
gateway of the camera. 
Default setting:192.168.0.1 

•0.*.*.*
•*.*.*.0
•255.*.*.*
•*.*.*.255
•127.0.0.1
•Class D address (224.0.0.0 - 239.255.255.255)
•Class E address (240.0.0.0 - 255.255.255.255)
*These IP addresses for the default gateway are
unavailable even when using the DHCP function.
Refer to the network administrator for the settings of
the DHCP server. 
[HTTP port]
Assign the port numbers independently. 
The following...

40
Notes:
•The port forwarding function changes a global IP address to a private IP address, and Static IP masquerade
and Network Address Translation (NAT) have this function. This function is to be set in a router. 
•To access the camera via the Internet by connecting the camera to a broadband router, it is necessary to assign
a respective port number for each camera and address translation by using the port forwarding function. For fur-
ther information, refer to the operating instructions of the...