Panasonic System Controller Wv Cu161 Operating Instructions

							21
ERROR1
(2) Upload Setting
1. Display the PRESET DATA LOAD menu.
2. Select a camera number between CAM1 and CAM8 by
moving the joystick up or down.
3. Press the PRESET/SET/PROGRAM PRESET button.
4. The camera number and upload menu appear on the
monitor as shown below.
5. Select UP LOAD by moving the joystick up or down.
6. Press the PRESET/SET/PROGRAM PRESET button.
Uploading starts.
   CAM1:
    DOWN LOAD
    UP   LOAD
    DATA TITLE
    END 
LOADINGBlinking
7. While uploading, the word LOADING appears on the
right.
changing to 
Pin the progress bar indicates the
progress of uploading.
8. When uploading is completed, END appears on the
right. The progress bar disappears.
Notes:
•The preset data of up to 8 cameras can be uploaded.
•Uploading time is approx. 2 minutes per camera. When
uploading is completed, the combination camera such
as WV-CS854, WV-CS654 or WV-CS604 will move to the
Preset Position.
•Upload only preset data. 
Make any other settings from the Camera Setup menu.
•The camera picture may change as a result of upload-
ing data.  Access the Camera Setup menu to make the
necessary settings.
•Any previous preset data is overwritten by the uploaded
data.
•To terminate uploading, press the HOME/ESC button
while uploading. ERROR 3 appears. The progress bar
disappears.
•END and error messages remain on the menu until the
next operation is performed.Message Cause Note
IncompatibilityIncompatibility detected
between transmission
data and camera model
while uploading.
ERROR 3 Causes except
aboveUploading not possible
for some reason other
than the above.
   CAM1:
    DOWN LOAD
    UP   LOAD
    DATA TITLE
•In case of RS-485 Site Communication mode, check
that the unit address is the same as set on the combi-
nation camera. If the numbers do not agree, the camera
cannot be operated.
Therefore, preset data cannot be uploaded.
•Error Display 
When an error occurs during uploading, the following
messages appear on the monitor.
(3) Data Title Setting
1. Display the PRESET DATA LOAD menu.
2. Select the desired CAM1-CAM8 position by moving the
joystick up or down.
3. Press the PRESET/SET/PROGRAM PRESET button.
4. The camera number and data title menu appear on the
monitor as shown below.
   CAM1:
    DOWN LOAD
    UP   LOAD
    DATA TITLE
5. Select DATA TITLE by moving the joystick up or down.
The DATA TITLE menu appears as shown below.
   CAM1:
     0123456789
     ABCDEFGHIJKLM
     NOPQRSTUVWXYZ
     ().,’”:;&#!?=
     +-*/%$
    SPACESelected Character 
Area
Character Area
Space
6. Move the cursor to the desired character in the charac-
ter area by moving the joystick upward, downward,
right or left.
7. Press the PRESET/SET/PROGRAM PRESET button.
8. Repeat procedure 6 to 7 until all characters are edited. 
Up to 12 characters can be selected. 
						

							22
9. To return to the preset data menu, press the
HOME/ESC button after completing the data title set-
ting. 
To replace a specific character
1. Use the joystick to shift the cursor to the selected char-
acter area.
2. Move the cursor to the character to be replaced by
moving the joystick right or left.
3. Move to shift the cursor to the character area by moving
the joystick up or down, and move the cursor to the
desired character by moving the joystick up, down,
right or left.
4. Press PRESET/SET/PROGRAM PRESET button.
The selected character is replaced with the corrected
character area.
To delete a specific character
A character is deleted by inserting a blank space.
1. Use the joystick to shift the cursor to the selected char-
acter area.
2. Move the cursor to the character to be deleted by mov-
ing the joystick right or left.
3. Move the cursor to the SPACE position by moving the
joystick up or down.
4. Press the PRESET/SET/PROGRAM PRESET button.
[•] (space mark) appears in place of the deleted char-
acter.
     COMMUNICATION
   UNIT ADDRESS 1
   BAUD RATE    19200
   DATA BIT     8
   PARITY CHECK NONE
   STOP BIT     1
   WAIT TIME    OFF
   DELAY TIME   OFF
   XON/XOFF     NOT USE
(1) Unit Address Setting
This item lets you set a unit address that is set to the cam-
era for RS-485 communication. After confirming the unit
address that is set to the camera, set it up.
1. Display the COMMUNICATION menu.
2. Select UNIT ADDRESS by moving the joystick up or
down.
3. Select the unit address assigned to the combination
camera in the range of 1 to 96 by moving the joystick to
the right or left.
The initial factory setting is 1.
Note:If the unit address is not the same, the camera can-
not be operated.
(2) Baud Rate Setting
This item lets you set the baud rate for RS-485 communica-
tion.
1. Display the COMMUNICATION menu.
2. Select BAUD RATE by moving the joystick up or down.
3. Select 19200, 9600, 4800 or 2400 bps for the baud rate
by moving the joystick to the right or left.
The initial factory setting is 19200 bps.
Notes:
•At a baud rate of 2400 bps, the data response may be
unstable when an alarm is reset, for example.
•This setting must be compatible with the peripherals
connected.
(3) Data Bit Setting
This item lets you set the number of the data bits for RS-485
communication.
1. Display the COMMUNICATION menu.
2. Select DATA BIT by moving the joystick up or down.
3. Select 7 or 8 bit for the number of data bits by moving
the joystick to the right or left.
The initial factory setting is 8 bit.
Note:This setting must be compatible with the peripherals
connected.
Communication Setting
Note:The COMMUNICATION menu appears when the
Data Switch is set to RS-485. 
						

