Panasonic Vdr D105 Operating Instructions Manual

							21LSQT1040
Before using
Discs
∫How to hold a disc
Do not touch the recorded surface.
∫If there is dirt or condensation on the disc
Wipe with a damp cloth and then wipe dry.
∫Handling precautions
≥Be careful about scratches and dirt.
≥Do not attach labels or stickers to discs. (This may cause disc warping and un-balanced rotation, 
rendering it unusable.)
≥Write on the label side of the disc only with a soft, oil-based felt pen. Do not use ballpoint pens or 
other hard writing implements.
≥Do not use record cleaning sprays, benzine, thinner, static electricity prevention liquids or any 
other solvent.
≥Do not use scratch-proof protectors or covers.
≥Do not drop, stack, or impact discs. Do not place objects on them.
≥Do not use the following discs:
– Discs with exposed adhesive from removed stickers or labels.
– Discs that are badly warped or cracked.
– Irregularly shaped discs, such as heart shapes.
≥Do not place in the following areas:
– In direct sunlight.
– In very dusty or humid areas.
– Near a heater.
– Locations susceptible to significant difference in temperature (condensation can occur).
– Where static electricity or electromagnetic waves occur.
≥To protect discs, return them to their cases when you are not using them.
Disc handling
D105(P)eng.book  21 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							22LSQT1040
Setup
Power supply
Setup
Power supply
When this unit is purchased, the battery is not charged. Charge the battery before using this unit.
≥If the DC cable is connected to the AC adaptor, then the battery will not charge. Remove 
the DC cable from the AC adaptor.
1 Connect the AC cable to the AC adaptor and the 
AC outlet.
2 Put the battery on the battery mount by aligning 
the mark, and then securely plug it in.
≥The output plug of the AC cable is not completely connected to the 
AC adaptor jack. As shown in A, there is a gap.
∫Charging lamp
Lights up: Charging
Goes off: Charging completed
Flashing: The battery is over discharged (discharged excessively). In a while, the lamp will light up 
and normal charging will start.
When the battery temperature is excessively high or low, the CHARGE lamp flashes and 
the charging time will be longer than normal.
≥Battery charging time (l23)
≥We recommend using Panasonic batteries.≥If you use other batteries, we cannot guarantee the 
quality of this product.
Push the battery against the battery holder and slide 
it until it clicks.
While sliding the BATTERY RELEASE lever, slide the 
battery to remove it.
≥Hold the battery with your hand so it does not fall.
≥Be sure to turn off the power on this unit and check 
that the status indicator and the access lamp are 
both off before removing the battery.
Charging the battery
A
Fitting the battery
Removing the battery
D105(P)eng.book  22 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							23LSQT1040
Setup
Power supply
The times shown in the tables below are for when the temperature is 25oC (77oF) and the humidity 
is 60%. If the temperature is higher or lower than 25oC (77oF), the charging time will become 
longer.
∫Charging time
≥“2 h 25 min” indicates 2 hours 25 minutes.
≥The charging time shown in the table are approximations.
∫Recordable time
≥The times indicate the recordable time when the viewfinder is used. The times in parentheses 
indicate the recordable time when the LCD monitor is used.
(When using a DVD-RAM disc)
≥“1 h 50 min” indicates 1 hour 50 minutes.
≥The maximum continuously recordable time shown in the table are approximations.
≥Along with the reduction of the battery capacity, the 
display will change: 
####.
If the battery discharges, then   ( ) will 
flash.
≥The recordable time will become shorter when you 
use both the viewfinder and the LCD monitor 
simultaneously while rotating the LCD monitor 
frontward to record yourself, etc.≥The batteries heat up after use or charging. This 
unit will also heat up while being used. This is not a 
malfunction.
≥Be aware that the operating time of the battery will 
become shorter in low temperatures. We 
recommend charging a spare battery for use when 
recording.
