Home > Panasonic > Camera > Panasonic Vdr D105 Operating Instructions Manual

Panasonic Vdr D105 Operating Instructions Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Panasonic Vdr D105 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							31LSQT1040
    Setup
    Using the menu screen
    Using the menu screen
    Refer to “Menu list” (l78) for information about the menus.
    1 While stopped, press the MENU button.
    The menu displayed differs depending on the position of the mode 
    dial.
    ≥Do not switch the mode dial when the menu is displayed.
    2 Move the joystick up or down in order to 
    select the desired top menu A.
    3 Move the joystick right or press 
    the joystick.
    The submenu B is displayed.
    4 Move the joystick up or down in order to 
    select the submenu item.
    CCurrent settings on menus
    MENU
    A
    B
    C
    D105(P)eng.book  31 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    							32LSQT1040
    Setup
    Using the menu screen
    5 Move the joystick right or press 
    the joystick.
    6 Move the joystick up or down in order to 
    select the desired item.
    7 Press the joystick to enter the selection.
    To get back to the previous screen
    Move the joystick left.
    To exit the menu screen
    Press the MENU button.
    ≥The menu screen does not appear during recording 
    or playing. You cannot start other operations while 
    the menu screen appears.
    MENU
    D105(P)eng.book  32 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    							33LSQT1040
    Setup
    Setting date and time
    Setting date and time
    If the screen shows the incorrect date/time, then adjust it.
    ¬Rotate the mode dial to select  .
    1 Press the MENU button, then select [ BASIC] # 
    [ CLOCK SET] # [YES] and press the joystick.
    2 Move the joystick left or right to select the item to be 
    set. Then, move the joystick up or down to set the 
    desired value.
    ≥The year will change as follows:
    2000, 2001, ..., 2099, 2000, ...
    ≥The 12-hour system is used to display the time.
    3 Press the joystick to enter the selection.
    ≥After pressing the MENU button to finish the setting, check the date and time display.
    ≥The clock function starts at [00] seconds.
    ∫Changing the display style
    Press the MENU button, then select [ SETUP] # 
    [DATEFORMAT] # desired display style and press the joystick.
    ∫Changing the date and time display style
    Press the MENU button, then select [ SETUP] # [DATE/TIME] 
    # desired display style and press the joystick.
    ≥The date and time function are driven by a built-in 
    lithium battery.
    ≥Make sure to check the time before recording.
    ≥If [0] or [- -] is indicated when this unit is turned 
    on, then the built-in lithium battery runs down. After 
    charging the battery using the steps below, set the 
    clock.
    Connect the AC adaptor to this unit or place the 
    battery on this unit, and the built-in lithium battery 
    will be recharged. Leave this unit as is for approx. 
    24 hours, and the battery will save the date and time 
    for approx. 6 months. (Even if the OFF/ON switch is 
    set to OFF, the battery is still being recharged.)
    Display 
    styleY/M/D M/D/Y D/M/Y
    Screen 
    display3:30 PM
    2006.12.153:30 PM
    12.15.20063:30 PM
    15.12.2006
    [DATE] [D/T] [OFF]
      3:30 PM 
    12.15.200612.15.2006
    D105(P)eng.book  33 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    							34LSQT1040
    Setup
    Adjusting LCD monitor/viewfinder
    Adjusting LCD monitor/viewfinder
    Adjust the brightness and color level.
    1 Press the MENU button, then select [ SETUP] # 
    [ LCD SET] or [ EVF SET] # [YES] and press the 
    joystick.
    2 Move the joystick up or down to select the item to be 
    adjusted. Then, move the joystick left or right to 
    make the adjustment.
    The bar display moves.
    [ LCD SET]
    : Brightness of the LCD monitor
    : Color level of the LCD monitor
    [EVFSET]
    : Brightness of the viewfinder
    ≥In order to adjust the brightness of the viewfinder, 
    close the LCD monitor, and the viewfinder will be 
    activated.≥When the LCD monitor is rotated by 180° towards 
    the lens, the brightness of the LCD monitor cannot 
    be adjusted.