							23
(4) Parity Check Setting
This item lets you set the parity bit for RS-485 communica-
tion.
1. Display the COMMUNICATION menu.
2. Select PARITY CHECK by moving the joystick up or
down.
3. Select NONE, EVEN or ODD for parity check by moving
the joystick to the right or left.
The initial factory setting is NONE.
Note:This setting must be compatible with the peripherals
connected.
(5) Stop Bit Setting
This item lets you set the number of stop bits for RS-485
communication.
1. Display the COMMUNICATION menu.
2. Select STOP BIT by moving the joystick up or down.
3. Select 1 or 2 for the number of stop bits by moving the
joystick to the right or left.
The initial factory setting is 1 bit.
Note:This setting must be compatible with the peripherals
connected.
(6) Wait Time Setting
This item lets you set the waiting time in milli-seconds (ms)
till retry for RS-485 communication.
1. Display the COMMUNICATION menu.
2. Select WAIT TIME by moving the joystick up or down.
3. Select OFF, 100, 200, 400, or 1 000 ms for the wait time
by moving the joystick to the right or left.
The initial factory setting is OFF (No retry).
(7) Delay Time Setting
This item lets you set the lowest delay time from the recep-
tion of data to reply for RS-485 communication.
1. Display the COMMUNICATION menu.
2. Select DELAY TIME by moving the joystick up or down.
3. Select OFF, 20, 40, or 100 ms for the delay time by
moving the joystick to the right or left. 
The initial factory setting is OFF.
(8) XON/XOFF Setting
This item lets you set flow control for RS-485 communica-
tion.
1. Display the COMMUNICATION menu.
2. Select XON/OFF by moving the joystick up or down.
3. Select NOT USE or USE mode for XON/XOFF by mov-
ing the joystick to the right or left. 
The initial factory setting is NOT USE. 
						

							24
CAMERA CONTROL FUNCTIONS
It is necessary to setup the camera before using the cam-
era control functions. For further information, refer to the
Operating Instructions for the respective combination cam-
era (See page 30). You can also set it up from Camera
Setup menu if you operate a system.
Pan/Tilt Control
The following function is available with a combination cam-
era or pan/tilt head.
Move the pan/tilt head in the desired direction using the
joystick.
The camera can be moved in eight directions.
To move the pan/tilt head slowly, move the joystick while
holding down the SLOW/CAMERA FUNCTIONbutton.
Note:The SLOW/CAMERA FUNCTION button cannot be
used in the camera or pan/tilt head which is not provid-
ed with 8-steps speed.
OPERATING PROCEDURES
ª
” ¶E
Joystick 
Lens Control
The following functions are available with cameras provided
with controllable lens.
1. Press the FOCUS NEARor FOCUS FARbutton to
adjust the lens focus while watching the monitor.
NEAR FAR
FOCUS
AUTO FOCUS
If you are using a camera with an auto focus feature,
the lens focus can be automatically adjusted by press-
ing the FOCUS NEARand FOCUS FARbuttons simul-
taneously.
2. Press the ZOOM TELEbutton to optically bring the
object closer, or press the ZOOM WIDEbutton to opti-
cally widen the scene.
WIDE TELE
IRIS ZOOM
CLOSE OPENIRIS RESET
Focal length differs depending on the lens installed on
the camera.
3. Press the SHIFTbutton.
SHIFT
4. Press the ZOOM/IRISbuttons to adjust the lens focus
while watching the monitor.
If the IRIS CLOSEand IRIS OPENbuttons are pressed
for approx. 1 sec. or more simultaneously, the iris is
reset to the default.
WIDE TELE
IRIS ZOOM
CLOSE OPENIRIS RESET 
						

