Panasonic Projector PT-D7700U PT-DW7000U User Manual

							81
SECURITY
  PASSWORD OFF
  PASSWORD CHANGE
  TEXT DISPLAY OFF
  TEXT CHANGE 
  
SECURITY
  PASSWORD OFF
  PASSWORD CHANGE
  TEXT DISPLAY OFF
  TEXT CHANGE 
  
  
  
SECURITY
  PASSWORD OFF
  PASSWORD CHANGE
  TEXT DISPLAY OFF
  TEXT CHANGE 
  
TEXT
PASSWORD
   NEW
   CONFIRM
           :INPUT          ENTER:SET
Select “TEXT DISPLAY” with the 
buttons.
Select “ON” or “OFF” with the 
buttons.
ON: The text display is enabled.
OFF: The text display is disabled.
Note
• Only asterisks  will appear on the screen to
represent the actual characters of the password
when the password is entered.
Changing the password
The password can be changed.
Setting the text
The set text can be permanently displayed below the pictures being projected.
Changing the text
The characters displayed in the text can be changed when “ON” has been selected as the “TEXT DISPLAY”
setting.
Select “PASSWORD CHANGE” with the
buttons.
Select “TEXT CHANGE” with the 
buttons.
Press the “ENTER” button.
The PASSWORD screen will be displayed.
Set the password with the  ,  , 
and buttons.
Up to eight buttons can be set as the password.
Press the “ENTER” button.
For the purposes of confirmation, enter
the password again.
Press the “ENTER” button.
Press the “ENTER” button.
The TEXT screen will be displayed.
Select the text position with the 
buttons and the characters of the text
with the  buttons.
Press the “ENTER” button.
The text is now changed. 
						

							82
How to use CP OPTION
MAIN MENU
         PICTURE
         POSITION
         ADVANCED MENU
         LANGUAGE
         OPTION
         TEST PATTERN
         SIGNAL LIST
         SECURITY
         CP OPTION
     :MENU SELECT
ENTER:SUB MENU
CP OPTION
  OSD ON
  SYSTEM SELECTOR
  
   
  
  
  
  
     :MENU SELECT    
     :CHANGE
The on-screen indication can be turned “ON” or “OFF” and the system selector setting can be changed using the
rear panel operating section of the main unit.
Setting the on-screen indication function
Procedure of setting
Hold down the “MENU” button for 3 or
so seconds.
If the on-screen function is “OFF”, the on-screen
indication will now appear, and the “CP OPTION”
item will be added to the main menu.
Select “CP OPTION” with the 
buttons.
Press the “ENTER” button.
The CP OPTION screen will be displayed.
Select “OSD” with the  buttons.
Select “ON” or “OFF” with the 
buttons.
ON: The on-screen indication function is set to
“ON”.
OFF: The on-screen indication function is set to
“OFF”. 
						

							83
MAIN MENU
         PICTURE
         POSITION
         ADVANCED MENU
         LANGUAGE
         OPTION
         TEST PATTERN
         SIGNAL LIST
         SECURITY
         CP OPTION
     :MENU SELECT
ENTER:SUB MENU
CP OPTION
  OSD ON
  SYSTEM SELECTOR
  
   
  
  
  
  
     :MENU SELECT    
     :CHANGE
SYSTEM SELECTOR
  VIDEO AUTO1
  S-VIDEO AUTO1
  
   
  
  
  
  
     :MENU SELECT    
     :CHANGE   ENTER:EXECUTE
Setting the system format
Procedure of setting
Hold down the “MENU” button for 3 or
so seconds.
If the on-screen function is “OFF”, the on-screen
indication will now appear, and the “CP OPTION”
item will be added to the main menu.
Select “SYSTEM SELECTOR” with the
buttons.
Press the “ENTER” button.
The SYSTEM SELECTOR screen will be
displayed.
Select one of the following inputs for
setting the system format with the
buttons.
“RGB1”, “RGB2”, “VIDEO”, “S-VIDEO”, “AUX”
Note• Only the inputs enabling the system
format to be selected are actually
displayed.
Note• For details on which system format can be
selected, refer to “How to change the
system format” (on page 65).
Select the system format with the 
buttons.
Press the “ENTER” button. 
						

