Panasonic Remote Camera Controller Aw Rp120 Operating Instructions

21
6 . Press START button [11] .The tracing memory is recalled and the remote camera starts 
moving .
T M 0 3 : 0 m 2 0 s  N   T
R e s t o r i n g. . .
Current recall position Total time of tracing memory 
during recalling
7 . Operate one of the PAN/TILT lever, ZOOM button, 
FOCUS dial, IRIS dial, and white balance mode selection 
buttons to make a correction
 .
Overwriting is performed from the point in time that the correction 
operation is performed .
zzIt is not possible to correct just an...

22
Configuring the remote camera operation settings
Adjusting the operation speed of the pan, 
tilt, zoom, and focus
The dedicated dials can be used to individually adjust the operation 
speed of the remote camera for each of the PAN/TILT lever, ZOOM 
button, and FOCUS dial operations performed with the unit .
ZOOM SPEED dial
FOCUS SPEED dial PAN/TILT SPEED dial
„„Operation of SPEED dial
Turned clockwise :
Operation is at a higher speed (HI)
Turned counterclockwise : Operation is at a lower...

23
Setting the pan, tilt, zoom, and focus 
operation directions
You can set the direction that a remote camera moves in response to 
the operation of the PAN/TILT lever, ZOOM button, and FOCUS dial .
With this unit, you can set the direction for each camera number .
Setting the panning direction
Set the operation of the remote camera in the horizontal direction in 
response to the horizontal operation of the PAN/TILT lever .
1 . Press the MENU button .
2 . Open PAN DIRECTION menu [26] .
3 . Turn the F1...

24
Setting the focusing direction
Set the focusing operation of the lens in response to the operation of the 
FOCUS dial .
1 . Press the MENU button .
2 . Open FOCUS DIRECTION menu [29] .
3 . Turn the F1 dial to display the camera number for which 
to configure the setting  .
1 . C A M 1          
                  N O R M A L
4 . Turn the F2 dial to select “NORMAL” or “REVERSE”, 
and then press the F2 dial to confirm the selection  .
NORMAL :The focus moves toward the far end when the FOCUS 
dial is...

25
Setting the movement ranges (limiter 
function) of a remote camera
Depending on the installation location, there may be an obstruction in 
a movement range of a remote camera, and the remote camera may 
come into contact with that obstruction when the pan or tilt operation is 
performed .
A

 malfunction or accident may occur if the remote camera comes into 
contact with the obstruction so you need to set a limiter in front of the 
obstruction to prevent contact
 .
Also set a limiter if there is a...

26
Controlling the peripheral devices 
connected to a remote camera
The peripheral devices connected to a remote camera can be controlled .Control the devices with FUNCTION menu [23] .
1 . Press the MENU button .
2 . Open FUNCTION menu [23] .
Controlling an AW‑PS300A AC adapter
When an AW‑PH360 is being controlled with the unit, you can control an 
AW‑PS300A AC adapter via the AW‑PH360 .
zzFor details on how to connect the 

AW‑PH360 and AW‑PS300A, refer 
to the Operating Instructions for each device
 ....

27
Configuring the unit operation settings
Enabling or disabling operation with the ENABLE buttons
The unit has five ENABLE buttons .Each of the ENABLE buttons can be used to independently enable or disable the corresponding operation shown below .
USER ENABLE buttonzzOperation of USER buttons
MEM
 
ENABLE button
zz Operation of memory (preset memory and tracing memory)
Color adjustment ENABLE button
zzOperation of color adjustment section
PAN/TILT ENABLE buttonzzOperation of PAN/TILT lever...

28
Configuring the unit operation settings (continued)
Enabling or disabling operation of the 
ENABLE buttons by menu operation
Operation of the ENABLE buttons can be enabled or disabled by menu 
operation .
Disabling operation prevents erroneous operation because the enable/
disable states become unable to be changed even by pressing the 
ENABLE buttons

 .
1 . Press the MENU button .
2 . Open RP SETUP menu [25]  .
3 . Turn the F1 dial to display the “4  .  ENABLE   BUTTON” 
item  .
4 . E N A B L E   B...

29
Switching the focus operation and iris 
operation
The operations of the FOCUS dial and IRIS dial can be switched .
1 . Press the MENU button .
2 . Open RP SETUP menu [25]  .
3 . Turn the F1 dial to display the “1  .  FOCUS/IRIS” item  .
1 . F O C U S / I R I S
              S T A N D A R D
4 . Turn the F2 dial to select “EXCHANGE” or 
“STANDARD”, and then press the F2 dial to confirm the 
selection
 .
EXCHANGE : Switches the operations of the FOCUS dial and IRIS 
dial
 .
zzWhen this is set to...

30
Assigning functions to the USER buttons
Functions can be assigned to the eight USER buttons (USER 1 to 
USER   8)  .
This enables you to operate a desired function by simply pressing a 
USER button (USER

  1 or USER   8)  .
USER buttons (USER

  1 to USER   8)
1 . Press the MENU button .
2 . Open USER BUTTON menu [35] .
3 . Turn the F1 dial to display the USER button (USER 1 to 
USER 8) you want to set .
4 . Turn the F2 dial to select a function, and then press the 
F2 dial to confirm the selection...