Panasonic Network Disk Recorder Wj Nd200 Setup Instructions

							81
•The ActiveX control is not installed in the PC. Install
the ActiveX control by referring to the following
page.
•Are the connected network cameras configured cor-
rectly?
Check the settings of the setup menu (Camera -
NW Camera Setup).
•Are the settings of the setup menu (Schedule -
Program - LIVE VIDEO) configured correctly?
Check the settings.
•Are the network settings of the cameras and the unit
configured correctly?
Check the settings of IP address, subnet mask and
default gateway for them.
•When M-JPEG is selected for the image compression
method of the camera, live images may not be dis-
played in the image display area and black screen will
be displayed for a few minutes in the following cases.
•When frequently checked if the appropriate values are
set for the recording settings (by clicking the
[Measurement] button on the Program Setup page
(Schedule - Program)).
•When the settings of the unit are saved repeatedly.
Wait around 10 minutes without any operations. The
unit will function normally.
Cause/solution
The message Please Wait.
remains on the screen.
No live image is displayed.
83
47
48, 56
–
40
Reference
pagesSymptom
•When logged in with Limited user account of
Windows operating system, images will not be dis-
played since the ActiveX control may not be installed
correctly. Log in with Computer administrator user
account.
Live/recording images are
not displayed.– 
						

							•Change the port number for the camera, and then
click the [SETUP] button again.
82
•Are the settings of the network camera set correctly?
Check the model of the set camera on the setup
menu (Camera - NW Camera Setup).
•When the image compression method of all cameras
in use is not the same, performance may become
lower. (Refresh of images will be unstable.)
•The configured settings for transmission rate/record-
ing rate may be beyond the maximum network perfor-
mance.
Lower the value/rate of the settings relating to the net-
work such as the transmission rate, recording rate,
etc.
Reference
pages Cause/solutionSymptom
•The line speed settings may be not the same between
the unit and the hub, for example, 100M BASE-TX
Full for the unit and 100M BASE-TX half, etc. Some
hubs change the line speed automatically depending
on the network traffic and it may cause configuration
errors. Check the line speed settings of both the unit
and the hub, and configure the line speed settings of
both to conform them.
Refresh of live images is
unstable.
Browser disconnection
sometimes occurs.
Network performance is
poor.
Image file downloaded from
the FTP server is faulty.
–
43
–
•Is ON selected for Enable format button on the
Config page?
When OFF is selected, it is impossible to format the
hard disk using the FORMAT button. Check the
Enable format button setting on the Config page. •Are the user ID and the password for the network
camera set correctly?
Check if the user ID and password are set correctly
on the setup menu (Camera - NW Camera Setup).
Cannot operate the camera.
The setup menu of the cam-
era is not displayed even
though the [SETUP] button
on the NW Camera Setup
page is clicked.
Cannot format the hard disk
using the FORMAT button
inside the front cover.
47
50
76 50 
						

							83
•Click the information bar and select Install ActiveX
Control….
The Security Warning window will be displayed.
Click the [Install] button on the displayed Security
Warning window. •Click the information bar and select Always Allow
Pop-ups from This Site…. The dialog window saying
Allow pop-ups from this site? will be displayed. Click
the [Yes] button.
Solutions
When using a PC on which Windows XP Service Pack2 (SP2) is installed
The following may occur during operation when using a PC on which Windows XP Service Pack2 (SP2) is installed.
Follow the instructions below when the following occurred. By performing the following solutions, other applications
and the security level may not be affected.
The Information Bar expressed in the following symptom and solutions will be displayed just below the address bar
only when there is information to communicate.
The following message is
displayed on the information
bar.
Pop-up blocked. To see
this pop-up or additional
options, click here…
The following message is
displayed on the information
bar.
This site might require the
following Active X control:
wvasetup.exe from
Matsushita Electric
Industrial Co., Ltd. Click
here to install...
–
–
Reference 
pagesSymptom
Information Bar 
						

							84
•Click Internet Options on the Tools menu of Internet
Explorer, and then click the [Security] tab. Then, click
the [Custom Level…] button to open the Security
Setting window. Under Miscellaneous, select
Enable for Allow script-initiated windows without
size or position constraints. Click the [OK] button.
The Warning window will be displayed. Click the
[Yes] button.
Solutions
–
An unnecessary status bar
or scroll bar is displayed on
the pop-up window.
Reference
pagesSymptom 
						

							Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be
mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be
accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer
upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human
health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority
for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
For U.S., Canadian and Puerto Rican fields:
Panasonic System Solutions Company, Unit Company of Panasonic Corporation of North America
Security Systems
www.panasonic.com/security
For customer support, call 1.877.733.3689
Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094
Zone Office
Eastern: Three Panasonic Way, Secaucus, New Jersey 07094
Central: 1707 N. Randal Road, Elgin, IL 60123
Southern: 1225 Northbrook Parkway, Suwanee, GA 30024
Western: 6550 Katella Ave., Cypress, CA 90630
Panasonic Canada Inc.5770 Ambler Drive,Mississauga, 
Ontario, L4W 2T3 Canada (905)624-5010
http://www.panasonic.ca
Panasonic Sales CompanyDivision of Panasonic Puerto Rico Inc.
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina
P.R. 00985(809)750-4300
© 2006 Matsushita Electric Industrial Co., Ltd. All Rights Reserved. N0906-5047      V8QB6471FN Printed in Japan
For European and other fields:
Matsushita Electric Industrial Co., Ltd.
Osaka, Japan
http://panasonic.net/