Panasonic Wv Nf284 Operating Instructions Manual

							31
Delete the set VMD area
Step 1
Click the [Delete] button respective to the area to be
deleted. 
→The outline of the area will disappear. 
Step 2
Click the [SET] button. 
→The deletion will be completed. 
Important:
The deletion will not be completed unless the [SET]
button is clicked.  
						

							32
Configure the settings relating to the mail notification [Notification]
Click the [Notification] tab on the Alarm setup page. (☞page 15)
■E-mail notification setup
The settings relating to the alarm mail can be configured on this page. To notify of an alarm occurrence by e-mail, it
is necessary to configure the settings of the mail server. (☞page 36)
[E-mail notification]
Select ON or OFF to determine whether or not to
notify of an alarm occurrence by e-mail at an alarm
occurrence. 
Default setting:OFF
[Attach image]
Select ON or OFF to determine whether or not to
attach an image to the mail to be sent. 
Default setting:OFF
Note:
The settings for Image capture size of the Alarm
image setup section on the [Alarm] tab (☞page 28)
will be applied to the size of the image to be
attached.
■E-mail notification setup
[Destination address]
Enter the destination mail address. Up to 4 destination
addresses can be registered. 
To notify by e-mail when an alarm occurred, check the
Alarm checkbox respective to the desired address. 
To provide notification by e-mail when any of the follow-
ing has occurred, check the Diag. checkbox respective
to the desired address.
When notification of the remaining space of the SD
memory card has been provided (☞page 19)
When the SD memory card has become full/When
mounting of the SD memory card failed
To delete the registered address, click the [DEL] button
respective to the desired address.
Number of characters for the destination mail
address:3 - 128 characters
[Mail subject]
Enter the mail subject. 
Number of characters for the mail subject:0 - 50
characters
[Mail body]
Enter the mail body. 
Number of characters for the mail body:0 - 200 char-
acters
Note:
Notification mail will be sent with the following mes-
sage. (The message to be sent differs depending on
the status of the SD memory card.)
•The SD memory card is full. (This message will
be sent when the SD memory card becomes
full.)
•The SD memory card cannot be recognized.
(This message will be sent when the SD memory
card has failed to mount.) 
						

							33
Configure the settings relating to Panasonic alarm protocol
Click the [Notification] tab on the Alarm setup page. (☞page 15)
■Panasonic alarm protocol setup
The settings relating to Panasonic alarm protocol can be configured on this page. 
[Panasonic alarm protocol]
Select ON or OFF to determine whether or not to
notify of an alarm occurrence by Panasonic alarm proto-
col when an alarm is detected. 
Default setting:OFF
Note:
When ON is selected, the alarm occurrence will be
notified to the registered destination IP addresses in
order (to IP address 1 first, to IP address 8 last). 
[Destination port]
Select a destination port of the Panasonic alarm proto-
col from the following. 
Available value:1 - 65535
Default setting:1818
[Retry times]
Select a retry time of Panasonic alarm protocol. 
Available value:1 - 30
Default setting:2
■Panasonic alarm protocol
[Destination IP address]
Enter the destination IP address of the Panasonic alarm
protocol from the following. Host name is unavailable for
the IP address. Up to 8 destination addresses can be
registered. 
To notify by Panasonic alarm protocol when an alarm
occurred, check the Alarm checkbox respective to the
desired address.
To provide notification using Panasonic alarm protocol
when any of the following has occurred, check the
Diag. checkbox respective to the desired address.
•When notification of the remaining space of the SD
memory card has been provided (☞page 19)
•When the SD memory card has become full
•When mounting of the SD memory card has failed
To delete the registered address, click the [DEL] button
respective to the desired address. 
Important:
Confirm that the destination IP addresses are regis-
tered correctly. When a registered IP address does
not exist, notification may be delayed.  
						

							34
[User authentication]
Select ON or OFF to determine whether or not to
authenticate the user. 
Default setting:OFF
[User name]
Enter a user name. 
Number of characters for the user name:1 - 32 char-
acters
Default setting:(blank)
[Password] [Retype password]
Enter the password. 
Number of characters for the password:4 - 32 char-
acters
Default setting:(blank)
Note:
When the user name already in use is entered and
the [REG] button is clicked, the respective user infor-
mation will be overwritten. 
[Access level]
Select the access level of the host from the following. 
1. Administrator:Allowed all available operations of
the camera. 
2. Camera control:Allowed to display images from the
camera and to control the camera. The camera set-
ting configuration is unavailable. 
3. Live only:Only displaying live images is available.
The camera setting configuration and camera con-
trol are unavailable. 
Default setting:3. Live only
Note:
By clicking [i] of User name check, the registered
user can be selected and the selected user’s infor-
mation can be checked. 
The registered user will be displayed with the access
level. (Example: admin [1]) 
To delete the registered user, click the [DEL] button
after selecting the user to be deleted. 
Important:
If all users whose access level is 1. Administrator
is deleted, it will be impossible to configure the set-
tings.
Configure the settings relating to the authentication
[Authentication setup]
The settings relating to the authentication such as users and PCs restrictions for accessing the camera can be con-
figured on this page. 
The Authentication setup page has 2 tabs of the [User] tab and the [Host] tab. 
Configure the settings relating to the user authentication [User]
Click the [User] tab on the Authentication setup page. (☞page 15)
The settings relating to the user authentication can be configured on this page. Up to 16 users can be registered.  
						

