Panasonic Progressive Wide Plasma Display Th 37ph9 Operating Instructions

							41
1
2
3
5Press to display the Setup menu.
Press to select “OSD Language”.
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
Press to adjust the menu.
Press to confi rm.
Press to exit from 
Options menu.
4
6
Item Effect Adjustments
Off-timer
function
EnableDisable
Enable: Switches the “Off-timer function” “On”
Disable: Switches the “Off-timer function” “Off”
Note:  When “Disable” is set, the Off-timer is cancelled.
Onscreen
display
On Off
On:  Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after 
 was pressed.
Off:  Hides all the items above from view.
Initial INPUTOff  PC  INPUT1  INPUT2  INPUT3
Adjusts the input signal when TV is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 18).
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
1/3Options
Off-timer function
INPUT lock
Studio W/B
Advanced PIP
Display size Initial VOL level
Maximum VOL level Initial INPUT Onscreen display
Off
Off
Off
Off Enable
On
Off
0
Off Off
0
Options Adjustments 
						

							42
Item Effect Adjustments
Initial VOL 
level
Off On
Press button to adjust the volume when TV is turned on.
Off  On
Off: Sets normal volume.
On: Sets your preferred volume.
Notes:
•
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.•You can hear the changed volume regardless of your volume setting before opening the options menu if you 
adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL 
level
Off On
Press button to adjust the maximum volume.
Off  On
Off: Sets auto maximum volume.
On: Sets your preferred maximum volume.
Notes:
•  If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically 
becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
•
You can hear the changed volume regardless of your volume setting before opening the options menu if you 
adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
INPUT lockOff  PC  INPUT1  INPUT2  INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 18).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
•  In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value input 
in the single screen display mode.
Studio W/B
Off On
Off:  Nullify all the settings adjusted.
On: Sets the color temperature for TV studio.
Note:  Valid only when the low is set as color temperature on screen adjustment.
Advanced PIP
Off On
Off: Sets normal two screen display mode (see page 21).
On: Sets Advanced PIP mode (see page 22).
Notes:
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
•
, buttons are unavailable during Advanced PIP mode operation.
Display size
Off On
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
    Off       On
Notes:
• This setting is valid only when the input signals are as follows; 525i, 525p, 625i, 625p, 750/60p, 
750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p, 1250/50i (Component Video, 
RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom or Multi screen is selected.
• When Display size is set to “On”, Pos. /Size adjustment cannot be used. 
• Refer to each board's operating instruction for DVI, SDI, HDMI's corresponding signals.
1/3Options
Off-timer function
INPUT lock
Studio W/B
Advanced PIP
Display size Initial VOL level
Maximum VOL level Initial INPUT Onscreen display
Off
Off
Off
Off Enable
On
Off
0
Off Off
0
Options Adjustments 
						

							43
2/3Options
OffOffOff
Off
0
Remote ID
Serial ID ID select Button lock
Remocon User level
Item Effect Adjustments
Button lockOff   MENU&ENTER   On
Off:  All the buttons at the bottom of the main unit can be used.
MENU & ENTER:
  Locks 
MENU and ENTER/ buttons on bottom face of main unit.
On:  Locks all the button on bottom face of main unit.
Remocon
User levelOff   User1   User2   User3 
Off:  You can use all of the buttons on the remote control.
User1:You can only use 
,,,,,,, buttons on the remote control.
User2:You can only use
,, buttons on the remote control.
User3:Locks all the buttons on remote control.
ID selectSets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
Remote ID
Off On
Off:  Disables ID remote control functions. You can use normal remote control operations.
On:  Enable ID remote control functions.
Serial ID
Off On
Sets the panel ID Control.
Off:  Disables external control by the ID.
On:  Enables the external control by the ID.
Item Effect Adjustments
Slot PowerOff  Auto  On
Off:  Power is not transmitted to the slot power.
Auto:  Power is transmitted to the slot power only when main power is on.
On:  Power is transmitted to the slot power when main power is on or in the standby state.
Note:
In some cases, power is transmitted to the slot power when main power is on or in the standby state regardless of the slot power setting.
V.InstallationOff On
Off:  Sets fan to the horizontal installation mode.
On:  Sets fan to the vertical installation mode.
Notes:
• This functions when display is turned on.
• This mode is available for TH-42PH9UK, TH-50PH9UK.
• Vertical installation is available for TH-42PS9UK without this mode setting.
• Turn up the power switch for the upward direction when you set Display vertically.
Rotate
Off On
Off:  Does not rotate the image.
On:  Rotates the image 180 degrees.
Serial Slot 
SelectSlot1  Slot2   Slot3
Selects the slot which communicates serial.
Note:
The setting of an external command can be set only from the fi xed serial terminal (see page 11)
3/3Options
Off
Off
Off V. lnstallation
Rotate
Slot1 Serial Slot Select Slot power
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote 
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the 
 button on main unit together with  button on the remote control and hold for more than 5 seconds. The 
“SHIPPING” menu is displayed and the lock is released when it disappears.
Options Adjustments 
						

