Panasonic Projector PT-D7700U PT-DW7000U User Manual
Have a look at the manual Panasonic Projector PT-D7700U PT-DW7000U User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
61
ADVANCED MENU
DIGITAL CINEMA REALITYAUTO
FORMAT SMPTE
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING ON
SYNC.TERM 75
RASTER POSITION
:MENU SELECT
:CHANGE ENTER:SUB MENU
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
EDGE BLENDING
UPPER START 0
OFF WIDTH 128
LOWER START 0
OFF WIDTH 128
LEFT START 0
OFF WIDTH 128
RIGHT START 0
OFF WIDTH 128
MARKER OFF
BRIGHT ADJUST
:MENU SELECT
:ADJUST
ENTER:CHANGE
Press the “ENTER” button.
The EDGE BLENDING screen will be displayed.
Specify the area to be adjusted with the
buttons.
To joint the top: set “UPPER” to “ON”.
To joint the bottom: set “LOWER” to “ON”.
To joint the left: set “LEFT” to “ON”.
To joint the right: set “RIGHT” to “ON”.
Press the “ENTER” button to toggle
“ON” and “OFF”.
Adjust the compensation width and
start position with the buttons.
Select “MARKER” with the
buttons.
Select “ON” with the ENTER buttons.
The optimal point is where
these lines overlap.
Red line Red lineGreen line Green line
Adjustment marker
When the “MARKER” is set to “ON”, the image position adjustment
marker is displayed.
The optimal point is the position where the red line of one frame
overlaps the green line of the other frame.
Notice:
The correction widths of the jointed frames must be the same
value all the time.
The optimal joint cannot be achieved if the jointed frames have
different correction widths.
Edge blending adjustment
This projector has the function to hide the seams for multi-screens.
Procedure of adjustment
Note
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select the “ADVANCED MENU” with
the buttons.
Press the “ENTER” button.
The ADVANCED MENU screen will be displayed.
Select “EDGE BLENDING” with the
buttons.
Select “OFF”, “ON” or “USER” with the
buttons.
OFF: When the multi-screens are not going to be
used.
ON: When the tilting inside the unit is to be used
for the tilting of the edge blending area.
USER: When a specific tilting is to be used for the
tilting of the edge blending area.
(Separate software is required to establish
these settings. Consult your dealer.)
(Continued on next page)
62 How to use ADVANCED MENU BRIGHT ADJUST BRIGHT INSIDE 6 BRIGHT OUTSIDE 6 UPPER 0 LOWER 0 LEFT 0 RIGHT 0 Projection range Edge blending width (right) BRIGHT adjustment (right) Marker BRIGHT INSIDE BRIGHT OUTSIDE Select the “BRIGHT ADJUST” with the buttons. Press the ENTER button. The BRIGHT ADJUST screen will be displayed. Select the “BRIGHT INSIDE” with the buttons. Adjust the compensation value (0-255) with the buttons. Select the part of Upper, Lower, Right, Left with buttons. With the buttons, adjust the width (0 to 255) where no BRIGHT INSIDE compensation is to be provided. Select the BRIGHT OUTSIDE with the buttons. Adjust the compensation value (0-255) with the buttons. • The BRIGHT adjustment is a function for making the brightening of the BRIGHT level in those areas where the pictures overlap less conspicuous when multi-screens have been configured using edge blending. The optimal point is where, after the BRIGHT INSIDE has been adjusted, the compensation amount is the same for the BRIGHT levels in the areas where the pictures overlap and where the pictures do not overlap. If, after the BRIGHT INSIDE adjustment, only the vicinity of the borders of the areas where the pictures overlap and where the pictures do not overlap becomes bright, proceed to adjust the top, bottom, left and right widths. Alternatively, if only the vicinity of the borders has darkened as a result of the width adjustments, proceed with the BRIGHT OUTSIDE adjustment. • When a rear screen or screen with a high gain is used, the joints may appear to be discontinuous depending on the viewing position.Note Edge blending adjustment (continuing)
63
ADVANCED MENU
DIGITAL CINEMA REALITYAUTO
FORMAT SMPTE
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING OFF
SYNC.TERM 75
RASTER POSITION
RASTER POSITION
V: 0
H: 0
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
Raster position
When the whole area where the input picture can be displayed is not used, the picture can be moved to any
position inside the display area.
