Panasonic Wv Nf284 Operating Instructions Manual

21
Configure the settings relating to images and audio [Camera
setup]
The settings relating images and audio such as brightness and image quality of JPEG/MPEG-4 can configured on
this page. 
The Camera setup page has 3 tabs of the [JPEG/MPEG-4] tab, the [Camera] tab and the [Audio] tab. 
Configure the settings relating to JPEG/MPEG-4 images [JPEG/MPEG-4]
Click the [JPEG/MPEG-4] tab on the Camera setup page. (☞page 15)
■JPEG setup
Configure the settings such as Refresh interval (JPEG), Image capture size...

22
■MPEG-4 setup
Configure the settings relating to MPEG-4 image such as Max bit rate (per 1 client), Image capture size, Image
quality, etc. in this section. Refer to page 21 for further information about the settings relating to JPEG images. 
[MPEG-4 transmission]
Select ON or OFF to determine whether or not to
transmit MPEG-4 images. 
ON:Transmits MPEG-4 images. 
OFF:Does not transmit MPEG-4 images. 
Default setting:ON
Note:
When ON is selected for MPEG-4 transmission,
displaying rather of MPEG-4...

23
[Unicast port1 (Image)]
Enter the unicast port number (used to transmit image
from the camera).
Available value:1024 - 50000 (Only even numbers are
available.)
Default setting:32004
[Unicast port2 (Audio)]
Enter the unicast port number (used to transmit audio
from the camera). 
Available value:1024 - 50000 (Only even numbers are
available.)
Default setting:33004
[Multicast address]
Enter the multicast IP address. 
Images and audio will be transmitted to the designated
IP address. 
Available...

24
Configure the camera settings such as image quality and brightness, etc.\
 [Camera]
Click the [Camera] tab on the Camera setup page. (☞page 15)
The following are descriptions of how to configure the settings relating\
 to images such as brightness, etc. 
[Brightness]
17 steps (–8 - 8) are available for brightness. The value
–8 is the darkest and 8 is the brightest.
Default setting: 0
[White balance]
Select the white balance adjustment method from the
following. 
AUTO: Adjusts the white balance...

25
Configure the settings relating to audio [Audio]
Click the [Audio] tab on the Camera setup page.(☞page 15)
The settings relating to audio can be configured on this page. 
[Mic mode*]
Select ON or OFF to determine whether to turn on or
off audio on a PC. 
ON:Transmits audio from the camera to the PC. Audio
can be heard with images on the PC. Images and
audio will not be synchronized. 
OFF:Audio will not be transmitted from the camera to
the PC. Therefore, no settings and controls relating
audio will be...

26
Configure the multi-screen settings [Multi-screen setup]
The cameras to be used for the multi-screen display can be registered on this page. 
Refer to page 15 for descriptions of how to display images on a multi-screen.
*The following cameras are available for the multi-screen display. 
WV-NF284, WV-NS202, WV-NP240 series, WV-NP1000 series, WV-NW470S series, WV-NP472, WV-NS320
series
[IP address]
Enter the IP address or the host name of the camera to
be used for the multi-screen. 4 cameras can be...

27
Configure the alarm settings [Alarm setup]
The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the alarm
occurrence notification, and the VMD area settings can be configured on this page. 
The Alarm setup page has 3 tabs of the [Alarm] tab, the [VMD area] tab and the [Notification] tab. 
Configure the settings relating to the alarm action [Alarm]
Click the [Alarm] tab on the Alarm setup page. (☞page 15)
■Alarm setup
The settings relating to the...

28
Configure the settings relating to the alarm image
Click the [Alarm] tab on the Alarm setup page. (☞page 15)
■Alarm image setup
The settings relating to the alarm image to be transmitted to the FTP se\
rver can be configured on this page. The
alarm image will be transmitted to the FTP server. To transmit alarm ima\
ges to the FTP server, it is necessary to
configure the settings in advance. ( ☞page 37)
Refer to pages 27 and 29 for further information about the settings relating to the alarm action \...

29
Configure the settings relating to the alarm out connector
Click the [Alarm] tab on the Alarm setup page. (☞page 15)
■Alarm output terminal setup
The settings relating to the alarm out connector can be configured on this page. Refer to pages 27 and 28 for further
information about the settings relating to the alarm action at an alarm occurrence and the alarm image. 
[Alarm output setup]
Select ON or OFF to determine whether or not to
output the alarm signals to the alarm out connector
when an alarm is...

30
Set the VMD areas [VMD area]
Click the [VMD area] tab on the Alarm setup page. (☞page 15)
The video motion detection areas can be set on this page. 
When a motion is detected in the set area, the alarm action will be performed. 
Set the VMD areas
Step 1
Set the video motion detection area by dragging the
mouse on the screen. When the [All areas] button is
clicked, the whole area will become the VMD area, and
1 (White) will be automatically applied to Area. 
→The designated area will become the VMD...