							44
Shipping condition
This function allows you to reset the unit to the factory setting.
1
2
3
4
Press to display the SET UP menu.
Press to select “OSD LANGUAGE”.
Press and hold till the SHIPPING menu is 
displayed.
Press to select “YES”.
Press to confi rm.
[from the unit]
1  Press the MENU button till the Setup menu is displayed.
2  Press the Volume Up “+” or Down “–” button to select “OSD LANGUAGE”.
3  Press and hold the ENTER button till the SHIPPING menu is displayed.
4  Press the Volume Up “+” or Down “–” button to select “YES”.
5  Press the ENTER button.
Note:
Press the R button to return to SET UP menu when SHIPPING menu is displayed.
1/2
PC
OFF
STANDBY SAVE
OFF
POWER MANAGEMENTOFF
AUTO POWER OFF
OFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB
INPUT LABELSIGNAL
POWER SAVE
SET UP
SHIPPINGYES 
						

							45
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Checks
Picture Sound
InterferenceNoisy SoundElectrical Appliances
Cars / Motorcycles
Fluorescent light
Normal PictureNo SoundVolume
(Check whether the mute function has been activated on the remote control.)
No PictureNo SoundNot plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
No PictureNormal SoundIf a signal with a non-applicable color system format, or frequency is input, only the input 
terminal indication is displayed.
No ColorNormal SoundColor controls set at minimum level. (see page 23, 24)
COLOR SYSTEM (see page 39)
No remote control operations can be performed. Check whether the batteries have discharged completely and, if they have not, whether they 
were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a strong fl uorescent 
light.
Check whether the remote control designed specifi cally for use with the unit is being used. 
(The unit cannot be operated by any other remote control.)
A cracking sound is sometimes heard from the unit. If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing 
very slight contractions in response to changes in the room temperature.  There are no adverse 
effects on the performance or other aspects.
The top or bottom of the picture on the screen is cut 
off when I use the zoom function.Adjust the position of the picture on the screen.
Areas at the top and bottom of the screen where 
the image is missing appear when I use the zoom 
function.When using a video software program (such as a cinema size program) with a screen wider 
than one in the 16:9 mode, blank areas separate from the images are formed at the top and 
bottom of the screen.
I can hear sounds coming from inside the unit. When the power is turned on, a sound of the display panel being driven may be heard: This is 
normal and not indicative of malfunctioning.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the type of input 
signal. However, this is not a malfunction.
Plasma Display panel
Symptoms Check
The screen darkens slightly when bright pictures with 
minimal movements are shown.The screen will darken slightly when photos, still images of a computer or other pictures with 
minimal movements are shown for an extended period. This is done to reduce after-image 
on the screen and the shortening of the screen’s service life: It is normal and not indicative of 
malfunctioning.
It takes a while for the picture to appear. The unit digitally processes the various signals in order to reproduce esthetically pleasing
images. As such, it sometimes takes a few moments for the picture to appear when the power 
has been turned on, when the input has been switched or when the images for the main picture 
and sub picture on the two screens are swapped.
The  edges  of  the  images  fl icker. Due to the characteristics of the system used to drive the panel, the edges may appear to fl icker 
in the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
The brightness on both sides of images in NORMAL 
mode changes.When viewing the side panels at the “BRIGHT” or “MID” setting, the brightness on both sides 
may change depending on the kind of program shown: This is normal and not indicative of 
malfunctioning.
Some parts of the screen do not light up. The plasma display panel is manufactured using an extremely high level of precision technology, 
however, sometimes some parts of the screen may be missing picture elements or have luminous 
spots. This is not a malfunction.
After-images appearDo not allow a still picture to be displayed for an extended period, as this can cause a permanent 
after-image to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images 
displayed in NORMAL mode.
Note:
The permanent after-image on the Plasma Display resulting from fi xed image use is not an 
operating defect and as such is not covered by the Warranty.
This product is not designed to display fi xed images for extended periods of time.
[for TH-37PH9UK, TH-42PH9UK, TH-50PH9UK]Whirring sounds can be heard from the display unit.The display unit is fi tted with a cooling fan to dissipate heat generated during normal use. The 
whirring sound is caused by rotation of the fan and is not a malfunction. 
						

