Panasonic Pc Software Package Wv Asm10 Operating Instructions

							51
Note:
The [Add…] button will become unavailable when
reached the maximum number of the sequence
registration (10 sequences).
The following are descriptions about each item dis-
played on the Sequence regist. window.
Sequence title
Enter the sequence title. When editing the title, enter
up to 16 characters. The following characters are
unavailable for the sequence title.
! $ % ’< = > @ [  ] ^ _ ` { | } ~
The sequence title already in use cannot be entered.
Registered group
The groups that can be registered in the sequence will
be displayed in list form.
Number of area
Select the number of the cameras of the group to dis-
play the groups in the list below.
1-screen:The group whose screen pattern is 1-
screen.
4-screen:The group whose screen pattern is 4-
screen.
6-screen:The group whose screen pattern is 6-
screen.
9-screen:The group whose screen pattern is 9-
screen.
16-screen:The group whose screen pattern is 16-
screen.
Default:1-screen
Number of group
Number of the groups registered in the sequence will
be displayed in list form.
[Add step] button
A group selected from Registered group can be
added to Step.
Notes:
•The group already registered in the sequence can
be registered to the same sequence again as a dif-
ferent step.
•The [Add step] button will become unavailable
when reached the maximum number of the step
addition (64 steps).
Step
Each step of the registered sequence will be dis-
played.
[Delete step] button
The selected group can be deleted from the sequence.
[Up] button
The selected group will move one step up.
[Down] button
The selected group will move one step down.
[Set] button
The edited setting will be saved and applied.
Step 4
Click the [Set] button after editing the information.
→The Sequence regist. window will close and the
settings will be saved and applied. The sequence
will be displayed in the list of the registered
sequence.
Note:
When a message window is displayed by clicking
the [Set] button, refer to the Displayed messages
and solutions section on page 73 and follow the
instructions. 
						

							52
Edit the sequence
Step 1
Display the Sequence page. (page 50)
Step 2
Select the sequence whose information is to be edited,
and then click the [Edit…] button.
→The Sequence regist. window will be displayed.
Step 3
Click the [Set] button after editing the information.
Refer to the Register a sequence section (page
50) for further information.
→The Sequence regist. window will close and the
settings will be saved and applied.
Note:
When a message window is displayed by clicking
the [Set] button, refer to the Displayed messages
and solutions section on page 73 and follow the
instructions.
Delete the sequence
Step 1
Display the Sequence page. (page 50)
Step 2
Select the sequence to be deleted. 
Step 3
Click the [Delete…] button.
→The confirmation window will be displayed.
Step 4
Click the [OK] button.
→The selected sequence will be deleted.
Notes:
•When the sequence set as the default screen is
deleted, -- will be displayed for the setting of
Default screen on the Live window page. In this
case, a black screen will be displayed in the image
display area of the operation window just after
login.
•When a message window is displayed by clicking
the [Delete…] button, refer to the Displayed mes-
sages and solutions section on page 73 and follow
the instructions. 
						

							53
Settings relating to the window
The settings relating to the live window can be configured.
Use the live window [Live window]
Click the [Window] button to display the Live window page.
Default screen
Select Group or Sequence to determine how to dis-
play live images when starting the operation software.
Group:The group display will start to display live
images just after login.
Sequence:The sequence display will start to display
live images just after login.
Default:Group

It is possible to select the group registered on the
Group regist. window.
When no group is registered, only -- will be displayed
in the drop-down list. In this case, a black screen will
be displayed in the image display area of the operation
window.
Refer to the Register a group [Group] section 
(page 46) for how to register groups.
Default:--

It is possible to select the sequence registered on the
Sequence regist. window. When no sequence is reg-
istered, only -- will be displayed in the drop-down list.
In this case, a black screen will be displayed in the
image display area of the operation window.
Refer to the Register a sequence [Sequence] section
(page 50) for how to register sequences.
Default:--Sequence dwell time
Select a sequence dwell time from the following.
This setting can be set only when Sequence is
selected for Default screen.
3s/5s/10s/15s/20s
Default:3s
[Set] button
The edited setting will be saved and applied. 
						