							25
Operation of Combination Camera
It is necessary to setup the combination camera before
operating it. For further setup information, refer to the
Operating Instructions for the combination camera (See
page 30). You can also set it up from the Camera Setup
menu if you operate a system.
Changing to Picture at Preset Position
The following function is available only with cameras pro-
vided with the preset function.
The preset function makes the combination camera move
to the programmed preset position.
It is necessary to program preset positions for the combina-
tion camera beforehand.
Select a preset number using the numeric buttons, and
press the PRESET/SET/PROGRAM PRESETbutton.
Auto Pan
The following functions are available only with cameras pro-
vided with the pan/tilt head specified for this operation.
It is necessary to program auto pan function for the combi-
nation camera beforehand.
1. Press the AUTO/B/W/PATROL STOPbutton.
The auto panning function programmed for the combi-
nation camera is activated.
The picture appears on the monitor.
The following functions differ depending on the combi-
nation camera.
AUTO PAN ON or functions set in the combination
camera:
Press Numeric button 1 followed by this but-
ton.
AUTO SORT ON:Press Numeric button 2 followed by
this button.
AUTO SEQ ON:Press Numeric button 3 followed by
this button.
RANDOM PAN ON:Press Numeric button 4 followed
by this button.
For further information, refer to the Operating Instruc-
tions for the combination camera.
2. To stop auto pan, move the joystick.
PROGRAM
PRESETSET PRESET
The combination camera moves to the programmed preset
position, and the picture of the camera in that position
appears on the monitor.
Changing to Picture at Home Position
The following function is available only with cameras pro-
vided with the preset function.
It is necessary to program the home position for the combi-
nation camera beforehand.
Press the HOME/ESCbutton to move the combination cam-
era to the home position.
ESC HOME
The camera returns to the home position and the picture at
that position appears on the monitor.
B/W AUTO
PATROL STOP
UP
LR
DOWN
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET 
						

							26
Changing from Color to Black and White
Picture
The following function is available with cameras provided
with the color-black and white switching function specified
for this operation.
1. Press the AUTO/B/W/PATROL STOPbutton, after
pressing the SHIFT button, to change from color to
black and white picture. The black and white picture
appears on the monitor.
Camera Patrol Function
The following function is available with combination cam-
eras provided with the camera patrol function.
The camera patrol function enables the combination cam-
era to learn joystick movements and zooming operation.
To program the camera patrol learning function, see page
31.
1. Press the PATROL PLAY/PATROL LEARNbutton to
move the combination camera according to the data
saved in the memory.
The camera patrol picture appears on the monitor.
2. To stop the patrol play function, move the joystick.
PATROL
PLAY
PATROL LEARN
Camera Functions
The following functions are available with the combination
camera. Those camera functions can be called up by num-
bers.
For further information, refer to the Operating Instructions
for the camera. Examples of camera functions are
described as below.
•Super Dynamic 
2
The following function is available only with cameras
provided with the Super Dynamic 2function.
1. Press numeric buttons 8and 4.
UP
LR
DOWN
B/W AUTO
PATROL STOP
SHIFT
2. To change back from black and white to color picture,
press the AUTO/B/W/PATROL STOPbutton after pres-
sing the SHIFTbutton.
B/W AUTO
PATROL STOP
SHIFT
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET
2. Press the SLOW/CAMERA FUNCTIONbutton after
pressing the SHIFTbutton.
SHIFT
SLOW
CAMERA
FUNCTION
3. To cancel the Super Dynamic 2function, press numer-
ic buttons 8and 5.
•Electronic Shutter
The following function is available only with cameras
provided with the electronic shutter feature.
1. Press numeric buttons 1, 7and 1.
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET
Notes:
•This function is disabled if the change to black and
white picture function is set to AUTO in the Camera
Setup menu.  In case of using this function, change the
parameter in the Camera Setup menu.
•It is invalid unless this operation of the color-black and
white switching function is completed in the camera
side. 
						

