Panasonic Vdr D105 Operating Instructions Manual

							81LSQT1040
Indications
Others
∫Playback indications∫Confirmatory indications
1Playback
;Pause
56Cue/Review playback
78Last/first scene paused
9/:Skip playback
D/ESlow motion playback
;1/2;Frame-by-frame playback
0h00m00sMotion picture playback time
Play mode
All scenes on the disc displayed
Scenes recorded on the selected 
date displayed
Scenes in the selected playlist 
displayed
No.10Scene number
Volume adjustment
RResume playback
Contents that have been 
protected on another device.
0 or
––The built-in battery is low. (l33)
°The warning/alarm indication 
appears when LCD monitor is 
rotated towards the lens side. 
Return the direction of the LCD 
monitor to normal position and 
check the warning/alarm 
indication.
No disc is inserted.
Unusable disc
D105(P)eng.book  81 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							82LSQT1040
Indications
Others
Messages
CANNOT RECORD.Data writing to the disc has failed.
NO DATA.There are no images recorded on the disc.
THIS DISC IS 
INCOMPATIBLE.You inserted an incompatible disc (copy-protected discs, etc.).
PLEASE CHECK THE 
DISC.You inserted a disc that cannot be read on this unit (a disc 
recorded in PAL video format etc.).
RECOMMENDED TO USE 
PANASONIC DISCYou inserted a disc that does not meet the DVD standard for 
quality and performance so you may not be able to record 
normally. Refer to the following support site for information 
about discs that have been confirmed as compatible by 
Panasonic.
http://panasonic.co.jp/pavc/global/cs/e_cam
(This website is in English only.)
CANNOT RECORD.
(THIS DISC IS FINALIZED)A finalized DVD-RW (Video format) or DVD-R has been 
inserted. After finalizing, the discs become play-only and cannot 
record. If you un-finalize a DVD-RW (Video format), it can be 
used for recording. (l71)
CANNOT RECORD. DISC 
IS FULL.
The disc is full or the number of scenes has reached the 
maximum limit so no further data can be recorded. Delete 
unnecessary scenes (l56) or insert a new disc.
CANNOT RECORD. THE 
NUMBER OF SCENES HAS 
EXCEEDED THE MAXIMUM 
LIMIT.
CANNOT OPERATE.
TEMPERATURE IS HIGH. 
PLEASE TURN OFF AND 
WAIT A WHILE.The temperature of the unit is high so it cannot be operated. 
Turn off the power, wait until the unit cools and then turn on the 
power again.
CANNOT UN-FINALIZE 
THIS DISC.DVD-R cannot be un-finalized.
DVD-RW (VR format) cannot be un-finalized. DVD-RW (VR 
format) after finalization can be recorded and edited in the same 
way as DVD-RW (VR format) before finalization.
PUSH THE RESET 
SWITCH.An irregularity in the unit has been detected. Press the RESET 
button to restart the unit. (l88)
CHANGE TO MANUAL 
MODE.
You are attempting to use a function that cannot be used 
simultaneously.
CANCEL MAGICPIX MODE.
TURN OFF THE VIDEO 
LIGHT.
D105(P)eng.book  82 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							83LSQT1040
Indications
Others
It is possible that the system cannot complete writing of a file normally when, for example, power is 
turned off for some reason during recording or editing.
If faulty management information is found when a disc is accessed, the following message may 
appear. Be sure to follow the messages. (Repairing may take time depending on the error.)
≥When you repair the disc, use a battery with 
sufficient battery power or the AC adaptor.
≥Depending on the condition of the data, it may not 
be possible to completely repair the data.
≥If the disc is removed without it being repaired, you 
will no longer be able to playback the scenes 
recorded before the power went off.≥Do not repair a disc that has been recorded on 
another device. This may cause the loss of data or 
the disc.
About recovery
DISC ERROR HAS OCCURRED. REPAIR DISC NOW?
D105(P)eng.book  83 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							84LSQT1040
Functions that cannot be used simultaneously
Others
Functions that cannot be used simultaneously
Some functions in this unit are disabled or cannot be selected due to the unit’s 
specifications. The table below shows examples of functions restricted by various 
conditions.
