Panasonic Projector PT-D7700U PT-DW7000U User Manual
Have a look at the manual Panasonic Projector PT-D7700U PT-DW7000U User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
51
PICTURE
PICTURE MODE DYNAMIC
COLOR 50
TINT 30
COLOR TEMP. DEFAULT
GAMMA 2.2
CONTRAST 32
BRIGHT 32
SHARPNESS 6
NOISE REDUCTION 2
DYNAMIC IRIS 1
:MENU SELECT
:CHANGE
Press the “MENU” button.
The MAIN MENU screen will be displayed
Select “PICTURE” with the
buttons.
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
Press the “ENTER” button.
The PICTURE screen will be displayed.
Select “COLOR TEMP.” with the
buttons.
Select the desired setting from below
with the buttons.
“LOW”, “MIDDLE”, “HIGH”, “DEFAULT”, “USER1”
and “USER2”
WHITE BALANCE
WHITE BALANCE HIGH
WHITE BALANCE LOW
Select “USER1” or “USER2” in Step .
Press the “ENTER” button.
Select “WHITE BALANCE HIGH” or
“WHITE BALANCE LOW” with the
buttons.
• All colours will not be displayed properly unless adequate adjustment is made.
If the adjustment is not successful, press “STD” (standard) button when the individual adjustment
screen is displayed to restore the factory default setting only for the displayed item.
• The color temperature cannot be adjusted for the internal test pattern (refer to page 79). Be sure to
project the input signal when adjusting the color temperature.
• When any setting other than “OFF” has been selected for color matching, the COLOR TEMP. setting is
fixed at “USER1”
• “DEFAULT” cannot be selected when the picture mode has been set to “USER”Note
Press “ENTER” button.
The WHITE BALANCE HIGH (LOW) screen will be
displayed.
Select “R”, “G” or “B” with the
buttons.
Adjust the level with the buttons.
R (Red)Deepens red.
Weakens red.
Deepens green.
Weakens green.
Deepens blue.
Weakens blue.
G (Green)
B (Blue)
Maximum value 255
Minimum value 0
WHITE BALANCE HIGH
R 255
G 255
B 255
Press button
Press button
ItemAdjustment Remarks Operation
Adjusting the color temperature
Adjustment procedure (to be performed while projecting the signals to be adjusted)
Press button
Press button
Press button
Press button
52
Adjusting the picture
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select “PICTURE” with the
buttons.
Press the “ENTER” button.
The PICTURE screen will be displayed.
Select desired one of the items in the
following table with the buttons.
Switch the setting with the
buttons.
Refer to the following table for the items and the
details.
Sharpness / Gamma / Noise reduction
Procedure of adjustment
PICTURE
PICTURE MODE DYNAMIC
COLOR 50
TINT 30
COLOR TEMP. DEFAULT
GAMMA 2.2
CONTRAST 32
BRIGHT 32
SHARPNESS 6
NOISE REDUCTION 2
DYNAMIC IRIS 1
:MENU SELECT
:ADJUST
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
Adjustment itemsAdjustment
Sharpness
0 to 7 for the RGB system and the HD system
(factory setting is 2)
0 to 15 for the SD system (factory setting is 6)
5 settings: DEFAULT, USER1, USER2, 2.2 and
2.5
(factory setting: DEFAULT)
Gamma selection
Sharpens the outline of the image.
Switches the gamma modes
Operation
Four types: OFF (no correction), 1 (low),
2 (middle), 3 (high) (factory default: 2)Noise reductionSwitches the noise reduction effect
mode.
Note
• Noise reduction cannot be adjusted with analog RGB input, DVI input or network input.
• Separate software is required to select “USER1” and “USER2” as the gamma setting. Consult your
dealer.
To display pictures complying with the sRGB standard
sRGB is the international reproduction standard (IEC61966-2-1) established by IEC (International
Electrotechnical Commission).