Procedure of adjustment
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select “ADVANCED MENU” with the
buttons.
Press “ENTER” button.
The ADVANCED MENU screen will be displayed.
Select “RASTER POSITION” with the
buttons.
Press the “ENTER” button.
The RASTER POSITION screen will be displayed.
Adjust the position with the
,,
and buttons.
Press the “MENU” button three times.
The on-screen indications disappear and the
normal screen appears again.
Pressing button will
move the image to the
right.Pressing button will
move the image to
the left.
Pressing button will
move the image upward.Pressing button will
move the image
downward.
PT-D7700U
Pressing button will
move the image to the
right.Pressing button will
move the image to the
left.
PT-DW7000U
64
Changing the display language
• The on-screen display of the projector is set
to the English language on shipping.Note
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select the “LANGUAGE” with the
buttons.
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
:SELECT ENTER:SET
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
Press the “ENTER” button.
The LANGUAGE screen will be displayed.
Select the desired language with the
buttons.
Press the “ENTER” button to establish
your selection.
When this is selected, the language display will
turn a light green.
Menus, setting items, adjustment screens, and
control button names will be displayed in the
language the user chooses.
The available languages are: English, German
(DEUTSCH), French (FRANÇAIS), Spanish
(ESPAÑOL), Italian (ITALIANO), Japanese ( ),
Chinese ( ), Russian ( ) and
Korean ( ).
65
How to change the system format
Pressing the SYSTEM SELECTOR button on the remote control or using the menu screen operation (page 83)
enables the user to make the following changes depending on S Video / Video input or the currently selected input
module.
The name of the selected system such as RGB, YP
BPRand AUTO is displayed on the top left of the screen and
disappears automatically.
Input module
ET-MD77SD1 :
AUTO 480i 576i
ET-MD77SD3 : S video / Video terminal input signal
: AUTO1 NTSC PAL SECAM
PAL60 NTSC4.43
: AUTO2 NTSC PAL-M
PAL-NFor the setting
of AUTO1
For the setting
of AUTO2
AUTO
576i480i 720/50p 1 080/24sF 1 080/25p 1 080/30p1 080/60i 1 035/60i 720/60p 1 080/24p
1 080/50i
When the STD (standard) button is pressed while changing the system mode (with the SYSTEM
SELECTOR), the projector automatically returns to AUTO1, AUTO2, or AUTO.
“AUTO 1”: Selection is automatically made out of NTSC, PAL, SECAM, NTSC4.43 and PAL60.
“AUTO 2”: Selection is automatically made out of NTSC, PAL-M and PAL-N.
RGB1/RGB2 terminal input signals
For 720p, 1 080i input: RGB YP
BPR
For 480i, 576i, 480p, 576p input: RGB YCbCr
For the signals other than those above, SYSTEM SELECTOR button is invalid.
66
Option settings
OPTION
PROJECTOR ID 2
SETTING FRONT-F
LAMP SELECT DUAL
LAMP POWER HIGH
RS232C SETTING
OSD POSITION 2
SYSTEM INFORMATION
COLOR MATCHING OFF
VIDEO SETTING
AUTO SETUP
:MENU SELECT
:CHANGE
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
:MENU SELECT
ENTER:SUB MENU
Press the “ENTER” button.
The OPTION screen will be displayed.
Select “PROJECTOR ID” with
buttons and change the value with
buttons (ALL, 1, 2, …64).
Press the “MENU” button twice.
This concludes the setting procedure and the on-
screen indications disappear and the normal
screen appears again.
• The ID number can be set to “ALL”, or selected from “1” to “64”.
• If the projectors are given ID numbers, their remote controls must be assigned the same ID numbers,
respectively.
• If the ID number of a projector is set to “ALL”, it can be controlled by the remote control or the PC with
any ID number.
If multiple projectors are used and some of them have their IDs set to “ALL”, they cannot be controlled
separately from the projectors with other ID numbers.