FunctionsConditions which
disable the functions
Backlight 
compensation≥When the MagicPix 
function is used
≥When the video light is 
on (gain up mode)
≥When the iris/gain is set
MagicPix≥When the video light is 
on (gain up mode)
Image 
stabilizer≥When the MagicPix 
function is used
≥When the video light is 
on (gain up mode)
Video light on 
(gain up 
mode)≥When the MagicPix 
function is used.FunctionsConditions which
disable the functions
Scene mode≥When setting the 
AUTO/MANUAL/
FOCUS switch to AUTO
≥When the MagicPix 
function is used
≥When the video light is 
on
Change of 
white balance≥When digital zoom 
(30k or higher) is used
≥When the MagicPix 
function is used
≥When the video light is 
on (gain up mode)
Adjusting the 
shutter speed, 
iris/gain≥When the MagicPix 
function is used
≥When the video light is 
on (gain up mode)
≥When the scene mode 
is used
D105(P)eng.book  84 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							85LSQT1040
Frequently asked questions
Others
Frequently asked questions
What kind of discs can be 
used?DVD-RAM, DVD-RW and DVD-R can be used if they are 8 cm 
(3z) bare discs. (l18)
Can discs with a cartridge 
be used?They can be used if the cartridge is removed.
Can double sided discs be 
used?They can be used. 
However you cannot record or play continuously from one side 
of the disc to the other. You will need to eject the disc and turn 
it over.
Can I record continuously 
from one side of the disc to 
the other on a double sided 
disc?You cannot record continuously from one side of the disc to 
the other. The recording time indicated on the disc package is 
the total time for both sides. You will need to eject the disc and 
turn it over to record on both sides.
Can DVD-R only be recorded 
to once only?Recording can be started and stopped until the disc is full.
However the data recorded on the DVD-R cannot be erased.
Is playback possible on a 
DVD player?By finalizing a DVD-RW (Video format) or a DVD-R in this unit, 
it can be played back on a DVD player.
DVD-RAM or DVD-RW (VR format) can be played back on a 
DVD recorder, DVD player etc. that supports DVD-RAM or 
DVD-RW (VR format). Refer to the operating instructions of 
the DVD recorder or DVD player.
≥DVD-RW (VR format) may have to be finalized. In this case, 
finalize the disc on this unit.
D105(P)eng.book  85 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							86LSQT1040
Troubleshooting
Others
Troubleshooting
ProblemCheck points
This unit cannot be 
turned on.≥Is the battery fully charged?
#Charge the battery using the AC adaptor. (l22)
This unit is turned off 
automatically.≥If you do not use the unit for approximately 5 minutes, the 
power is automatically turned off to conserve the battery 
charge. To resume recording, turn the power back on.
The power will not turn off automatically when the power 
save function (l79) is set to [OFF].
This unit does not stay 
on long enough.≥Is the battery low?
#If the remaining battery power indication is flashing or the 
message “LOW BATTERY.” is displayed, the battery has run 
down. Charge the battery. (l22)
Battery runs down 
quickly.≥Is the battery fully charged?
#Charge it with the AC adaptor. (l22)
≥Are you using the battery in an extremely cold place?
#The battery is affected by ambient temperature. In cold 
places, the operating time of the battery becomes shorter.
≥Has the battery worn out?
#The battery has a limited life. If the operating time is still too 
short even after the battery is fully charged, the battery has 
worn out and can no longer be used. 
This unit cannot be 
operated though 
powered up.
This unit does not 
operate normally.≥Press the RESET button. (l88) If normal conditions are 
not restored yet, remove the battery or AC adaptor, wait 
about 1 minute and then reconnect the battery or AC 
adaptor. Then about 1 minute later, turn on the power 
again. (Conducting the above operation when the access 
lamp is on may destroy the data on the disc.) 
The screen has changed 
suddenly.≥Has the demonstration started?
#If you set [DEMO MODE] to [ON] without inserting a disc in 
disc recording mode, the unit is automatically set to the 
demonstration mode for introducing its functions. Normally 
this should be set to [OFF]. Press the MENU button, then 
select [SETUP] # [DEMO MODE] # [OFF] and press the 
joystick.
The DISC EJECT lever 
does not work.≥The disc cover will not open unless the unit is powered.
#Connect a charged battery or AC adaptor.
D105(P)eng.book  86 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							87LSQT1040
Troubleshooting
Others
ProblemCheck points
A function indication 
such as mode indication, 
remaining time 
indication, or elapsed 
time indication is not 
shown.≥If you set [SETUP]>[DISPLAY]>[OFF], indications other 
than warnings and date indications disappear.
Recording does not start 
although power is 
supplied to this unit and 
the disc is correctly 
inserted.≥Is the DVD-RAM or the DVD-RW (VR format) write-
protected?