To reproduce colours more faithfully in compliance with the sRGB standard, perform the following setting
procedure.
1. Set color matching adjustment to “OFF”.
2. Press the buttons on the “PICTURE” menu and select the “PICTURE MODE”.
Set to “NATURAL” with the buttons.
3. Select the “COLOR” with the buttons.
Press the STD (standard) button on the remote control to restore the factory default.
Follow the same procedure to restore the factory default for “TINT”, “COLOR
TEMP.” and “GAMMA”.
• sRGB is only enable when RGB signals are being input.Note
53
Adjusting the position
Desired position can be achieved by following the procedure below.
Shift adjustment
This function allows the user to adjust the picture position vertically or horizontally if the position of the image
projected on the screen is displaced when the projector is properly positioned against the screen.
Procedure of adjustment
POSITION
SHIFT
SIZE DEFAULT
CLOCK PHASE 0
KEYSTONE
:MENU SELECT
ENTER:SUB MENU
Press the “MENU” button.
The MAIN MENU screen will be displayed
Select the “POSITION” with the
buttons.
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
:MENU SELECT
ENTER:SUB MENU
Press the “ENTER” button.
The POSITION screen will be displayed.
Select “SHIFT” with the buttons.
SHIFT
V: 0
H: 0
:ADJUSTPress the “ENTER” button.
The SHIFT screen will be displayed.
Adjust the position with the
buttons.
Press the “MENU” button three times.
The on-screen indications disappear and the
normal screen appears again.
Pressing button will
move the image to the
right.Pressing button will
move the image to
the left.
Pressing button will
move the image upward.Pressing button will
move the image
downward.
54
Adjusting the position
POSITION
SHIFT
SIZE DEFAULT
CLOCK PHASE 0
KEYSTONE
:MENU SELECT
:CHANGE ENTER:SUB MENU
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select the “POSITION” with the
buttons.
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
:MENU SELECT
ENTER:SUB MENU
ZOOM
INTERLOCKED: OFF
V: 100 %
H: 100 %
HV: 100 %
:MENU SELECT
:CHANGEPress the “ENTER” button.
The SIZE adjustment screen will be displayed.
Select the desired item with the
buttons.
Adjust with the buttons.
Size adjustment
Procedure of adjustment
Press the “ENTER” button.
The POSITION screen will be displayed.
Select “SIZE” with the buttons.
Using the buttons, select the size
mode.
For details on the size mode, refer to the next
page.
• If “THROUGH” is selected in the size mode, the individual adjustment screen is not displayed.Note
55
Some size modes are not available for certain types of input signals.
• For RGB1 and RGB2 input signals: VID AUTO, S1 AUTO or VID AUTO (PRIORITY) cannot be selected.
• For VIDEO input signals: DEFAULT, S1 AUTO or VID AUTO (PRIORITY) cannot be selected.
• For an NTSC signal with VIDEO or S-VIDEO input: DEFAULT cannot be selected.Note
Size modes
•DEFAULT:Pictures are displayed without changing the aspect ratio of the input signals.
• THROUGH:Pictures are displayed without changing the resolution of the input signals.
•ZOOM:Pictures can be displayed in various magnifications. The user can magnify the pictures with the
magnification ranging from 50% to 999%, and the fiducial point is set on the top left of the screen.
•16:9 (D7700U only): Pictures are displayed in the aspect ratio of 16:9.
•4:3 (DW7000U only): Pictures are displayed in the aspect ratio of 4:3.
• S4:3 (D7700U only): Pictures are scaled down to 75% of the original size without changing the aspect ratio of the
input signals. This mode is used when projecting the 4:3 pictures on the 16:9 screen.
• H FIT (DW7000U only): Pictures are displayed using all the panel pixels in the horizontal direction.
Signals with an aspect ratio where the pictures are taller than with a ratio of 16:9 will be
displayed with their bottom areas cut off.