							84
The input module (ET-MD77NT, ET-MD77DV, ET-MD77SD1 or ET-MD77SD3) available as an optional accessory
comes with a network function to enable the projector to be controlled from the Web browser of the personal
computer.
In addition, the network function also fulfills automatic E-mail transmission function.  It can send mail to a
predefined E-mail address when the system malfunctions or when the lamp used hours reaches the set value.
Example of connection
A LAN cable is required to use the network function.
Hub
LAN cable (straight)
PC
• A Web browser is required to use this function.  Make sure that a Web browser is available in the system.
• Use Microsoft Windows 98SE/Me/NT4.0/2000/XP for the OS of your personal computer.
• The Web browser should be Internet Explorer 6.0 or later or Netscape Communicator 7.0 or later.
• To use the E-mail function, communication with E-mail server must be established.  Make sure that E-mail
feature is available in your system.
• Use a straight insulated LAN cable which supports category 5 or above.
• The length of LAN cable must be 100 m or shorter.
Name and function of network function parts
LAN cable (straight)
Projector
• If the LAN terminal is touched by electrostatically charged hands (or body), failure may be caused by the
discharge of static electricity.
Be careful not to touch metallic part of LAN terminal or LAN cable.
How to use network function (optional)
Attention
Network Module
ET-MD77NT
LAN
LAN terminal (10 Base-T/100 Base-TX)
Connect LAN cable here.
LAN10/100 lamp (yellow)
This lights when a 100Base-TX connection is
established.LAN LINK/ACT lamp (green)
This lights when a LAN cable is
connected and flashes when signals are
being received or sent. 
						

							85
Press the “ENTER” button.
The OPTION screen will be displayed.
Select “NETWORK SETTING” with the
buttons.
Initial setting of network function
Procedure of setting
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select “OPTION” with the 
buttons.
MAIN MENU
         PICTURE
         POSITION
         ADVANCED MENU
         LANGUAGE
         OPTION
         TEST PATTERN
         SIGNAL LIST
         SECURITY
     :MENU SELECT
ENTER:SUB MENU
OPTION
  PROJECTOR ID 2
  SETTING FRONT-F
  LAMP SELECT DUAL
  LAMP POWER HIGH
  RS232C SETTING
  OSD POSITION 2
  SYSTEM INFORMATION
  COLOR MATCHING 3COLORS
  VIDEO SETTING
  NETWORK SETTING
     :MENU SELECT
ENTER:SUB MENU
NETWORK SETTING
  HOST NAME PROJECTOR
  DHCP OFF
  IP ADDRESS 192.168.    0.    8
  PORT       80
  NET MASK 255.255.255.    0
  GATEWAY 192.168.    0.    1
  MAC ADDRESS 00.00.00.00.00.00
  STORE
     :MENU SELECT    
ENTER:ADJUSTPress the “ENTER” button.
The NETWORK SETTING screen will be
displayed.
Select items with the  buttons and
press the “ENTER” button to change
the setting.
Select the “STORE” with the 
buttons and press the “ENTER” button
twice.
(Continued on next page)
Note• The network settings are stored in the input module installed inside the projector. Perform
these settings again when the installed input module has been replaced. 
						

							86
How to use network function (optional)
Items FunctionDescription
HOSTNAME
DHCP
IP ADDR
PORT No.
NET MASK
GATEWAY
MAC ADDRMake alteration if necessary when to use the 
DHCP server.
Set the DHCP item to ON when to acquire an IP 
address automatically using the DHCP server. 
Set to OFF if DHCP server is not used.
Enter the IP address if DHCP server is not used.
Number 80 is normally used. 
Change the data if necessary.
Enter the net mask if DHCP server is not used.
Enter the gateway address if DHCP server is not used.
Displays the MAC address (Media Access Control 
Address), which is proper to the network device.  
This function may be needed when to use the DHCP server.
Display of host name and setting
DHCP client function
Display of IP address and setting
Display and setting of the port 
number for connection with the 
Web browser.
Display of net mask and setting
Display of gateway address and 
setting
Display of MAC address
• Before using the DHCP server, make sure the DHCP server is already functioning.
• For details of IP address, net mask, and gateway, ask the network administrator.
Initial setting of network function (continuing) 
						