							27
3. To cancel the electronic shutter function, press numeric
buttons 1, 7and 2.
4. To increase electronic shutter speed, press numeric
buttons 1, 7and 3.
5. To decrease electronic shutter speed, press numeric
buttons 1, 7and 4.
•Automatic Gain Control
The following function is available only with cameras
provided with the AGC feature.
1. Press numeric buttons 1, 7and 5.2. Press the SLOW/CAMERA FUNCTIONbutton after
pressing the SHIFTbutton.
3. To cancel the electronic sensitivity function, press
numeric buttons 1, 7and 8.
4. To increase electronic sensitivity, press numeric but-
tons 1, 7and 9.
5. To decrease electronic sensitivity, press numeric but-
tons 1, 8and 0.
•Camera Restart
The following function is available only with cameras
provided with the camera restart function.
1. Press numeric buttons 1, 0and 0.
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET
2. Press the SLOW/CAMERA FUNCTIONbutton after
pressing the SHIFTbutton.
SHIFT
SLOW
CAMERA
FUNCTION
3. To cancel the AGC function, press numeric buttons 1, 7
and 6.
SHIFT
SLOW
CAMERA
FUNCTION
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET
2. Press the SLOW/CAMERA FUNCTIONbutton after
pressing the SHIFTbutton.
SHIFT
SLOW
CAMERA
FUNCTION
SHIFT
SLOW
CAMERA
FUNCTION
2. Press the SLOW/CAMERA FUNCTIONbutton after
pressing the SHIFTbutton.
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET
•Electronic Sensitivity Enhancement
The following function is available only with cameras
provided with the electronic sensitivity function.
1. Press numeric buttons 1, 7and 7. 
						

							28
External Device Control
Auxiliary Control
The following function is available only in cases where
external devices are connected to the receiver or the cam-
era.
1. Press the WIPER/AUX1or DEF/AUX2button after
pressing the SHIFTbutton, to enable or the user switch
on the receiver. 
The AUX1or AUX2indicator lights up.
Camera Housing Control
Wiper Control
The following function is available only with the cameras
whose housing is provided with the wiper control function.
1. Press the WIPER/AUX1button to operate the wiper on
the selected camera.
The DEFindicator lights up.
2. To cancel the defroster control function, press the
DEF/AUX2button.
The DEFindicator goes off.
AUX1 WIPER
The WIPERindicator lights up.
2. To cancel the wiper control function, press the WIPER/
AUX1button.
The WIPERindicator goes off.
Caution:To prevent early wiper wear, be sure to turn off
the wiper whenever it is not needed, or before selecting
another camera for viewing.
Defroster Control
The following function is available only with the cameras
whose housing is provided with the defroster control func-
tion.
1. Press the DEF/AUX2button to operate the defroster for
the selected camera.
AUX2DEF
SHIFTAUX1 WIPER
AUX2DEF
2. To cancel the auxiliary control function, press the
WIPER/AUX1or DEF/AUX2button after pressing the
SHIFTbutton.
The AUX1or AUX2indicator goes off. 
						

