Panasonic Remote Camera Controller Aw Rp120 Operating Instructions

11
Operating the OSD menu of a remote camera
To set the advanced settings of a remote camera, operate the menu superimposed on the image output of the remote camera (this menu is referred to 
as the OSD menu in this manual) .  The OSD menu of a connected remote camera can be operated from the unit  .
CAMERA

 OSD button
F1 dial
F2 dial EXIT button
1 . Hold down the CAMERA OSD button to turn on its indicator .The OSD menu of the selected remote camera appears and becomes able to be operated from the unit...

12
Operating preset memory (PMEM)
The preset memory of a remote camera can be operated from the unit .The following settings that you have adjusted in advance can be stored 
in preset memory .
zzPan/tilt positions
zz Zoom positions
zz Focus positions zz
Lens iris settings (manual iris only)
zz White balance settings
zz Gain
zz If the MEM

  ENABLE button indicator is off, preset memory 
operation is not possible
 .  Press the button to turn on its indicator 
and then perform operation
 .
zzPreset numbers...

13
Registering preset memory (STORE)
1 . Press one of the camera selection buttons 
[CAMERA
 
SELECT/GROUP
 
 SELECT] to select the 
remote camera to be operated
 .
2 . Output the images to be shot to the monitor .
3 . Press the PMEM button to turn on its indicator .
4 . Press the MEM STORE button to turn on its indicator .
5 . Operate the PAN/TILT lever and ZOOM button to 
determine the camera angle to register
 .If necessary, adjust the focus and iris as well .
6 . Hold down a number button to specify...

14
Setting the operation items for when preset 
memory is recalled (PRESET SCOPE)
You can select whether to recall all or only some of the settings 
registered to preset memory .
zzThis function is enabled when 

AW‑HE50, AW‑HE60, or 
AW‑HE120 is selected
 .
Note
1 . Press one of the camera selection buttons 
[CAMERA
 
SELECT/GROUP
 
 SELECT] to select the 
remote camera to be operated
 .
2 . Press the PMEM button to turn on its indicator .
3 . Press the MEM SETTING button .The setting of the selected...

15
Registering PRESET SPEED on the unit
To register the PRESET SPEED value to a preset number of the unit, 
perform the following steps after the previous procedure  .
5 . Press the MEM STORE button to turn on its indicator .
6 . Hold down a number button to specify the preset 
number to register
 .The current remote camera settings are registered to preset 
memory, and PRESET SPEED is registered to the unit .
 
z T

o continue registering a different PRESET
 
 SPEED value to a 
preset memory belonging...

16
Operating preset memory groups (PMEM GROUP)
The unit allows you register up to four “preset memory groups” created 
by selecting one preset memory for each of multiple remote cameras .
Pressing any of the PM GRP

 1 to PM GRP 4 buttons simultaneously 
recalls all preset memory registered to the corresponding preset 
memory group
 .
The following setting procedures use the example of setting 
PMEM

  GROUP1 but the setting procedures are the same for 
PMEM
  GROUP2 to PMEM GROUP4  .
Open the following...

17
Registering the preset memory to recall when in ALL 
mode
1 . Press the MENU button to turn on its indicator .
2 . Open PM GRP1 menu [31] .
1 . P M   G R P 1   M O D E
                        A L L
3 . Turn the F1 dial to display the “12 .  PM   GRP1  ALL” item  .
1 2 . P M   G R P 1   A L L
                  P R E 0 0 1
4 . Turn the F2 dial to select a preset number, and then 
press the F2 dial to confirm the selection
 .
Recalling preset memory groups
Pressing a button to recall a preset memory...

18
Operating tracing memory (TMEM)
The unit incorporates tracing memory (TMEM) for recording a series of 
operations that were performed for a connected remote camera .
This feature allows you to duplicate the recorded operations of a remote 
camera

 .

Recording target Camera numbers CAM1 to CAM10
Functions that 
can be recorded Pan, tilt, zoom, focus, iris, and white balance 
mode
Recording time Up to 5 minutes per camera
Number of 
recording 
memory Up to 10 per camera
Record buttons Number buttons...

19
Operating tracing memory (TMEM) (continued)
6 . Hold down one of the number buttons [1] to [10] that 
has its indicator turned off to specify the tracing 
memory number
 .The current camera position and settings are registered to the preset 
memory of the remote camera, and become the start position and 
settings at the time of recalling .
The indicators of the number button that was held down and ST

ART 
button [11] blink
 .  (Recording standby state)
 zIf 

an operation that is target for recording...

20
Operating tracing memory (TMEM) (continued)
Deleting tracing memory (DELETE)
1 . Press one of the camera selection buttons 
[CAMERA
 
SELECT/GROUP
 
 SELECT] to select the 
remote camera to be operated
 .
2 . Press the TMEM button to turn on its indicator .The tracing memory status appears .The indicators of number buttons with registered tracing memory 
turn on
 .
C A M 0 1 : T M E M
3 m 5 0 s   R e m a i n e d \f
Selected camera number
Remaining possible recording time (max
 .  5 m 00 s)
zzA button...