Panasonic UF 8100 YC User Manual

71
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
4.2. Service Modes (For Facsimile)
Caution:
The factory default parameters are preset (country dependent) for optimum performance and in 
compliance with the local telecommunication regulations/standards, and do not need to be changed. 
Changing some of these parameters may cause the unit to be no longer compliant or become 
inoperable.
4.2.1. Fax Service Mode Procedure
1. To enter the Fax Service Mode
a. Press “FUNCTION” and then “7” keys.
b. Press...

72
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
4.2.3. Fax Service Mode 1 (Function Parameter Setting)
Use the following procedure to change the function parameters.
Enter the desired code number and press “START” key.
↓
If you wish to select another code number, scroll the menu with the “V”, ”/\” arrow keys.
↓
Select the desired function code and press the START key.
↓
When the “CLEAR” key is pressed, the selected code input will not be accepted.
↓
Press “STOP” key, then press “FUNCTION” and “CLEAR”...

73
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
005Destination Code
(UF-7100/8100 
only)000 : Austria
001 : U.K.
002 : Canada
003 : Denmark
004 : Taiwan
005 : Finland
006 : Germany
007 : Netherlands
008 : Italy
009 : Spanish
010 : Hong Kong
011 : Australia
012 : Switzerland
013 : Norway
015 : Portuguese
016 : Ireland
017 : Belgium
018 : Sweden
019 : Turkey
020 : U.S.A.
021 : France
022 : New Zealand
025 : Japan
029 : Poland
030 : Czech
031 : Russia
032 : Greece
033 : Hungary
034 : Indonesia
035 :...

74
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
011 RX Level 1 = -43 dBm
2 = -38 dBm
3 = -33 dBm
4 = -48 dBmSelects the receiving sensitivity of -33/-38/-43/-48 
dBm.
012 DTMF Level 00 = 0 dBm
~
15 = -15 dBmSelects the DTMF output level, 0 to -15 dBm in 1 
dBm steps.
013 G3 RX EQL 1 = 0dB
2 = 4dB
3 = 8dB
4 = 12dBSelects the cable equalizer for G3 reception mode, 
0dB, 4dB, 8dB or 12dB.
014 G3 TX EQL 1 = 0dB
2 = 4dB
3 = 8dB
4 = 12dBSelects the cable equalizer for G3 transmission 
mode, 0dB, 4dB, 8dB or...

75
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
025 COMM. Start-Up 1 = First
2 = SecondSelects the communication start-up condition (XMT 
and Polling).
(Used when Echo Suppression is disabled.)
026 Non-Standard 1 = Off (Invalid)
2 = On (Valid)Selects own mode (Panafax mode).
027 Short Protocol B 1 = Off (Invalid)
2 = On (Valid)Selects the short protocol mode.
028 Short Protocol D 1 = Off (Invalid)
2 = On (Valid)Selects the short protocol mode. When activated, it 
allows the machine to automatically...

76
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
044 Redial Count 0 = no redial
~
15 = 15 times
0 ~ 9 (For Australia Only)Selects the redial count from 0 to 15 times in 1 step 
intervals.
Note:
In order to comply with the TBR21 requirement 
for the EC destinations, do not select 15 times.
045 Ring Detect 
Count1 = 1 ring
~
9 = 9 ringsSelects the ring detection count from 1 to 9 rings in 
1 ring step intervals.
046 On-Hook Time 0 = 0 sec.
~
90 = 90 sec.Selects the on-hook time between sequential...

77
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
068 NYSE Fax 
Forward
(USA and Canada 
Only)1 = Off
2 = OnSelects whether the machine will forward the 
incoming and outgoing faxes to a specified station.
Note:
Once this parameter is activated, Fax 
Forwarding via Fax Parameter 054 is 
automatically disabled, an Access Code of 
0000 is automatically assigned and Fax 
Parameter 038 has a new setting added called 
NYSE.
069 NYSE Local Print
(USA and Canada 
Only)1 = Inc
2 = On (Always)Selects the...

78
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
082 JAM Length 1 = 1 m
2 = 2 mSelects the maximum length of the original that can 
be scanned.
083 Not Used
084 Line As No Paper 1 = Ring (ring)
2 = Busy (keep line busy)Selects whether to ring or send a busy tone to the 
remote station when the recording paper runs out or 
the unit cannot receive because of any trouble.
085~
086Not Used
087 Darker Level 0 = Lightest Contrast
~
15 = Darkest ContrastSelects the contrast level.
0←             →15
Lightest←...

79
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
Note 1: Continuous Polling (Station Mode)
This feature allows you to Store or Add documents into a Polled file in memory. 
To enable the Continuous Polling feature set the Function Parameter No. 003 to 2:STN 
(Station).
Depending on the setting of the User Parameter (Facsimile) No. 119: QWERTY KEYBOAD, 
one of the following operations is available:.
1. One-Touch
The upper 40 (40↑) Key is reserved for Store 4 Polling function, and cannot be changed.
To...

80
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
Note 4: The default setting of parameters depends on the country’s specifications or regulations. Print the 
Function Parameter List to confirm the default settings.
Note 5: 200 Series Function Parameters Only appear when the G3 Communications Port Kit is installed 
and follow the same numbering order.
Downloaded From ManualsPrinter.com Manuals