Charging time and recordable time
Battery model numberVoltage/capacityCharging time
Supplied battery/
CGA-DU12 (optional)7.2 V/1150 mAh 2 h 25 min
CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min
Battery model 
numberVoltage/capacityRecording modeMaximum 
continuously 
recordable time
Supplied battery/
CGA-DU12 (optional)7.2 V/1150 mAhXP1h50min
(1h40min)
SP2h5min
(1h50min)
LP2h15min
(2 h)
CGA-DU21 (optional) 7.2 V/2040 mAhXP3h30min
(3h10min)
SP3h55min
(3h30min)
LP4h20min
(3h50min)
D105(P)eng.book  23 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							24LSQT1040
Setup
Power supply
1 Connect the AC cable to the AC adaptor and 
the AC outlet.
2 Connect the DC cable to the AC adaptor.
3 Connect the DC cable to this unit.
≥Do not use the AC cable for other equipment since the AC 
cable is exclusively designed for this unit. Do not use the AC 
cable from other equipment for this unit.
≥While the DC cable is connected to the AC adaptor, 
the battery will not charge.
≥When recording, remove the lens cap before turning the unit on.
If the unit is turned on with the lens cap fitted, the automatic white balance adjustment may not 
function properly.
While pressing the button A, set the 
OFF/ON switch to ON.
The status indicator B lights red.
≥The date and time display flashes. Set this. (l33)
While pressing the button A, set the OFF/ON switch to 
OFF.
The status indicator B goes off.
Connecting to the AC outlet
Turning the unit on/off
How to turn on the power
A
B
How to turn off the power
A
B
When the power is turned on for the first time after changing the disc or battery, the unit carries 
out a recognition procedure to check that there are no problems with the disc.
This takes approximately 25 seconds with DVD-RAM.
If you want to start using the unit as soon as you turn on the power, do the following.
1) Turn on the power.
2) After “READING DISC...” disappears from the screen, turn off the power.
You can start recording approximately 8 seconds after you turn on the power again.
≥Depending on the condition of the disc, it may take longer than this.
≥If the date and time are not set, this function does not work.
D105(P)eng.book  24 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							25LSQT1040
Setup
Inserting/removing a disc
Inserting/removing a disc
When inserting or removing the disc, fit the charged battery pack or connect the AC adaptor to the 
unit. The cover of the disc compartment will not open unless the unit is powered.
1 Slide the DISC EJECT lever once and 
release it.
A few moments after the ACCESS/PC lamp blinks, 
the cover of the disc compartment will open slightly.
2 Open the cover of the disc compartment by hand and insert/remove 
the disc.
∫Inserting disc
Fit the disc onto the spindle in the center.
ARecording/playback side
BPickup lens
∫Removing disc
While pressing down on the spindle, grasp the edge of the disc and gently lift it out.
3 Push the section marked “PUSH CLOSE” on the cover of the disc 
compartment to close the cover.
A B
Click!
D105(P)eng.book  25 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							26LSQT1040
Setup
Inserting/removing a disc
∫Identifying recording/playback sides of disc
Single sided disc:
The recording/playback side is opposite to the labelled side.
Double sided disc:
The “SIDE A” recording/playback side is opposite to the “SIDE A” marked 
side. The “SIDE B” recording/playback side is the “SIDE A” marked side.
≥Do not use excessive force when opening the cover.
≥Do not touch the pickup lens or the recording/
playback side of the disc. 
This may impair recording and playback. 
≥Insert the disc securely to prevent damage.
≥When you open the cover, the ACCESS/PC lamp 
flashes red. Do not leave the cover open.
≥If the cover is open, the power will not turn off even 
if the OFF/ON switch is set to OFF.
≥If the disc is not correctly inserted, the cover will not 
close. Never try to forcibly close the cover. This 
could cause damage. Reinsert the disc properly.
≥If a single sided disc is inserted into the unit with the 
printed label facing the inside, an error message will 
appear. Remove the disc and reinsert it with its 
recording/playback side facing the inside.