							54
Settings relating to the communication
Configure the settings relating to the communication required to use this software.
Network settings [Basic setup]
Click the [Comm] button to display the Basic setup page.
Configure the settings of Proxy address and Proxy port number.
Proxy address
Enter the IP address of the proxy server.
Enter up to 255 alphanumeric characters.
Proxy port number
Enter the port number of the proxy server.
Enter a number from 1 to 65535.
[Set] button
The edited settings will be saved and applied.
Notes:
•The network settings will not be validated if no
value is entered for Proxy address and Proxy
port number even when ON is selected for Use
a proxy server.
•When using the proxy server, use an HTTP proxy
server. 
						

							55
Settings relating to maintenance
The following can be performed on the Maintenance page. 
•Display the version of this software
•Save/load/initialize the setup file of the setup software
Display the version of this software [Version information]
Click the [Maintenance] button, and then click the [Version information] tab to display the Version information page.
Software version
Version of this software will be displayed. 
						

							56
Save/load/initialize the setup data [Save/Load]
The setup data can be saved/loaded/initialized.
Save the setup data as a backup
Important:
Back up the setup data periodically by copying it onto an external hard disk drive or other storage medium. When
the hard disk drive on the PC in use is damaged, it may be impossible to recover the setup data.
Step 1
Click the [Maintenance] button.
Step 2
Click the [Save/Load] tab.
→The Save/Load page will be displayed.The following are descriptions about each item dis-
played on the Save/Load page.
[Save…] button
The Save As window will be displayed.
[Load…] button
The Open window will be displayed.
[Execute…] button
The initialization start confirmation window will be dis-
played.
Step 3
Click the [Save...] button.
→The Save As window will be displayed.
Step 4
Click the [Save] button after designating the destina-
tion folder and the file name.
→Saving of the setup data will start. 
						

							57
Note:
When a message window is displayed by clicking
the [Save] button, refer to the Displayed messages
and solutions section on page 73 and follow the
instructions.Step 5
Click the [OK] button on the confirmation window.
→The Save/Load page will be displayed again.
Load the setup file
Important:
•When loading of the setup file starts, all the setup data of this software will be overwritten.
•When loading of the setup file is completed, the setup software will restart.
Step 1
Display the Save/Load  page. (page 56)
Step 2
Click the [Load...] button.
→The Open window will be displayed.
Step 3
Select the setup file to be loaded, and then click the
[Open] button.
→The loading start confirmation window will be dis-
played.
Step 4
Click the [OK] button on the confirmation window.
→Loading of the setup file will start.
Step 5
When the loading completion window is displayed,
click the [OK] button.
→The setup software will be restarted and the login
window will be displayed. 
						

							58
Initialize the setup file
Important:
•When initialization of the setup file starts, all the setup data of this software will be initialized. It is recommended
to back up the setup file before initializing the setup file.
•When initialization of the setup file is completed, the setup software will restart.
Step 1
Display the Save/Load  page. (page 56)
Step 2
Click the [Execute…] button.
→The initialization start confirmation window will be
displayed.
Step 3
Click the [OK] button.
→Initialization of the setup file will start.
Step 4
When the initialization is completed, the confirmation
window will be displayed.
Click the [OK] button on the confirmation window.
→The setup software will be restarted and the login
window will be displayed. 
						

							Settings relating to the external interface
59
When controlling functions of this software using an external interface, it is necessary to configure the settings relat-
ing to the external interface such as, ON/OFF for use of the external interface, the group number setting and the
sequence number setting.
External interface settings [Basic setup]
Click the [External I/F] button, and then click the [Basic setup] tab to display the Basic setup page.
External I/F
Select ON or OFF to determine whether or not to
use an external interface.
ON:Use an external interface
OFF:Not use an external interface
Default:ON
Port number
Enter a number from 1 to 65535 for the port number.
Default:10101
[Set] button
The edited settings will be saved and applied. 
						

							60
Step 1
Click the [External I/F] button.
Step 2
Click the [Group number] tab.
→The Group number page will be displayed.
The following are descriptions about each item dis-
played on the Group number page.
[Auto numbering] button
Group numbers will automatically be assigned in order
of the displayed list.[File export] button
The displayed list will be saved as a file in CSV format.
[Set] button
The edited settings will be saved and applied.
Step 3
Click the desired group title, and then click the group
number column respective to the clicked group title.
→The clicked column will become editable.
Step 4
Enter the desired group number.
1-99999 are available.
Step 5
Click the [Set] button.
Group number setting [Group number]
Assign group numbers to the registered group names.
Manual assignment