    ≥These settings will not affect the images actually 
    recorded.
    Adjust the focus by sliding the eyepiece corrector 
    knob.
    ≥You can adjust the brightness of the viewfinder from the menu. 
    (labove)
    EVF
    EVF
    EVF
    Adjusting the field of view
     3:30 PM
    12.15.2006 3:30 PM
    12.15.2006 3:30 PM
    12.15.2006 3:30 PM
    12.15.2006
    D105(P)eng.book  34 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    							35LSQT1040
    Recording
    Before recording
    Recording
    Before recording
    1Hold the camera with both hands.
    2Run your hand through the grip belt.
    3Do not cover the microphones or sensors with your hands.
    4Keep your arms near your body.
    5Slightly open your legs.
    ≥When you are outdoors, record pictures with the sunlight behind you. If the subject is backlit, it 
    will become dark in the recording.
    Basic camera positioning
    4
    5 1
    23
    D105(P)eng.book  35 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    							36LSQT1040
    Recording
    Recording motion pictures
    Recording motion pictures
    (RAM) (-RW‹VR›) (-RW‹V›) (-R)
    Record motion pictures onto a disc.
    1 Remove the lens cap, then turn the unit on.
    If the unit is turned on with the lens cap fitted, the automatic white balance adjustment may not 
    function properly.
    2 Rotate the mode dial to select  .
    3 Press the recording start/stop 
    button to start recording.
    To end the recording
    Press the recording start/stop button again to 
    pause recording.
    ≥[¥] and [;] are red during recording. Do not 
    move this unit until [;] is green.
    ≥The images recorded between pressing the recording start/stop button to start recording and 
    pressing it again to pause recording become one scene.
    ≥When about 5 minutes has passed without any operation, this unit automatically turns off to 
    prevent the battery from running down. When you use this unit, turn it on again.
    This setting can also be set to [OFF]. (l79, POWER SAVE)
    ≥The maximum number of scenes on a disc (per 
    side): 999 (Even if there is remaining capacity for 
    recording on a disc, you may not be able to record 
    999 scenes.)
    ≥While “WRITING THE INFORMATION ON THE 
    DISC.” is displayed, do not disconnect the AC cable 
    or remove the battery as doing so may make the 
    disc unusable.≥Sound is recorded in Dolby Digital from the internal 
    stereo microphone on the front of the unit. Take 
    care not to block this microphone.
    ≥Each time the unit enters the recording pause 
    mode, the counter display will be reset to 
    “0h00m00s”.
    D105(P)eng.book  36 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    							37LSQT1040
    Recording
    Recording motion pictures
    ARemaining time left for recording
    (When the remaining time is less than 1 minute, [R 0h00m] 
    flashes red.)
    BRecording mode
    CRecording time elapsed
    ≥While motion picture recording is in progress, do not 
    disconnect the battery or AC adaptor. If you do, a 
    repair disc message may be displayed when the 
    power is turned back on. (l83, About recovery)
    Press the MENU button, then select [ BASIC] # 
    [RECMODE] # desired item and press the joystick.
    This unit records in VBR. VBR is an abbreviation for Variable Bit Rate. VBR recording automatically 
    varies the bit rate (amount of data in a fixed time) depending on the subject being recorded. This 
    means if a subject with sharp movements is recorded, the recording time is reduced.
    ≥Mosaic-pattern noise may appear on a playback 
    image in the following cases.
    – When there is a complicated pattern in the 
    background
    – When the unit is moved too much or too fast
    – When a subject with sharp movements has been 
    recorded
    (Particularly if [ REC MODE] was set to [ ] 
    during recording.)
    Screen indications in the disc recording mode
    R 0h02mR 0h02mR 0h02m0h00m10s0h00m10s0h00m10sSPA
    B
    C
    Immediately after recording finishes the ACCESS/PC lamp lights. While it lights, the disc is 
    rotating and disc information is being recorded. If you run while holding the unit or swing it, the 
    recorded images may be distorted so do not strongly shake or cause impact to it.