							35
Configure the settings relating to the host authentication [Host]
Click the [Host] tab on the Authentication setup page. (☞page 15)
The settings to restrict PCs (IP address) to access the camera can be configured on this page. 
[Host authentication]
Select ON or OFF to determine whether or not to
authenticate the host. 
Default setting:OFF
Important:
Before configuring the host authentication, it is nec-
essary to register IP addresses of the PCs to be
allowed to access the camera and determine their
access levels. If ON is selected for Host authenti-
cation before registering the hosts (IP addresses), it
will be impossible to access the camera. 
[IP address]
Enter the IP address of the PC to be allowed to access
the camera. 
Host name is unavailable for the IP address. 
Notes:
•When IP address/subnet mask is entered, it is pos-
sible to restrict PCs in each subnet. 
For example, when 192.168.0.1/24 is entered and
2. Camera control is selected for the access level,
the PCs whose IP address is between 192.168.0.0
- 192.168.0.255 can access the camera with the
access level 2. Camera control. 
•When the IP address already in use is entered and
the [REG] button is clicked, the respective host infor-
mation will be overwritten. 
[Access level]
Select the access level of the host from the following. 
1. Administrator/2. Camera control/3. Live only
Refer to page 34 for further information about the
access level. 
Default setting:3. Live only
Note:
By clicking [i] of Host check, the registered host
can be selected and the selected host’s IP address
can be checked. 
The registered IP address will be displayed with the
access level. (Example: 192.168.0.21 [1]) 
To delete the registered host, click the [DEL] button
after selecting the IP address to be deleted.  
						

							36
Configure the settings of the servers [Server setup]
The settings relating to the mail server and the FTP server can be configured on this page. 
The Server setup page has 2 tabs of the [Mail] tab and the [FTP] tab. 
Configure the settings relating to the mail server [Mail]
Click the [Mail] tab on the Server setup page. (☞page 15)
The settings relating to the mail server used to send the alarm mail can be configured on this page. 
[SMTP server address]*
Enter the IP address or the host name of the SMTP
server used to send e-mails. 
Number of characters for the SMTP server address:
1 - 128 characters
[POP server address]*
When POP before SMTP is selected for Authentica-
tion, enter the IP address or the host name of the POP
server. 
Number of characters for the POP server address:
1 - 128 characters
Important:
When entering the host name for NTP server
address, it is necessary to configure the DNS set-
tings on the [Network] tab of the Network setup
page. (☞page 39)
[Authentication]
Select the authentication method to send e-mails from
the following. 
None:It is not necessary to clear any authentication to
send e-mails. 
POP before SMTP:It is necessary to clear the POP
server authentication first to use the SMTP server to
send e-mails. 
SMTP:It is necessary to clear the SMTP server authen-
tication to send e-mails. 
Default setting:None
Note:
When you don’t know the authentication method to
send e-mails, refer to the network administrator. 
[User name]
Enter the user name to access the server. 
Number of characters for the user name:1 - 32 char-
acters
[Password]
Enter the password to access the server. 
Number of characters for the password:0 - 32 char-
acters
[Sender mail address]
Enter the mail address of a sender. 
Entered mail address will be displayed in the From
(sender) line of the sent mails. 
Number of characters for the senders mail address:
3 - 128 characters 
						

							37
Configure the settings relating to the FTP server [FTP]
Click the [FTP] tab on the Server setup page. (☞page 15)
The settings relating to the FTP server used to transmit the alarm images can be configured on this page. 
[FTP server address]
Enter the IP address or the host name of the FTP serv-
er. 
Number of characters for the FTP server address:
1 - 128 characters
Note:
When entering localhost for FTP server address,
alarm images will be sent to the SD memory card. In
this case, images will not be sent to the FTP server
periodically.
Important:
When entering the host name for FTP server
address, it is necessary to configure the DNS set-
tings on the [Network] tab of the Network setup
page. (☞page 39)
[User name]
Enter the user name (login name) to access the FTP
server. 
Number of characters for the user name:1 - 32 char-
acters
[Password]
Enter the password to access the FTP server. 
Number of characters for the password:0 - 32 char-
acters[Control port]
Enter a control port number to be used for the FTP serv-
er.
Available port number:1 - 65535
Default setting:21
[FTP mode]
Select Passive or Active for the FTP mode.
Normally, select Passive. When failed to establish the
connection, select Active.
Default setting:Passive 
						