							46
VIDEO/COMPONENT/RGB/PC input signals
VIDEO input
Signal nameHorizontal Vertical
frequency(kHz) frequency(Hz)
1 NTSC 15.73 59.94
2 PAL 15.63 50.00
3 PAL60 15.73 59.94
4 SECAM 15.63 50.00
5 Modifi ed NTSC 15.73 59.94
Applicable input signals for Component / Mini D-sub 15P (Component) / RGB / Mini D-sub 15P (RGB) (

Mark)
Signal nameHorizontal
frequency (kHz)Vertical
frequency (Hz)Component / 
Mini D-sub 15P 
(Component)RGB / 
Mini D-sub 15P 
(RGB)
1 525 (480) / 60i 15.73 59.94


2 525 (480) / 60p 31.47 59.94

1
3 625 (575) / 50i 15.63 50.00


4 625 (575) / 50p 31.25 50.00

5 750 (720) / 60p 45.00 60.00

6 750 (720) / 50p 37.50 50.00

7 1,125 (1,080) / 60i 33.75 60.00

8 1,125 (1,080) / 50i 28.13 50.00

9 1,125 (1,080) / 24p 27.00 24.00

10 1,125 (1,080) / 24sF 27.00 47.92

11 1,125 (1,080) / 25p 28.13 25.00

12 1,125 (1,080) / 30p 33.75 30.00

13 1,250 (1,080) / 50i 31.25 50.00

14 640 × 400 @70 Hz 31.46 70.07
15 640 × 480 @60 Hz 31.47 59.94
2
16 640 × 480 @72 Hz 37.86 72.81

17 640 × 480 @75 Hz 37.50 75.00
18 640 × 480 @85 Hz 43.27 85.01
19 852 × 480 @60 Hz 31.47 59.94
2
20 800 × 600 @56 Hz 35.16 56.25

21 800 × 600 @60 Hz 37.88 60.32
22 800 × 600 @72 Hz 48.08 72.19
23 800 × 600 @75 Hz 46.88 75.00
24 800 × 600 @85 Hz 53.67 85.06
25 1,024 × 768 @60 Hz 48.36 60.00
26 1,024 × 768 @70 Hz 56.48 70.07
27 1,024 × 768 @75 Hz 60.02 75.03
28 1,024 × 768 @85 Hz 68.68 85.00
29 1,152 × 864 @75 Hz 67.50 75.00
30 1,280 × 960 @60 Hz 60.00 60.00
31 1,280 × 960 @85 Hz 85.94 85.00
32 1,280 × 1,024 @60 Hz 63.98 60.02
33 1,280 × 1,024 @75 Hz 79.98 75.03
34 1,280 × 1,024 @85 Hz 91.15 85.02
35 1,600 × 1,200 @60 Hz 75.00 60.00
36  1,600 × 1,200 @65 Hz 81.25 65.00
37 1,066 × 600 @60 Hz 37.88 60.32
38 1,366 × 768 @60 Hz 48.36 60.00
39 Macintosh13” (640 × 480) 35.00 66.67
40 Macintosh16” (832 × 624) 49.72 74.54
41 Macintosh21” (1,152 × 870) 68.68 75.06

1:When selected the RGB format and 525p signal input to the Mini D-sub 15P terminal, it is recognized as VGA 60Hz signal.

2:When inputted VGA 60Hz format signal from the other than Mini D-sub 15P terminal, it is recognized as 525p signal.
Note: Signals without above specifi cation may not be displayed properly. 
						