For details on remote control ID setting, see page 16.
ID number setting
The projector has an ID number setting function that helps the user to control two or more projectors either
simultaneously or separately with a single remote control. The ID number is set to ALL by default. Hence the
ID number need not be set when only one projector is used.
Procedure of setting
Note
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select “OPTION” with the
buttons.
67
A: Floor mount front projection (Front – Floor mount)
D: Ceiling mount rear projection (Rear – Ceiling mount) C: Floor mount rear projection (Rear – Floor mount)B: Ceiling mount front projection (Front – Ceiling mount)
Select the setting by displaying the on-screen indications using buttons of the remote control or the control panel on
the main unit.
Procedure of setting
OPTION
PROJECTOR ID 2
SETTING FRONT-F
LAMP SELECT DUAL
LAMP POWER HIGH
RS232C SETTING
OSD POSITION 2
SYSTEM INFORMATION
COLOR MATCHING OFF
VIDEO SETTING
AUTO SETUP
:MENU SELECT
:CHANGE
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
:MENU SELECT
ENTER:SUB MENUPress the “MENU” button.
The MAIN MENU screen will be displayed.
Select “OPTION” with the
buttons.
Press the “ENTER” button.
The OPTION screen will be displayed.
Select “SETTING” with the
buttons and choose a projection
scheme with the buttons.
Each time or button is pressed, the types of
projection scheme, together with its indications, are
toggled through a cycle as follows:
FRONT-F FRONT-C
REAR-C REAR-F
Press the “MENU” button twice.
The on-screen indications disappear and the
normal screen appears again.
Installation Setting
A projection scheme can be chosen depending on the installation of the projector. If the picture is shown upside
down or in reverse, change the projection scheme using the following figures A to D.
68 Option settings Lamp select Two internal lamps in the projector can be used either in “DUAL” or “SINGLE” mode depending on users needs or viewing conditions. In the “SINGLE” mode, the projector may automatically switches between one lamp and the other, or one of the lamps can be specified. “LAMP 1”: One lamp illuminates. (Lamp Unit 1 is always used) “LAMP 2”: One lamp illuminates. (Lamp Unit 2 is always used) “SINGLE”: One of the lamps illuminates. (The lamp with shorter operating hours is automatically selected) “DUAL”: Two lamps illuminate. Lamp power The luminance of the projection lamp can be changed depending on users needs or the viewing conditions. “LOW”: Set when high brightness is not necessary. “HIGH”: Set when high brightness is necessary. Note LAMP SELECT DUAL SINGLELAMP1 LAMP2 LAMP POWER LOW HIGH Note• When set to “LOW”, it is possible to reduce power consumption, reduce operating noise and extend lamp service life. • “LOW” is set automatically when Long Life Lamp Units are used. • If any of “SINGLE”, “LAMP 1” and “LAMP 2” has been selected, when a currently lit lamp expires, or is turned off due to the elapsed time of lamp lighting exceeding 1500 hours (with the lamp output set at “HIGH”), the other lamp will be turned on. If “DUAL” has been selected, when either of the two lamps expires, or is turned off due to the elapsed time of lamp lighting exceeding 1500 hours, the other lamp with elapsed time not exceeding 1500 hours continues lighting. Further, if the elapsed time exceeds 1500 hours for both lamps, the projector will enter a standby state. • If only one lamp is mounted, select “LAMP 1” or “LAMP 2” according to the relevant lamp unit. In “LAMP 1” or “LAMP 2” mode, if the corresponding lamp is not installed, the other lamp will turn on. • If the lamp selection is changed, picture is muted during lamp switching execution. (7-25 sec.) This time period is 4 000 hours when Long Life Lamp Units (page 100) are used.
69
Position of on-screen
indications
The user can specify the position of the on-screen
indications
“1”: Top left of the screen
“2”: Left center of the screen
“3”: Bottom left of the screen
“4”: Top center of the screen
“5”: Center of the screen
“6”: Bottom center of the screen
“7”: Top right of the screen
“8”: Right center of the screen
“9”: Bottom right of the screen
OSD POSITION1
2
8
9
System information
Displays the system information of the projector.