#Release the protection. (l72) If the DVD-RAM or DVD-RW 
(VR format) was protected on another device, release the 
protection on the same device.
≥Has the DVD-RW (Video format) or DVD-R been finalized?
#After finalizing, the discs become play-only and cannot 
record. If you un-finalize a DVD-RW (Video format), it can be 
used for recording. (l71)
≥Is the memory of the disc full?
#If the disc has no more available memory, free up some 
memory by deleting unnecessary scenes (l56) or use a 
new disc.
≥Is the unit set to the disc recording mode?
#No recording is possible unless the mode dial is at  .
≥Is the disc cover open?
#If the cover is open, this unit may not operate normally. Close 
the disc cover.
Recording starts but 
stops immediately.
The playback picture 
breaks up for a moment.≥Is the disc scratched or dirty?
#Clean the disc. (l21)
≥The unit is hot. Follow the messages on the display.
To use the unit again, turn the unit off and leave it for a 
while.
Auto focus function does 
not work.≥Is manual focus mode selected?
#Set the AUTO/MANUAL/FOCUS switch to AUTO.
≥Are you trying to record a scene which is hard to bring into 
focus in auto focus mode?
#There are some recording subjects and surroundings for 
which the auto focus does not operate correctly. (l94) If so, 
use the manual focus mode to adjust the focus. (l49)
≥Is the MagicPix function set? 
#When the MagicPix function is working, focusing shifts into 
the manual mode.
D105(P)eng.book  87 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							88LSQT1040
Troubleshooting
Others
ProblemCheck points
Sound is not played back 
from the built-in speaker 
of this unit.≥Is the volume too low?
#During playback, move the volume lever to display the 
volume indication and adjust it. (l54)
Although this unit is 
correctly connected to a 
TV, playback images 
cannot be seen.≥Have you selected video input on the TV? 
#Please read the operating instructions of your TV and select 
the channel that matches the input used for the connection.
Scenes cannot be deleted 
or edited.≥Is the DVD-RAM or the DVD-RW (VR format) write-
protected?
#Release the protection. (l72)
If the disc or the contents on the disc have been protected on 
another device, release the protection on the same device.
≥It may not be possible to delete scenes that have been 
divided.
#Combine the divided scenes, and then delete them. (l59)
≥Scenes displayed as thumbnails in shades of blue and 
white may not be deleted. If the scenes are unnecessary, 
format the disc to erase the data. (l69) Please be aware 
that if a disc is formatted then all the data recorded on the 
disc will be erased.
Even if a disc is 
formatted, it cannot be 
used.≥Either this unit or the disc may be damaged. Please 
consult a dealer.
The indication 
disappears.
The screen is frozen.
No operation can be 
performed.≥Turn off the power to this unit. If the power cannot be 
turned off, press the RESET button, or remove the battery 
or AC adaptor and then reattach it. After that, turn on the 
power again. If normal operation is still not restored, 
detach the power connected, and consult the dealer who 
you purchased this unit from.
“PUSH THE RESET 
SWITCH.” is displayed.≥The unit has automatically detected an 
error. Press the RESET button with the 
projecting part of the lens cap. This will 
restart the unit.
≥If you do not press the RESET button, 
the power to this unit is turned off automatically about 1 
minute later.
≥Even after you press the RESET button, the indication may 
still appear repeatedly. If so, this unit needs repair. Detach 
the power connected, and consult the dealer who you 
purchased this unit from. Do not attempt to repair the 
appliance by yourself.
D105(P)eng.book  88 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							89LSQT1040
Cautions for use
Others
Cautions for use
≥The unit and disc become warm after long 
operation, but this is not a malfunction.
Keep the unit away from magnetized 
products/mobile phones, microwave ovens, 
TVs and video game products.
≥If you use the unit on or near a TV, the 
images or sound may be disturbed due to 
electromagnetic wave radiation.
≥Do not use near cell phone because doing so 
may cause noise to adversely affect the 
picture and sound.
≥Recordings may be damaged, or images may 
be distorted, by the strong magnetic fields 
created by speakers or large motors.
≥Electromagnetic wave radiation generated by 
digital circuits including microprocessors may 
adversely affect the unit, causing the 
disturbance of images and sounds.
≥If the unit is affected by such products and 
does not function properly, turn off the unit 
and detach the battery or AC adaptor. Then 
connect the battery or AC adaptor again.