							47
Specifi cations
TH-42PS9UK
Power Source 120 V AC, 50/60 Hz
Power Consumption
Power on 290W 
Stand-by condition Save OFF 0.6 W, Save ON 0.4 W
Power off condition 0.1 W
Plasma Display panelDrive method : AC type 42-inch,
16:9 aspect ratio
Contrast Ratio Max 10000:1
Screen size
36.2” (920 mm) (W) × 20.4” (518 mm) (H) 
× 42” (1,056 mm) (diagonal)
(No.of pixels) 408,960 (852 (W) × 480 (H))
[2,556 × 480 dots]
Operating condition
Temperature 32 °F - 104 °F (0 °C - 40 °C)
Humidity 20 % - 80 %
Applicable signals
Color System NTSC, PAL, PAL60, SECAM, Modifi ed NTSC
Scanning format 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 50i · 24p · 25p 
· 30p · 24sF ···· SMPTE274M, 1250 (1080) / 50i 
PC signals VGA
SVGA, XGA, SXGA, UXGA  ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
AV VIDEO IN (BNC)   1.0 Vp-p (75 
 or high impedance)
S VIDEO IN (MINI DIN 4PIN)      Y: 1 Vp-p (75 
), C: 0.286 Vp-p (75 
)
AUDIO IN (RCA PIN JACK × 4)   0.5 Vrms (high impedance)
COMPONENT/RGB Y/G (BNC)   1.0 Vp-p/with/sync (75 
)
0.7 Vp-p/without/sync (75 
)
P
B/B (BNC), PR/R (BNC)   0.7 Vp-p (75 
)
AUDIO IN (RCA PIN JACK × 2)   0.5 Vrms (high impedance)
PC (HIGH-DENSITY Mini-D-SUB 15PIN)  R,G,B/0.7 Vp-p (75 
)
   HD, VD/1.0 - 5.0 Vp-p (high impedance)
 Component 
  Y :  1.0 Vp-p (75 
 : include sync)
 P
B/CB :   0.7  Vp-p (75 
)
 P
R/CR :   0.7  Vp-p (75 
)
AUDIO IN (M3 JACK)     0.5 Vrms (high impedance)
SERIAL EXTERNAL CONTROL TERMINAL (D-SUB 9PIN)  RS-232C COMPATIBLE
SPEAKERS (6 
) 16W [8 W + 8 W] (10 % THD)
Accessories Supplied
Remote Control TransmitterEUR7636070R
Batteries 2 × AA Size
Fixing bands (TMME203 or TMME187) × 2
Dimensions (W × H × D)
40.2” (1,020 mm) × 24” (610 mm) × 3.5” (89 mm)
Mass (weight)
main unit only approx. 57.3 lbs
with speakers approx. 66.1lbs
Note:
Design and specifi cations are subject to change without notice. Mass and dimensions shown are approximate. 
						