• HV FIT: Pictures are displayed on the whole panel pixels.
If the aspect ratio of the input signals is different from that of the panel, the pictures are displayed by
converting it into the panels aspect ratio (4:3 for PT-D7700U and 16:9 for PT-DW7000U).
• VID AUTO:The projector identifies the video ID (VID) embedded in the picture signals and displays the picture by
automatically switching the screen sizes between 4:3 and 16:9.
This function is effective for the video and S-video input.
• S1 AUTO:The projector identifies the S1 signal and displays the picture by automatically switching the screen
sizes between 4:3 and 16:9.
This function is effective for the S-video input.
• VID AUTO (PRIORITY): The projector identifies the abovementioned VID or S1 signals and displays the picture
by automatically choosing the screen sizes of 4:3 or 16:9 according to the VID if it is
detected or S1 signals if a VID is not detected.
This function is effective for the S-video input.
POSITION
SHIFT
SIZE DEFAULT
CLOCK PHASE 0
KEYSTONE
Press the “MENU” button.
The MAIN MENU screen will be displayed
Select the “POSITION” with the
buttons.
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
Press the “ENTER” button.
The POSITION screen will be displayed
Select “CLOCK PHASE” with the
buttons.
Adjust the clock phase with the
buttons.
The value changes from 0 to 31.
Clock phase adjustment
Clock phase adjustment achieves the best image when the screen flickers or halo is observed around the contour.
Procedure of adjustment
• No optimal value may be obtained if the output of the PC to which the signal input is applied is unstable.
• No optimal value may be obtained if the total number of dots is not correct.
• The clock phase can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN.Note
56
Adjusting the position
POSITION
SHIFT
SIZE DEFAULT
CLOCK PHASE 0
KEYSTONE
:MENU SELECT
ENTER:SUB MENU
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
:MENU SELECT
ENTER:SUB MENU
KEYSTONE
KEYSTONE 63
LINEARITY 63
:ADJUST
Keystone distortion correction
Keystone distortion can be corrected only along either horizontal bound of the picture.
Procedure of adjustment
Note
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select the “POSITION” with the
buttons.
Press the “ENTER” button.
The POSITION screen will be displayed.
Select “KEYSTONE” with the
buttons.
Press the “ENTER” button.
The KEYSTONE screen will be displayed.
Adjust the “KEYSTONE” horizontally
with the buttons.
The value changes from 0 to 127.
Adjust the vertical “LINEARITY” with
the buttons.
The value changes from 0 to 127.
• Adjust the “LINEARITY” after adjusting the “KEYSTONE”.
The variable range of the “LINEARITY” changes in response to the adjusted value of the
“KEYSTONE”.
• Pressing STD (standard) button of the remote control will restore the factory default (“KEYSTONE”: 63,
“LINEARITY”: 63).
• The adjusted value is reflected in other input signals.
• Keystone distortion can be corrected to ±40°of the angle of tilt for the projector against the screen.
(The range for the angle of elevation is within ±19°when using a lens with a fixed focal point, and it is
within ±34°when using an LE1 lens.)
57
How to use ADVANCED MENU
• In DIGITAL CINEMA REALITY mode, the image quality will be deteriorated if 30p FIXED or 25p FIXED
is selected when the signal is not a 2:2 pulldown signal.Note
ADVANCED MENU
DIGITAL CINEMA REALITYAUTO
FORMAT SMPTE
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING OFF
SYNC.TERM 75
RASTER POSITION
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
DIGITAL CINEMA REALITY
Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i signal input is applied.
Procedure of adjustment
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select “ADVANCED MENU” with the
buttons.
Press “ENTER” button.
The ADVANCED MENU screen will be displayed.
Select “DIGITAL CINEMA REALITY”
with the buttons.
OFF: Unforced cinema processing
AUTO: Performs automatic detection and cinema
processing. (factory default)
30p FIXED: Forced cinema processing (2:2
pulldown) is performed when a 480i
signal is input.