							87
• Avoid activating two or more Web browser simultaneously to work out setting or control actions.
• Change the password first of all.
Note
Accessing from the Web browser
Activate the Web browser in the personal computer.
Enter the IP address set by the projector into the URL input field of the Web
browser.
Enter “user1” in the user name field and enter “panasonic” (lower case) in the
password field.
Press OK and the top page will appear.
Password change page
Click [Change password].
Old password input field
New password input field
New password input field
(re-enter for confirmation)
Button for executing
password changeButton for erasing all
entered characters   
						

							88
How to use network function (optional)
Basic control page
This page is the first page displayed when the projector is accessed through a web browser.
To move from another page, click [Projector control], then [Basic control]. 
Control button
Click this item, and a
projector control page
appears.
Update button
Click this item, and the
update page of the
projector’s firmware
appears.
E-mail set up button
Click this item, and an
E-mail setting page
appears.
Monitor information
button
Click this item, and the
status of the projector
is displayed.
OSD
(On-screen Display)
display/non-display
Use these to select
the input signals.
System type switching
Network set up button
Click this item, and a network
set up page for IP address and
other items appear.Change password button
Power On/Off control 
Shutter control   
						

							89
(Continued on next page)
Detail control page
Click [Projector control], then [Detail control] to display the Detail control page.
On-screen status is
displayed, even if the
on-screen of projector
is set to off.
Lens adjustment
Menu display
Test pattern display
This button updates the
on-screen description
on the right of the
control page with the
latest information. Pressing these buttons controls the projector and
updates the on-screen description on the right of the
control page when control is finished.
Monitor information page
Click [Projector control], then [Status information] to display the Status information page.
This page displays the projector statuses established for the items shown below.
Displays the input switching
status.
Displays temperature of
projector’s intake air.
Displays temperature inside
the projector.
Displays temperature of
projector exhaust.
Displays the lamp lit hours.
Displays used hours of the
projector.
Displays self-diagnosis
information.Displays the type of
projector.Displays the firmware version of
the projector main unit.   
						

							90
How to use network function (optional)
When  is displayed on the status information screen, click it to display the error details.
Error information page
OK: Normal operation
FAILED: Occurrence of trouble
When [FAILED] has appeared for an item
Parameter
MAIN CPU BUS
FAN
OPTICS MODULE
TEMPERATURE
INPUT AIR TEMPERATURE
OUTPUT AIR TEMPERATURE
LAMP REMAIN TIME
LAMP STATUS
APERTURE (CONTRAST-SHUTTER)
SHUTTER (MUTE-SHUTTER)
OPTICS MODULE TEMP.SENSOR
INPUT AIR TEMP.SENSOR
OUTPUT AIR TEMP.SENSOR
BATTERY
Description
Trouble has occurred in the microcomputer circuitry. Consult your dealer.
Trouble has occurred in the fan or its drive circuit. Consult your dealer.
The temperature inside the projector is high. It may be that the projector is
being used where the ambient temperature is high such as near a heating
appliance.
The input air temperature is too high. It may be that the projector is being
used where the ambient temperature is high such as near a heating
appliance.
The exhaust air temperature is too high. It may be that the projector’s
ventilation holes are blocked.
The lamp runtime has exceeded the prescribed cumulative time, and it is
now time to replace the lamp.
The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
Trouble has occurred in the contrast shutter circuitry. Consult your dealer.
Trouble has occurred in the shutter circuitry. Consult your dealer.
Trouble has occurred in the temperature detection sensor inside the
projector. Consult your dealer.
Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer.
Trouble has occurred in the sensor used to detect the exhaust air
temperature. Consult your dealer.
The backup battery has been run out. Consult your dealer.
• Depending on the nature of the error, the projector may be placed in the standby mode for its own protection.
Note