							48
Specifi cations
TH-37PH9UK TH-42PH9UK
Power Source 120 V AC, 50/60 Hz
Power Consumption
Power on 300W 345W
Stand-by condition Save OFF 0.6 W, Save ON 0.4 W Save OFF 0.6 W, Save ON 0.4 W
Power off condition 0.1 W 0.1 W
Plasma Display panelDrive method : AC type 37-inch,
16:9 aspect ratioDrive method : AC type 42-inch,
16:9 aspect ratio
Contrast Ratio
Max 10000:1
Screen size
32.2” (818 mm) (W) × 18.1” (461 mm) (H)
× 37” (939 mm) (diagonal)36.2” (920 mm) (W) × 20.4” (518 mm) (H) 
× 42” (1,056 mm) (diagonal)
(No.of pixels) 737,280 (1,024 (W) × 720 (H))
[3,072 × 720 dots]786,432 (1,024 (W) × 768 (H))
[3,072 × 768 dots]
Operating condition
Temperature 32 °F - 104 °F (0 °C - 40 °C)
Humidity 20 % - 80 %
Applicable signals
Color System NTSC, PAL, PAL60, SECAM, Modifi ed NTSC
Scanning format 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 50i · 24p · 25p 
· 30p · 24sF ···· SMPTE274M, 1250 (1080) / 50i 
PC signals VGA, SVGA,
XGA, SXGA, UXGA  ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 HzVGA, SVGA, XGA,
SXGA, UXGA  ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
AV VIDEO IN (BNC)   1.0 Vp-p (75 
 or high impedance)
S VIDEO IN (MINI DIN 4PIN)      Y: 1 Vp-p (75 
), C: 0.286 Vp-p (75 
)
AUDIO IN (RCA PIN JACK × 4)   0.5 Vrms (high impedance)
COMPONENT/RGB Y/G (BNC)   1.0 Vp-p/with/sync (75 
)
0.7 Vp-p/without/sync (75 
)
P
B/B (BNC), PR/R (BNC)   0.7 Vp-p (75 
)
AUDIO IN (RCA PIN JACK × 2)   0.5 Vrms (high impedance)
PC (HIGH-DENSITY Mini-D-SUB 15PIN)  R,G,B/0.7 Vp-p (75 
)
   HD, VD/1.0 - 5.0 Vp-p (high impedance)
 Component 
  Y :  1.0 Vp-p (75 
 : include sync)
 P
B/CB :   0.7  Vp-p (75 
)
 P
R/CR :   0.7  Vp-p (75 
)
AUDIO IN (M3 JACK)     0.5 Vrms (high impedance)
SERIAL EXTERNAL CONTROL TERMINAL (D-SUB 9PIN)  RS-232C COMPATIBLE
SPEAKERS (6 
) 16W [8 W + 8 W] (10 % THD)
Accessories Supplied
Remote Control TransmitterEUR7636070R
Batteries 2 × AA Size
Fixing bands (TMME203 or TMME187) × 2
Dimensions (W × H × D)
36.2” (920 mm) × 21.7” (550 mm) × 3.5” (89 mm)40.2” (1,020 mm) × 24” (610 mm) × 3.5” (89 mm) 
Mass (weight)
main unit only approx. 50.7 lbs approx. 59.5 lbs
with speakers approx. 59.5 lbs approx. 68.3 lbs
Note:
Design and specifi cations are subject to change without notice. Mass and dimensions shown are approximate. 
						

							49
Specifi cations
TH-50PH9UK
Power Source 120 V AC, 50/60 Hz
Power Consumption
Power on 460W
Stand-by condition Save OFF 0.5 W, Save ON 0.3 W
Power off condition 0.1 W
Plasma Display panelDrive method : AC type 50-inch,
16:9 aspect ratio
Contrast Ratio
Max 10000:1
Screen size43.5” (1,106 mm) (W) × 24.5” (622 mm) (H) 
× 50” (1,269 mm) (diagonal)
(No.of pixels) 1,049,088 (1,366 (W) × 768 (H))
[4,098 × 768 dots]
Operating condition
Temperature 32 °F - 104 °F (0 °C - 40 °C)
Humidity 20 % - 80 %
Applicable signals
Color System NTSC, PAL, PAL60, SECAM, Modifi ed NTSC
Scanning format 525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 750 (720) / 60p · 50p, 1125 (1080) / 60i · 50i · 24p · 25p 
· 30p · 24sF ···· SMPTE274M, 1250 (1080) / 50i 
PC signals VGA, SVGA, XGA, 
SXGA, UXGA  ···· (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
AV VIDEO IN (BNC)   1.0 Vp-p (75 
 or high impedance)
S VIDEO IN (MINI DIN 4PIN)      Y: 1 Vp-p (75 
), C: 0.286 Vp-p (75 
)
AUDIO IN (RCA PIN JACK × 4)   0.5 Vrms (high impedance)
COMPONENT/RGB Y/G (BNC)   1.0 Vp-p/with/sync (75 
)
0.7 Vp-p/without/sync (75 
)
P
B/B (BNC), PR/R (BNC)   0.7 Vp-p (75 
)
AUDIO IN (RCA PIN JACK × 2)   0.5 Vrms (high impedance)
PC (HIGH-DENSITY Mini-D-SUB 15PIN)  R,G,B/0.7 Vp-p (75 
)
   HD, VD/1.0 - 5.0 Vp-p (high impedance)
 Component 
  Y :  1.0 Vp-p (75 
 : include sync)
 P
B/CB :   0.7  Vp-p (75 
)
 P
R/CR :   0.7  Vp-p (75 
)
AUDIO IN (M3 JACK)     0.5 Vrms (high impedance)
SERIAL EXTERNAL CONTROL TERMINAL (D-SUB 9PIN)  RS-232C COMPATIBLE
SPEAKERS (6 
) 16W [8 W + 8 W] (10 % THD)
Accessories Supplied
Remote Control TransmitterEUR7636070R
Batteries 2 × AA Size
Fixing bands (TMME203 or TMME187) × 2
Dimensions (W × H × D)
47.6” (1,210 mm) × 28.5” (724 mm) × 3.7” (95 mm) 
Mass (weight)
main unit only approx. 81.6 lbs
with speakers approx. 90.4 lbs
Note:
Design and specifi cations are subject to change without notice. Mass and dimensions shown are approximate. 
						