• Pressing the “ENTER” button will move on to the next
page.
SYSTEM INFORMATION
ROM VERSION: 1.00
SET RUNTIME: 1200h
LAMP1 TYPE: LAD7700
LOW: 300h
HIGH: 0h
TOTAL: 300h
LAMP2 TYPE: LAD7700
LOW: 300h
HIGH: 0h
TOTAL: 300h
ENTER: NEXT
SYSTEM INFORMATION
ON COUNT
POWER ON TIMES: 100
LAMP 1 ON: 50( 1)
LAMP 2 ON: 50( 1)
AUX: MD77DV: DN
NUMBER OF
ENTRY SIGNAL: 1/64
ENTER: NEXT
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Press and buttons to select
“OPTION”.
Press the “ENTER” button.
The OPTION screen will be displayed.
Press and buttons to select
“RS232C SETTING”.
Press the “ENTER” button.
The RS232C SETTING screen will be displayed.
Press and buttons to select
communication conditions
Press and buttons to confirm the
setting.
Press the “MENU” button three times.
The on-screen indications disappear, and the
system returns to the normal screen.
RS232C SETTING
(Procedure of setting
communication conditions)
OPTION
PROJECTOR ID 2
SETTING FRONT-F
LAMP SELECT DUAL
LAMP POWER HIGH
RS232C SETTING
OSD POSITION 2
SYSTEM INFORMATION
COLOR MATCHING OFF
VIDEO SETTING
AUTO SETUP
:MENU SELECT
ENTER:SUB MENU
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
:MENU SELECT
ENTER:SUB MENU
RS232C SETTING
(IN) BAUDRATE 38400
(IN) PARITY EVEN
(OUT) BAUDRATE 38400
(OUT) PARITY EVEN
VPS SYSTEM MASTER
GROUP A
MASTER
:MENU SELECT
:CHANGE
70
Option settings
Adjusting color matching
When multiple sets are used simultaneously, this projector allows the user to correct the difference of colours
among the sets.
Procedure of adjustment
OPTION
PROJECTOR ID 2
SETTING FRONT-F
LAMP SELECT DUAL
LAMP POWER HIGH
RS232C SETTING
OSD POSITION 2
SYSTEM INFORMATION
COLOR MATCHING 3COLORS
VIDEO SETTING
AUTO SETUP
:MENU SELECT :CHANGE
ENTER:SUB MENU
Press the “MENU” button.
The MAIN MENU screen will be displayed.
Select “OPTION” with the
buttons.
MAIN MENU
PICTURE
POSITION
ADVANCED MENU
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
SECURITY
Press “ENTER” button.
The OPTION screen will be displayed.
Select “COLOR MATCHING” with the
buttons.
Select “3COLORS” with the
buttons.
COLOR MATCHING:3COLORS
R
G
B
AUTO TESTPATTERN OFFPress the “ENTER” button.
Select “R”, “G” and “B” with the
buttons.
Press “ENTER” button.
Adjust the values with the
buttons.
These values can be adjusted from 0 to 2048.
3COLORS:R
R 2048
G 0
B 0
:MENU SELECT
:ADJUST
Adjustment
• The effects of correcting the adjustment color.
When tuning the correction color that is the same as the adjustment color: the brightness of the adjustment color
changes.
When tuning the correction color RED: RED is added to or reduced from the adjustment color.
When tuning the correction color GREEN: GREEN is added to or reduced from the adjustment color.
When tuning the correction color BLUE: BLUE is added to or reduced from the adjustment color.
• This adjustment should be carried out by a person who is familiar with the projector or by a service person
because a high level of skill is required to make successful adjustment.
• Pressing the “STD” (standard) button will restore the factory defaults for all items.
• When any setting other than “OFF” has been selected for color matching, the COLOR TEMP. setting is fixed at
“USER1”
Note
Note• When “7COLORS” is selected in step ,
it is possible to adjust the 7colours of “R”,
“G”, “B”, “Cy”, “Mg”, “Ye” and “Wh”.