							38
Configuring the network settings [Network setup]
The network settings and the settings relating to DDNS (Dynamic DNS) and SNMP (Simple Network management
Protocol) can be configured on this page. 
The Network setup page has 4 tabs of the [Network] tab, the [DDNS] tab, the [SNMP] tab and the [FTP] tab. 
Configure the network settings [Network]
Click the [Network] tab on the Network setup page. (☞page 15)
The following information is required to configure the network settings. 
Contact the network administrator or your Internet service provider. 
•IP address
•Net mask
•Default gateway (when using the gateway server/router)
•HTTP port Number
•Primary DNS, Secondary DNS (when using DNS)
■Network setup
[DHCP]
Select ON or OFF to determine whether or not to use
the DHCP function. 
Configure the DHCP server not to assign the same IP
addresses used for the other network cameras and PCs
whose IP address is unique. Refer to the network
administrator for the settings of the server. 
Default setting:OFF[IP address]
When not using the DHCP function, enter the IP
address of the camera. Do not enter the IP address
already in use (for the PCs and the other network cam-
eras). 
Default setting:192.168.0.10

•0.*.*.*
•*.*.*.0
•255.*.*.*
•*.*.*.255
•127.0.0.1
•Class D address (224.0.0.0 - 239.255.255.255)
•Class E address (240.0.0.0 - 255.255.255.255)
*These IP addresses are unavailable even when
using the DHCP function. Refer to the network
administrator for the settings of the DHCP server. 
[Net mask]
When not using the DHCP function, enter the net mask
of the camera. 
Default setting:255.255.255.0  
						

							39
[Default gateway]
When not using the DHCP function, enter the default
gateway of the camera. 
Default setting:192.168.0.1 

•0.*.*.*
•*.*.*.0
•255.*.*.*
•*.*.*.255
•127.0.0.1
•Class D address (224.0.0.0 - 239.255.255.255)
•Class E address (240.0.0.0 - 255.255.255.255)
*These IP addresses for the default gateway are
unavailable even when using the DHCP function.
Refer to the network administrator for the settings of
the DHCP server. 
[HTTP port]
Assign the port numbers independently. 
The following port numbers are unavailable since they
are already in use. 
Available port number:1 - 65535
Default setting:80

20, 21, 23, 25, 42, 53, 67, 68, 69, 110, 123, 161,
162, 995, 10669, 10670
[DNS]
Select AUTO or MANUAL to determine whether or
not to use the DNS. When MANUAL is selected, it is
necessary to configure the settings for the DNS. 
When using the DHCP function, it is possible to obtain
the DNS address automatically by selecting AUTO.
Refer to the network administrator for further information
about the settings. 
Default setting:MANUAL
[Primary DNS], [Secondary DNS]
When MANUAL is selected for DNS, enter the IP
address of the DNS. Refer to the network administrator
about the IP address of the DNS. [Line speed]
Select the line speed for data transmission from the fol-
lowings. It is recommended to use the default setting
AUTO. 
AUTO:Line speed will be applied automatically. 
100MF:100 Mbps full-duplex
100MH:100 Mbps half-duplex
10MF:10 Mbps full-duplex
10MH:10 Mbps half-duplex
Default setting:AUTO
[FTP access]
Select Allow or Forbid to determine whether to allow
or forbid the FTP access. 
Default setting:Forbid
[Total bit rate]
Select the total bit rate for data transmission from the
followings. 
64 kbps/128 kbps/256 kbps/512 kbps/1024 kbps/
2048 kbps/4096 kbps/Unlimited
Default setting:Unlimited
Notes:
•When selecting 64 kbps, select OFF for Mic
mode on the Audio tab. (☞page 25)
•When 64 kbps is selected, it is impossible to carry
out the live-transmission of JPEG images and the
FTP periodic transmission simultaneously.  
						

							40
Notes:
•The port forwarding function changes a global IP address to a private IP address, and Static IP masquerade
and Network Address Translation (NAT) have this function. This function is to be set in a router. 
•To access the camera via the Internet by connecting the camera to a broadband router, it is necessary to assign
a respective port number for each camera and address translation by using the port forwarding function. For fur-
ther information, refer to the operating instructions of the broadband router in use. 
Enter [Global IP address + : 
(colon) + port number] in the 
Address box of the browser 
via the Internet. WAN
Global address
vvv.xxx.yyy.zzzLAN
Private address
192.168.0.254
vvv.xxx.yyy.zzz:82
vvv.xxx.yyy.zzz:81Broadband router
Internet 
(WAN)
Cable modem
xDSL modemAddress translation using the port 
forwarding function
vvv.xxx.yyy.zzz:82 → 192.168.0.2:82
Address translation using the port 
forwarding function
vvv.xxx.yyy.zzz:81 → 192.168.0.1:81Private address
192.168.0.2
Port number: 82
Private address
192.168.0.1
Port number: 81