							Panasonic Broadcast & Television Systems
Company, Unit of Panasonic Corporation of 
North America 
One Panasonic Way 2A-4
Secaucus, NJ  07094Panasonic Puerto Rico, Inc. 
Ave. 65de Infanteria, Km.9.5
San Gabriel Industrial Park
Carolina, Puerto Rico 00985
PANASONIC PLASMA SCREEN
Limited Warranty
Panasonic Broadcast & Television Systems Company or 
Panasonic Puerto Rico, Inc. (collectively referred to as 
“the Warrantor”) will repair this product and all included 
accessories with new or refurbished parts, free of charge 
in the USA or Puerto Rico, of the original purchase in 
the event of a defect in materials or workmanship as 
follow:
Models or PartsPart
WarrantyLabor
Warranty
Plasma Screen
1 Year 1 Year
Carry-in or mail-in service in the USA may be obtained 
during the warranty period by contacting Panasonic 
Broadcast & Television Systems Company Factory 
Servicenter listed in the Service Directory or call toll 
free1-800-526-6610 to locate an authorized Servicenter.
Carry-in or mail-in service in Puerto Rico can be 
obtained during the warranty period by 787-750-5135
This warranty is extended only to the original purchaser 
and is non transferable.  A purchase receipt or other 
proof of date of original purchase will be required before 
warranty service is rendered.
This warranty only covers failures due to defects in 
materials or workmanship, which occur during normal 
use.  The warranty does not cover damage which occur 
in shipment, or failures which are caused by products 
not supplied by the warrantor, or failures which result 
installation, set-up adjustments, improper antenna,inadequate signal pickup, maladjustment of consumer 
controls, improper operation, power line surge, improper 
voltage supply, lighting damage, or service by anyone 
other than an authorized repair facility, or damaged this 
attributable to acts of God.
LIMITS AND  EXCLUSIONS
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR 
INCIDENTAL OR CONSEQUENTIAL DAMAGES 
(INCLUDING, WITHOUT LIMITION, DAMAGE 
TO DISCS) RESULTING FROM THE USE OF THIS 
PRODUCT, OR ARISING OUT OF ANY BREACH OF 
THE WARRANTY.  ALL EXPRESS AND IMPLIED 
WARRANTIES, INCLUDING THE WARRANTIES 
OF MERCHANTABILITY AND FITNESS FOR 
PARTICULAR PURPOSE, ARE LIMITED TO THE 
APPLICABLE WARRANTY PERIOD SET FORTH 
ABOVE.
Some states do not allow the exclusion or limitation 
of incidental or consequential damages, or limitations 
on how long an implied warranty lasts, so the above 
exclusions or limitations may nor apply to you. This 
warranty gives you specific legal rights and you may 
other rights, which vary from state to state.
If you have a problem with this product that is not 
handled to your satisfaction, then write the Consumer 
Affairs Department at the Company address indicated 
above.
In the USA
FOR THE NEAREST SERVICE CENTER
1-800-526-6610
Regional Offi ces
 New Jersey
50 Meadowlands Pkwy – 2A4
Secaucus, NJ  07094
201-348-7975 Illinois
1713 N.  Randall – E1-E1
Elgin, IL  60123 
847-468-5270Georgia
1225 Northbrook Pkwy 
Suwanee, GA  30093 
770-338-6855California
3330 Cahuenga Blvd West
Los Angeles, CA  90068
323-436-3505
In Puerto Rico
For service call 787-750-5135