Do not use the unit near radio transmitters 
or high-voltage cables.
≥If you record pictures near radio transmitters 
or high-voltage cables, recorded images or 
sounds may be adversely affected.
Make sure to use the supplied cords and 
cables. If you use optional accessories, use 
the cords and the cables supplied with 
them.
Do not extend the cords and the cables.
Do not spray insecticides or volatile 
chemicals onto the unit.
≥If the unit is sprayed with such chemicals, its 
body may be marred and the surface finish 
may peel off.
≥Do not leave rubber or plastic products in 
contact with the unit for a long time.
When you use the unit in a sandy or dusty 
place such as a beach, do not let sand or 
fine dust get into the body and terminals of 
the unit.
Also, keep the unit away from sea water.≥Sand or dust may damage the unit. (Care 
should be taken when inserting and removing 
a disc.)
≥If sea water splashes onto the unit, wipe off 
the water with a well wrung cloth. Then wipe 
the unit again with a dry cloth.
When carrying the unit, do not drop or 
bump it.
≥A strong impact can break the unit’s casing, 
causing it to malfunction.
Do not use benzine, paint thinner or alcohol 
for cleaning the unit.
≥Before cleaning, detach the battery or pull out 
the AC cable from the AC outlet.
≥The camera body may be discolored and the 
surface finish may peel off.
≥Wipe the unit with a soft dry cloth to remove 
dust and fingerprints. To remove stubborn 
stains, thoroughly wring a cloth that has been 
soaked in a neutral detergent diluted with 
water and wipe the unit with it. Afterwards, 
wipe it with a dry cloth.
≥When you use a chemical dust cloth, follow 
the instructions that came with the cloth.
Do not touch the laser pickup lens.
≥If you touch the laser pickup lens directly it 
may cause malfunctions.
Do not use a commercial available 8 cm (3z) 
CD lens cleaner.
≥Using 8 cm (3z) CD lens cleaner could cause 
this unit to malfunction.
Do not use the unit for surveillance 
purposes or other business uses.
≥If you use the unit for a long time, heat will 
build up inside it and this may cause a 
malfunction.
≥This unit is not intended for business use.
When you are not going to use the unit for 
an extended time
≥When storing the unit in a cupboard or 
cabinet, it is recommended that you place a 
desiccant (silica gel) in with it.
About this unit
D105(P)eng.book  89 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							90LSQT1040
Cautions for use
Others
The battery used in this unit is a rechargeable 
lithium-ion battery. It is susceptible to humidity 
and temperature and the effect increases the 
more the temperature rises or falls. In cold 
areas, the full charge indication may not appear 
or the low battery indication may appear about 
5 minutes after starting use. At high 
temperatures, the protection function may be 
triggered, making it impossible to use the unit.
Be sure to detach the battery after use.
≥If the battery is left attached, a minute 
amount of current continues to flow even if 
the unit’s power is off. Keeping the unit in this 
state may result in over discharge of the 
battery. This may result in you not being able 
to use the battery even after it is charged.
Prepare spare batteries when going out for 
recording.
≥In cold places such as a ski resort, the period 
during which you can record pictures is 
shortened. 
≥When you travel, do not forget to bring an AC 
adaptor (supplied) so that you can recharge 
the batteries at your destination.
If you drop the battery accidentally, check to 
see if the terminals are damaged.
≥Attaching a battery with damaged terminals 
can damage the unit.
Tips for storing the battery
≥The battery should be stored in the vinyl bag 
so metal does not come into contact with the 
terminals.
≥The battery should be stored in a cool place 
free from humidity, with as constant 
temperature as possible. (Recommended 
temperature: 15 °C to 25 °C (59 °F to 77 °F), 
Recommended humidity: 40% to 60%) 
≥Extremely high temperatures or low 
temperatures will shorten the life of the 
battery.
≥If the battery is kept in high-temperature, 
high-humidity, or oily-smoky places, the 
terminals may rust and cause malfunctions.
≥To store the battery for a long period of time, 
we recommend you charge it once every year and store it again after you have 
completely used up the charged capacity. 
≥Dust and other matter attached to the battery 
terminals should be removed.
Do not throw old battery into fire.
≥Heating a battery or throwing it into a fire may 
result in an explosion.
≥If the operating time is very short even after 
the battery has been recharged, the battery 
has worn out. Please purchase a new battery. 
About the battery
D105(P)eng.book  90 ページ  ２００６年１月１６日　月曜日　午後４時１分