    Changing the recording mode of the motion picture
     
    Recording modes and recordable time available for the motion picture
    Recording modeRecordable time
    (on single side)
    XP(High quality) Approx. 18 min Image quality prioritized
    SP(Normal) Approx. 37 min
    LP(Long play) Approx. 75 min Recording time prioritized
     LP
    D105(P)eng.book  37 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    							38LSQT1040
    Recording
    Various recording functions
    Various recording functions
    (RAM) (-RW‹VR›) (-RW‹V›) (-R)
    You can zoom in up to 30k optically.
    ¬Rotate the mode dial to select  .
    Move the zoom lever.
    ≥When zooming in while holding this unit by hand, 
    we recommend using the image stabilizer function. 
    (l45)
    ≥When distant subjects are brought closer, they are 
    focused at about 1.3 m (4.3 feet) or more.≥When the zoom magnification is 1k, this unit can 
    focus on a subject approx. 2 cm (0.8z) away from 
    the lens. (Macro function)
    ≥The zoom speed varies depending on the range 
    over which the zoom lever is moved.
    ≥When the zoom speed is high, the subject may not 
    be focused easily.
    (RAM) (-RW‹VR›) (-RW‹V›) (-R)
    If the zoom magnification exceeds 30k, then the digital zoom function will be activated. The 
    maximum magnification provided by the digital zoom can be switched.
    ¬Rotate the mode dial to select  .
    Press the MENU button, then select [ ADVANCED] # 
    [D.ZOOM] # desired item and press the joystick.
    ≥The larger the digital zoom magnification, the more 
    the image quality is degraded.
    Zoom in/out function
    T side:To bring distant people or objects appear closer 
    for recording (zoom in)
    W side:To make sights appear more distant for 
    recording (zoom out)
    Digital zoom function
    [OFF]: Optical zoom only (Up to 30k)
    [50k]: Up to 50k
    [1000k]: Up to 1000k
    D105(P)eng.book  38 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    							39LSQT1040
    Recording
    Various recording functions
    (RAM) (-RW‹VR›) (-RW‹V›) (-R)
    Interlocked with the zooming operation, the microphone will collect sounds clearly far away with the 
    tele-shot or those in the vicinity with the wide-angle shot.
    ¬Rotate the mode dial to select  .
    Press the MENU button, then select [ ADVANCED] # 
    [ ZOOM MIC] # [ON] and press the joystick.
    (RAM) (-RW‹VR›) (-RW‹V›) (-R)
    You can record yourself while viewing the LCD monitor. You can record persons in front of the unit 
    while showing them the image. The image is horizontally flipped as if you see a mirror image. 
    (However the image recorded is the same as a normal recording.) 
    ¬Rotate the mode dial to select  .
    Rotate the LCD monitor towards the lens side.
    ≥When the LCD monitor is opened, the viewfinder automatically turns 
    off. However if the LCD monitor is then rotated towards the lens side, 
    the viewfinder is activated.
    ≥When the LCD monitor is rotated towards the lens side, the icon will 
    not be displayed even if you press the joystick.
    ≥Only some indications will appear on the screen. When [°] appears, 
    return the direction of the LCD monitor to normal position and check the warning/alarm indication. 
    (l82)
    To use the zoom microphone function
    Recording yourself
    D105(P)eng.book  39 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    							40LSQT1040
    Recording
    Various recording functions
    (RAM) (-RW‹VR›) (-RW‹V›) (-R)
    This is more effective if you record the bust image of a person.
    ¬Rotate the mode dial to select  .
    1 Press the joystick to display the icon shown in the 
    illustration.
    2 Move the joystick down to select [ ].
    To cancel the soft skin mode
    Select [ ] again.
    ≥If the background or anything else in the scene has 
    colors similar to the skin color, they will also be 
    smoothed.≥If the brightness is insufficient, the effect may not be 
    clear.
    Soft skin mode
    This makes skin colors appear softer for a more attractive appearance.
    D105(P)eng.book  40 ページ  2006年1月16日 月曜日 午後4時1分 
    						
    All Panasonic manuals Comments (0)

    Related Manuals for Panasonic Vdr D105 Operating Instructions Manual