Panasonic Vdr D105 Operating Instructions Manual

							51LSQT1040
Recording
Manual recording functions
Select [ ] mode, fill the screen with a white subject 
and then move the joystick up to select [ ].
When the [ ] display changes from flashing to on, setting is complete.
≥When the [ ] display continues flashing green, the white balance 
cannot be set because the place is dark etc. In this case, use the 
automatic white balance.
∫About the white balance sensor A
The white balance sensor detects the type of light source during 
recording.
Do not cover the white balance sensor during recording, or it may 
not function properly.
≥When the [ ] display flashes white, the manual 
white balance previously adjusted is stored.
Whenever recording conditions change, re-set the 
white balance for correct adjustment.
≥When the unit is turned on with the lens cap fitted, 
the automatic white balance adjustment may not 
function properly. Please turn the unit on after 
removing the lens cap.≥When setting both the white balance and the iris/
gain, set the white balance first.
To set the white balance manually
MNL
A
D105(P)eng.book  51 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							52LSQT1040
Recording
Manual recording functions
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
¬Rotate the mode dial to select  .
1 Set the AUTO/MANUAL/FOCUS switch to MANUAL.
The icon shown in the illustration is displayed automatically.
2 Move the joystick down several times and select 
the shutter speed indication (such as 1/100) or iris/
gain indication (such as F2.4, 0dB).
3 Move the joystick left or right to make the 
adjustment.
AShutter speed: 1/60 to 1/8000
≥The shutter speed closer to 1/8000 is faster.
BIris/Gain value: 
CLOSE # (F16 to F2.0) # OPEN # 0dB # 18dB
≥Value closer to [CLOSE] darken the image. 
≥Value closer to [18dB] brighten the image.
≥Values with [dB] are gain values.
To restore to automatic adjustment
Set the AUTO/MANUAL/FOCUS switch to AUTO.
≥When setting both the shutter speed and the iris/
gain value, set the shutter speed and then set the 
iris/gain value.
∫Manual shutter speed adjustment≥Avoid recording under fluorescent light, mercury 
light or sodium light because the color and 
brightness of the playback image may change.
≥If you increase the shutter speed manually, the 
sensitivity lowers and accordingly the gain value 
increases automatically, which may increase the 
noises on the screen.
≥You may see vertical lines of light in the playback 
image of a brightly shining subject or highly 
reflective subject, but this is not a malfunction.
≥During normal playback, image movement may not 
look smooth.≥When recording in an extremely bright place, the 
screen may change color or flicker. If so adjust the 
shutter speed manually to [1/60] or [1/100].∫Manual iris/gain adjustment≥If the gain value is increased, the noise on the 
screen increases.
≥Depending on the zoom magnification, there are iris 
values that are not displayed.
Manual shutter speed/aperture adjustment
Shutter Speed:Adjust it when recording fast-moving subjects. 
Aperture:Adjust it when the screen is too bright or too dark.
MNL
MNL
1/6060OPENOPENOdBOdB
1/100OPEN
MNL
1/6060OPENOPENOdBOdB
1/100OPEN
A
B
D105(P)eng.book  52 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							53LSQT1040
Playback
Motion picture playback
Playback
Motion picture playback
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
1 Rotate the mode dial to select  .
The motion pictures recorded on the disc are displayed 
as thumbnails.
2 Select the scene to be played back.
AScene number
BScroll bar display
The selected scene will be encircled by a red frame.
≥When 9 or more scenes have been recorded, the next (or previous) page 
is displayed by moving the joystick.
≥If you move and hold the joystick up or down, you can advance 8 scenes 
at a time. The screen will not change at this time, but the scene numbers 
and scroll bar display will change so release the joystick when you have 
arrived at the page with the scene you want to display.
3 Press the joystick.
The selected scene is played back on the full screen.
The operation icon is automatically displayed on the screen.
4 Move the joystick to operate.
≥During playback, the recording time is not displayed 
on the screen.
≥No sound will be heard except during normal 
playback.
≥If pause play is continued for 5 minutes, the screen 
returns to the thumbnails.≥When the amount of time recorded on the scene is 
short, playback may not be possible.
≥The thumbnails of motion pictures that cannot be 
played back are displayed in shades of blue and 
white.
A
B
12. 15. 2006
1/;: Playback/Pause
:(Move): Skip playback (backward)
:(Move and hold): Review playback
9(Move): Skip playback (forward)
9(Move and hold): Cue playback
∫: Stops the playback and shows the thumbnails.
D105(P)eng.book  53 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							54LSQT1040
Playback
Motion picture playback
1 Move the joystick up during playback to pause the 
playback.
2 Move and hold the joystick right.
(Slow-motion pictures will be played back in reverse 
when you move and hold the joystick left.)
≥Normal playback is restored when you move the joystick up.
The motion picture is advanced one frame at a time.
1 Move the joystick up during playback to pause the 
playback.
2 Move the joystick right. 
(The frames will be advanced one at a time in the 
reverse direction when you move the joystick left.)
≥Normal playback is restored when you move the joystick up.
Adjust the speaker volume during playback.
Move the volume lever to change the volume 
level.
≥The further the [ ] indicator moves to the right (towards the “i” end), the higher the volume level 
becomes.
≥When the adjustment is completed, the volume setting display will disappear.
Slow-motion playback
Frame-by-frame playback
To adjust the volume
To w a r d s  “r”:increases the volume
To w a r d s  “s”:decreases the volume
D105(P)eng.book  54 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							55LSQT1040
Playback
Motion picture playback
Recorded scenes are grouped by date on this unit.
Scenes recorded on the same day can be played back in succession.