25p FIXED: Forced cinema processing (2:2
pulldown) is performed when a 576i
signal is input.
58
How to use ADVANCED MENU
ADVANCED MENU
DIGITAL CINEMA REALITYAUTO
FORMAT SMPTE
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING OFF
SYNC.TERM 75
RASTER POSITION
:MENU SELECT
ENTER:SUB MENU
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select the “ADVANCED MENU” with
the buttons.
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
:MENU SELECT
ENTER:SUB MENU
Press the “ENTER” button.
The ADVANCED MENU screen will be displayed.
Select “BLANKING” with the
buttons.
BLANKING
UPPER 0
LOWER 0
LEFT 0
RIGHT 0
:MENU SELECT
:ADJUSTPress the “ENTER” button.
The BLANKING adjustment screen will be
displayed.
Select the desired item for adjustment
with the buttons.
Adjust blanking with the buttons.
The value changes from 0 to 511.
Press button to move
the blanking zone upward;
button to downward.Press button to move
the blanking zone upward;
button to downward.
Press button to move
the blanking zone to the
right; button to the left.Press button to move
the blanking zone to the
right; button to the left.
Blanking adjustment
Blanking adjustment fine-tunes the images projected by the video deck or other devices when the noise appears on
the edges of the screen or if a part of the image lies slightly offscreen.
Procedure of adjustment
59
ADVANCED MENU
DIGITAL CINEMA REALITYAUTO
FORMAT SMPTE
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING OFF
SYNC.TERM 75
RASTER POSITION
:MENU SELECT
ENTER:SUB MENU
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
:MENU SELECT
ENTER:SUB MENU
INPUT RESOLUTION
TOTAL DOTS 1056
DISPLAY DOTS 832
TOTAL LINES 666
DISPLAY LINES 624
:MENU SELECT
:ADJUSTPress the “ENTER” button.
The INPUT RESOLUTION screen will be
displayed.
Select one of the following items with
the buttons and adjust it with the
buttons.
“TOTAL DOTS”, “DISPLAY DOTS”, “TOTAL
LINES” and “DISPLAY LINES”
Each item automatically displays a value in response
to the type of the input signal. If vertical stripes
appear on the screen or the image is partly missing,
increase or decrease the displayed value while
observing the screen to achieve the optimal value.
Adjusting the input resolution
Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the
contour.
Procedure of adjustment
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select the “ADVANCED MENU” with
the buttons.
Press the “ENTER” button.
The ADVANCED MENU screen will be displayed.
Select “INPUT RESOLUTION” with the
buttons.
• The abovementioned vertical stripes will not appear on the screen when all signals are input.
• The picture may be distorted during the adjusting operation, but this is not a fault.
• The input resolution can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN.Note
60
How to use ADVANCED MENU
ADVANCED MENU
DIGITAL CINEMA REALITYAUTO
FORMAT SMPTE
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING OFF
SYNC.TERM 75
RASTER POSITION
:MENU SELECT
ENTER:SUB MENU
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
:MENU SELECT
ENTER:SUB MENU
CLAMP POSITION
POSITION 1
:MENU SELECT
:ADJUST
The optimal value for the clamp position adjustment
• If dark areas are crushed: The optimal value is the point where the dark area is best improved.
• If the dark areas are displayed in green: The optimal value is the point where the green area becomes dark
and clear.
Adjusting the clamp position
Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or
displayed in green.
Procedure of adjustment
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select “ADVANCED MENU” with the
buttons.
Press the “ENTER” button.
The ADVANCED MENU screen will be displayed.
Select “CLAMP POSITION” with the
buttons.
Press the “ENTER” button.
The CLAMP POSITION screen will be displayed.
Adjust with the buttons.
The value changes from 1 to 255.
Note
• The clamp position can be adjusted only when the RGB signal input is applied with RGB1 and RGB2
IN.