≥Do not allow the recording/playback side to become 
dirty or scratched.≥Do not remove the battery pack or disconnect the 
AC adaptor while removing the disc or until power is 
completely turned off. If you do, the cover will not 
open. If this happens, reattach the battery pack or 
reconnect the AC adaptor, slide the DISC EJECT 
lever once, and then release it. A repair disc 
message may be displayed when the power is 
turned back on. (l83, About recovery)
≥Do not insert anything other than the 8 cm (3z) 
DVD-RAM, DVD-RW or DVD-R disc into the disc 
compartment. Doing so could cause malfunctions.
≥Do not touch the pickup lens or other parts inside 
the disc compartment. Be sure not to touch the area 
around the pickup lens for it becomes extremely 
hot.
DVD-RAM/SIDEA
“SIDE A” mark
The opposite side is 
the “SIDE A” recording/ 
playback side.
After inserting a disc/After recording finishes
While the ACCESS/PC lamp is lit, the disc is rotating and disc information is being recorded. If 
the power supply is interrupted at this time, the disc may become unusable. Do not disconnect 
the AC adaptor or remove the battery. Also, do not strongly shake or cause impact to the unit.
D105(P)eng.book  26 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							27LSQT1040
Setup
Selecting a mode
Selecting a mode
The mode dial is used to switch between recording and playback modes.
Rotate the mode dial slowly but surely.
≥Do not forcefully turn the dial.
Rotate the mode dial, and set the desired 
mode pictograph to the position shown in 
the illustration.
Disc recording mode (l36)Use this to record motion pictures on a disc.
Disc playback mode (l53)Use this to play back motion pictures on a disc.
D105(P)eng.book  27 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							28LSQT1040
Setup
How to use the joystick
How to use the joystick
This unit has a joystick for selecting functions, performing operations, etc. so it is easy to operate 
this unit with one hand.
Operations on the menu screen and selection of files on the thumbnail view screen, etc.
Move the joystick up, down, left, or right to select an item or file, and then 
press the joystick to set it.
≥Menu screen operations (l31)
Press the center of the joystick, and icons will be displayed on the screen. Each press switches the 
display as follows depending on the mode.
(In the disc playback mode, the icons will be automatically displayed on the screen.)
Basic operations
1Select by moving up.
2Select by moving down.
3Select by moving left.
4Select by moving right.
5Press the joystick to select the item.
Joystick and screen display
Disc recording mode
(AUTO/MANUAL/FOCUS switch is set to AUTO)
A: The operation icon is off.
IconDirectionFunctionPage
—4Soft skin mode 40
2Fade 41
ª1Backlight compensation 43
1
34
2
5
A
D105(P)eng.book  28 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							29LSQT1040
Setup
How to use the joystick
Disc recording mode
(AUTO/MANUAL/FOCUS switch is set 
to MANUAL)
A: The operation icon is off.
IconDirectionFunctionPage
(1/2)4Soft skin mode 40
2Fade 41
ª1Backlight compensation 43
(2/2)3Manual white balance set
(Only when manual white balance adjustment 
mode is selected)51
4White balance 50
Shutter speed 52
Iris or gain value 52
s
r21White balance mode selection, manual 
adjustments49, 50, 52
Disc playback mode
A: The operation icon is off.
IconDirectionFunctionPage
—1/;3Playback/pause 53
∫4Stop playback and show thumbnails 53
:
2Rewind, skip (during playback) 53
2;Reverse slow/frame playback (during pause) 54
9
1Fast forward, skip (during playback) 53
;1Forward slow/frame playback (during pause) 54
A
A
D105(P)eng.book  29 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							30LSQT1040
Setup
Switching the language
Switching the language
You can switch the language on the screen display or the menu screen.
1 Press the MENU button, then select [ LANGUAGE] 
and press the joystick.
2 Select [English] and press the joystick.
D105(P)eng.book  30 ページ  ２００６年１月１６日　月曜日　午後４時１分