1 Press the MENU button, then select 
[PLAYSETUP] # [PLAYMODE] # [BY DATE] 
and press the joystick.
≥When [PLAY MODE] is set to [VIEW ALL], all recorded motion 
pictures will be played back in succession. ([ ALL] is displayed.)
2 Select the date for playback, then press the joystick.
The scenes recorded on the same day are displayed as thumbnails.
3 Select the scene to be played back.
≥Even if scenes are recorded on the same day, they are grouped separately in the following cases.
– When the number of scenes exceeds 99 (RAM) (-RW‹VR›) (-RW‹V›) (-R)
– When the disc is removed (-RW‹V›) (-R)
– When the disc is repaired (-RW‹V›) (-R)
– When the mode dial is switched (-R)
– When the power is turned off (-R)
Press the MENU button, then select [ PLAY SETUP] 
# [ RESUME PLAY] # [ON] and press the joystick.
If playback of a motion picture is stopped, [R] appears on the thumbnail 
view of the stopped scene.
≥If playback is stopped at any point during a motion picture while 
[RESUME PLAY] is set to [OFF], the next time the motion picture is 
played back, it will be from the beginning.
≥The resume position memorized is cleared if the 
unit is turned off, but the menu setting is not 
cleared.
Playing back motion pictures by date
Resuming the previous playback
D105(P)eng.book  55 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							56LSQT1040
Editing
Editing scenes
Editing
Editing scenes
(RAM) (-RW‹VR›)
The deleted scenes cannot be restored.
≥Scenes on DVD-RW (Video format) and DVD-R cannot be deleted.
¬Rotate the mode dial to select  .
1 Press the   button during playback.
2 When the confirmation message appears, select [YES], then press the 
joystick.
¬Rotate the mode dial to select  .
1 Press the MENU button, then select [ DELETE] # 
[ SELECT] or [ ALL] and press the joystick.
≥When [ALL] is selected, the following scenes will be deleted. Proceed to 
step 4.
– When [PLAY MODE] is set to [VIEW ALL]: All the scenes on the disc
– When [PLAY MODE] is set to [BY DATE]: All the scenes selected by date
2(Only when [SELECT] is selected in step 1)
Select the scene to be deleted, then press the 
joystick.
The selected scene is encircled by a yellow frame.
≥When the joystick is pressed again, the selected scene will be canceled.
≥Up to 8 scenes displayed on a page can be set in succession.
3(Only when [SELECT] is selected in step 1)
Press the   button.
4 When the confirmation message appears, select [YES], then press the 
joystick.
(Only when [SELECT] is selected in step 1)
To continue deleting other scenes
Repeat steps 2-4.
Deleting scenes
This is for deleting scenes recorded on discs.
Deleting scenes one at a time
Deleting multiple scenes from the thumbnail display
D105(P)eng.book  56 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							57LSQT1040
Editing
Editing scenes
To complete editing
Press the MENU button.
≥To delete an unwanted part of a scene, divide the 
scene first, and then delete the unnecessary part. 
(l58)
≥In case of [ALL], the deletion may take time if there 
are many scenes on the disc.
≥Do not turn off this unit while deleting.≥When you delete scenes, use a battery with 
sufficient battery power or use the AC adaptor.
≥It may not be possible to delete scenes that have 
been divided. Combine the divided scenes, and 
then delete them.
D105(P)eng.book  57 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							58LSQT1040
Editing
Editing scenes
(RAM) (-RW‹VR›)
To delete unnecessary portion of scene, first divide the scene, and then delete the unnecessary 
portion.
¬Rotate the mode dial to select  .
1 Press the MENU button, then select 
[ EDIT SCENE] # [ DIVIDE] and press the 
joystick.
2 Select the scene to be divided, then press the 
joystick.
The selected scene is played back.
3 When you reach the area where you want to divide 
the scene, move the joystick down to set the 
dividing point.
4 When the confirmation message appears, select [YES], then press the 
joystick.
To continue dividing other scenes
Repeat steps 2-4.
To complete editing
Press the MENU button.
Dividing a scene
This is for dividing a scene into two.
D105(P)eng.book  58 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							59LSQT1040
Editing
Editing scenes
(RAM) (-RW‹VR›)
¬Rotate the mode dial to select  .
1 Press the MENU button, then select 
[ EDIT SCENE] # [ COMBINE] and press the 
joystick.
2 Select the scene to be combined, then press the 
joystick.
≥The selected scene and the next scene are combined.
≥If you wish to combine scenes that are not next to each other or scenes 
with different recording dates, first create a playlist and then combine the 
scenes on the playlist. 
(l61, 66)
3 When the confirmation message appears, select [YES], then press the 
joystick.
To continue combining other scenes
Repeat steps 2-3.
To complete editing
Press the MENU button.
Combining scenes
This function is only for combining two consecutive scenes into one.
D105(P)eng.book  59 ページ  ２００６年１月１６日　月曜日　午後４時１分 
						

							60LSQT1040
Editing
Using playlists
Using playlists
You can create a playlist by gathering your favorites from the recorded scenes.
Since the playlist is not created by copying data, you will consume little of the disc capacity by 
making a playlist.
≥If you create or delete playlists, the original scenes will not be modified. Editing scenes on a 
playlist will not affect the original scenes.
≥The maximum number of items on a disc (per side)
– Playlists: 99
– Playlist scenes: 999≥If original scenes are deleted, the portion of playlists 
created with these scenes is also deleted.
What is a playlist?
Recorded scenes
Playlist
D105(P)eng.book  60 ページ  ２００６年１月１６日　月曜日　午後４時１分