							29
ALARM CONTROL FUNCTIONS
When the WV-CU161 receives an alarm signal from a cam-
era site, an alarm is activated. The WV-CU161 can handle
the following alarms.
Camera Site Alarm
Coaxial Multiplex Communication:
Alarm is multiplexed with video signals from the cam-
era.
RS-485 Site Communication
Alarm is transmitted via RS-485.
Terminal Alarm
Alarm is input via the alarm input terminal on the rear
panel from external devices such as a sensor.
Alarm Operation
When the alarm signal is supplied in the Alarm On mode,
[ALARM] appears on the monitor screen.
RESET
SUSPENDALARM
The alarm indicator starts to blink and the buzzer sounds.
(ALARM BUZZER is preset to OFF at the factory.)
Character display
(ALARM DISPLAY ON)
ALARM
The alarm indicator goes off, [ALARM] disappears from the
monitor screen, and alarm is reset.
Alarm Suspend
The alarm suspension function allows you to suspend alarm
while setting up the camera or the WV-CU161.
1. Press ALM RESET/SUSPENDbutton after pressing the
SHIFTbutton.
The ALM SUSPENDindicator lights up.
Alarm Reset
Manual or Automatic resetting can be selected.
When the alarm is reset, [ALARM] disappears from the
monitor screen and the alarm reset signal is output from the
alarm terminal on the rear panel.
Automatic Reset
The alarm is reset automatically after the programmed
alarm output time has elapsed.
The alarm indicator changes from blinking to steady light,
and [ALARM] disappears from the monitor screen.
To turn off the steady light, press the ALARM RESET/SUS-
PEND button.
Note:Alarm can also be reset by input of the alarm recover
signal (no-voltage contact) from the alarm recover
input. The reset mode in this case is the same as auto-
matic reset.
Manual Reset
Press the ALARM RESET/SUSPENDbutton.
RESET
SUSPENDALARM
SHIFT
Alarm input is ignored even after the ALM SUSPEND
has been set.
2. To cancel the alarm suspend function, press the ALM
RESET/SUSPENDbutton after pressing the SHIFTbut-
ton.
The ALM SUSPENDindicator goes off. When the preset number is set at ALARM PRESET or
ALARM TERMINAL parameter in ALARM SETUP menu, the
camera aims the preset position while an alarm is activated.
The alarm signal continues to be output to external devices
from the alarm output connector until the alarm is reset.
Notes:
•Alarm display On/Off and Buzzer On/Off mode can be
selected. (See page 18)
•The camera or receiver control can be continued even
when an alarm is supplied.
OPERATE ALARM
ALARM
Blinking: Alarm has been activated.
Light on: Alarm has been reset automatically
, 
or by input signal from external devices 
(when the alarm switch is in the upper position).
Light off: Alarm has been reset manually, or the 
ALARM RESET/SUSPEND button has
been pressed while the alarm indicator is on. 
						

							30
CAMERA SETUP
You can use the WV-CU161 to setup the camera from the
Camera Setup menu.
For further information, refer to the Operating Instructions
for the individual combination cameras.
Camera Setup
1. Press the CAMERA SETUP/SETUP/PROGRAMbutton
for 2 seconds or more to access the Camera Setup
menu. The CAMERA SETUPindicator lights up.
CAMERA
SETUP
SETUP
PROGRAM
5. Press the CAMERA SETUP/SETUP/PROGRAMbutton
for 2 seconds or more to complete the Camera Setup. 2. Select an item and parameter by pressing numeric but-
tons 2, 4, 6and 8.
3. Press the PRESET/SET/PROGRAM PRESETbutton to
execute the parameter or enter a submenu.
   *** SET UP MENU ***
PRESET 1*
 MAP 
 HOME POSITION
 SELF RETURN
 AUTO MODE
 AUTO PAN KEY
 DIGITAL FLIP
 LOCAL/REMOTE
 SPECIAL1
CAMERA
RS485 SET UP15
10MIN
AUTO PAN
SEQ
OFF
LOCAL
(Example of Camera Setup menu)
CAMERA
SETUP
SETUP
PROGRAM
123
46
789
0
5
PROGRAM
PRESET ESC HOME
SET PRESET
PROGRAM
PRESETSET PRESET
4. To return to the previous menu, press the HOME/ESC
button.
ESC HOME
Notes:
•To display the special menu, move the cursor to [SPE-
CIAL] on the Setup menu, and press numeric buttons 4
and 6simultaneously for 2 seconds or more.
•To restore all defaults, move the cursor to [CAMERA
RESET]* on the Setup menu, and press buttons 4, 5
and 6simultaneously for 2 seconds or more.
* The menu to restore the camera defaults differs
depending on the camera:
[SPECIAL] for the WV-CS654, [SPECIAL 2] for the WV-
CS854, and [END] for fixed cameras, etc.
Caution:If camera setup is started using the buttons
on the camera, all future operations for setup must
be performed with buttons.
If camera setup is started using the System
Controller, all future operations for setup must be
performed using the same controller.
Note:For further information, refer to the Operating
Instructions for the selected camera.
Keys Used in Camera Setup Menu
CAMERA SETUP/SETUP/PROGRAM button:
To display a program menu by pressing CAMERA
SETUP/SETUP/PROGRAM button 2 seconds or more.
CAMERA
SETUP
SETUP
PROGRAM
CAMERA SETUP/SETUP/PROGRAM button:
To enter a submenu.
CAMERA
SETUP
SETUP
PROGRAM
HOME/ESC button:
To return to the previous menu.
ESC HOME
Numeric buttons:
To move the cursor.
To select modes.
28
4
6