Panasonic Up/Down Wall Mount Kit, Up/Down Stand Kit UE-608030, UE-608031, UE-608032 Operating Instructions

Wall Mounting Construction21
Installation Manual
Notice
•Ensure that the installation strength is at least as great as the 
specified pull-out strength of the anchors which is 5,197.5 N 
[530 k gf].
•Use the values recommended by the manufacturer of the anchors 
used for the depth to which the anchors are to be embedded in the 
wall.
•Use M8 bolts when the anchors have internal screw threads.
•Ensure that the length of the M8 bolts provides an interfitting length 
of at least 1.5 times the bolt diameter....

Wall Mounting Construction
22 Installation Manual

If the wall backing materials are not principal structural components, they must be reinforced as below. Install 
the reinforcing material onto the wall backing materials. If the distance between the wall backing material is 
not less than 910 mm (2 ft. 11
13/16in.), use a material whose strength is equivalent to the backing materials 
and add extra backing materials so that the distance is made less than 910 mm (2 ft. 1113/16in.).
*Use a material whose...

Wall Mounting Construction23
Installation Manual
III.When the Principal Structural Components are in Close Proximity to the Wall Backing Materials 
(when there is no distance between the backing materials and principal structural components)
•Dimension “X” must not be more than 170 mm (611/16in.). If this maximum is exceeded, consult with a 
building contractor and take the steps to ensure that the reinforcing work at least equivalent to what was 
described in sections I and II above is carried out....

Wall Mounting Construction
24 Installation Manual
Mounting and Securing 
the Up/Down Unit
1Hang the up/down unit on the wall again.
2Take the steps below to secure the up/down unit.
1Pass one M8 bolt through the bottom hole in 
the stay L75 pipe on the left, and use it to 
secure the up/down unit.
2Pass another M8 bolt through the bottom 
hole in the stay drum 75 pipe on the right, 
and use it to secure the up/down unit.
3Tighten the M8 bolts in the top holes of the 
left and right pipes, and fasten the...

Wall Mounting Construction25
Installation Manual
Notice
•When mounting a projector other than a SANYO 
model onto the projector bracket, mount it with the 
adjustment feet on the bottom of the projector 
retracted.
•Follow the steps below to mount a SANYO model.
1Extend the two adjustment feet by pulling them 
out.
2Pass the adjustment feet through hole A in the 
projector bracket.
3Move the projector bracket, move the adjustment 
feet of the projector to the positions shown in the 
figure below, then...

Wall Mounting Construction
26 Installation Manual
3Align the projector sub-bracket so that the 
projector fits in between, and secure both ends 
using the toothed washers (J) and the screws 
( D) for securing the projector sub-bracket.
Notice
•Align the projector sub-bracket so that it supports 
the projector, leaving no gaps. Fasten the sub-
bracket securely to the projector on both sides 
using the toothed washers ( J
) and screws ( D
) 
for securing the projector sub-bracket.
4Attach the screw ( F)...

Wall Mounting Construction27
Installation Manual
•The position where the knob is to be secured 
depends on the projector which is going to be 
used.
Notice
•Keep the other knob for future use. After all 
installation work is finished, attach the knob to an 
empty hole on the board bracket ( 7
) on the back 
of the board.
 
3Insert the projector arm from above into the 
pipe holding post of the up/down frame.
•Introduce the ends of the power cable and video 
cable which have already been passed through...

Wall Mounting Construction
28 Installation Manual
6Route and connect the power cable and video 
cable, which have already been passed 
through the projector arm, to the projector, and 
secure the pipe cap (G) using the screw (H) 
for securing the pipe cap.
7Attach cable holder A  (1)
 to the center wall side of 
the lift bottom stay, and route the power cable and 
video cable so that they point straight down.
•Use cable holder B  (
2
)
 for cable management of 
the elite Panaboard and other equipment....

Wall Mounting Construction29
Installation Manual
1Loosely secure the board bottom bracket to 
the position shown below.
•In the state the UB-T880 is shipped, the position 
where the board bottom brackets are secured is 
appropriate when using the SANYO 
LP-WXL46(S). The position where the bottom of 
the elite Panaboard is to be secured differs 
depending on the type of elite Panaboard to be 
installed.
Note
•The position at which the board bottom bracket is to 
be fixed applies to the SANYO LP-WXL46(S)...

Wall Mounting Construction
30 Installation Manual
Notice
•Even when the elite Panaboard has been placed 
on the up/down unit, it has still not been secured 
in place. If any attempt is made to lift the elite 
Panaboard in this state, it may become 
disengaged from the up/down unit so do not lift it 
until it has been secured loosely.
3Loosely secure the elite Panaboard to the up/
down unit
•Remove the lower frame cover centered at the 
bottom of the elite Panaboard. Align the wall 
mount holes on the...