Panasonic Network Disk Recorder Wj Nd200 Setup Instructions

							Perform the settings of the registered cameras independently
51
Screenshot 1
Click the [Camera] button in the Setup panel and then
click the NW Camera Setup tab. The NW Camera
Setup page will be displayed.
Step 1
The following settings of the registered cameras will be
displayed.
CAM
It is possible to rearrange the order of the cameras.
When it is necessary to rearrange the displayed order of
the cameras after registering the detected cameras
using the [Search] button of Camera Search, select a
number of the camera to rearrange the order.
Click the [SET] button after completing the camera
order arrangement.
Important:
When the order of the cameras is rearranged, the
order of the cameras (CAM) for the following setup
items will automatically be rearranged. 
•Emergency REC – Emergency REC
•Schedule – Program Setup
•Maintenance – Network Information
Thumbnail
Thumbnail image from each camera will be displayed.
Note:
When failed to connect to the camera, the reason
why the connection failed will be displayed such as
the following.
CONNECT ERROR:Communication with the cam-
era cannot be established
ATTEST ERROR:User authentication of the cam-
era failed
DNS ERROR:DNS server cannot resolve the cam-
era address
CAMERA ERROR:Illegal response from the cam-
era
PROXY (CONNECT) ERROR:Cannot connect to
the proxy server
PROXY (DNS) ERROR:Cannot resolve the proxy
server address
PROXY (CAMERA) ERROR:Illegal response from
the proxy server
Information
Manufacturer, model/ compression method, address,
group title and camera title will be displayed.
Step 2
Click the [SETUP] button of the camera whose settings
are to be edited.
Note:
When a registered camera is disconnected, the
message CONNECT ERROR will be displayed in
the thumbnail image. When the disconnected cam-
era is not supposed to be connected again, select 
-- for MODEL/COMPRESSION of the setup
menu (Camera – NW Camera Setup – MODEL/
COMPRESSION) for the disconnected camera. 
						

							Settings of the title of the camera group [Group Setup]
Set the title of the camera group.
Screenshot 1
Click the [Camera] button in the Setup panel and then
click the Group Setup tab. The Group Setup page
will be displayed.
Step 1
Enter the title of the camera group. Enter up to 16
alphanumeric characters except the following: ! $ %  <
= > @ [  ] ^ _ ` { | } ~
Available characters are the same as for the camera
title.
Step 2
Click the [SET] button after completing the settings.
52
Screenshot 2
The Network Camera Registration window of the
selected camera will be displayed.
Step 3
The same setup items displayed on the Network
Camera Registration (list) window will be displayed.
Edit the settings for each item. Refer to page 50 for fur-
ther information about each setup item.
Step 4
Click the [SET] button after completing the settings. 
						

							53
Settings of the sequential display of images from cameras [Sequence Setup]
Perform the settings for the sequential display of live images.
Screenshot 1
Click the [Camera] button in the Setup panel and then
click the Sequence Setup tab. The Sequence Setup
page will be displayed.
Step 1
Edit the settings for each item.
Refer to the following for further information about the
settings for each item.
Step 2
Click the [SET] button after completing the settings.
[The Method of Sequence]
Select SPOT (single screen) or 4 Screens for The
Method of Sequence.
Default:SPOT
[SPOT Live Sequence]/[4 Screens Sequence]
When the [SETUP] button for the selected method is
clicked the following window will be displayed. Perform
the settings on this window. Click the [SET] button after
completing the settings, and close the window by click-
ing the [×] button at the top right of the window.
Note:
When the image compression method of the camera
selected for a camera channel is MPEG-4, the
respective sequence step will be skipped.
[CAM]
Select a camera whose images are to be displayed at
each step from the following.
- -:Skips the selected step.
CAM1 - 16 (when SPOT is selected):Switches
images from the selected camera channel on a sin-
gle screen (SPOT), starting from STEP1.
4A - 4D (when 4 Screens is selected):Switches
images of the preset camera groups (4A - 4D) of 4
channels in sequence on a 4-Screen, starting from
STEP1.
Setup items 
						

							54
Camera groups can be set on the Monitor Display
page (System – Basic Setup – Monitor Display
(page 30).
[PRESET]
Enter the preset position to where the camera is to be
moved at each step. (Only for SPOT Live Sequence)
Enter 1 – 256 for PRESET.
When no number is entered (blank), the camera will not
move at the respective step.
[DWELL]
Select a dwell time to go to the next sequential step
from the following.
2 s/3 s/5 s/10 s/20 s 
						

							55
Settings relating to network [Comm]
Perform the settings for a network connection such as settings of the IP address and gateway address.
Basic settings for a network [Basic Setup]
Basic network settings can be configured with this menu.
Screenshot 1
Click the [Comm] button in the Setup panel and then
click the Basic Setup tab. The Basic Setup page will
be displayed.
Step 1
Perform the settings for each item.
Refer to the following for further information about the
settings for each item.
Step 2
Click the [SET] button after completing the settings.
NW Link down detection
Select ON or OFF to enable or disable the network
line disconnection detection for the network port on the
rear of the unit.
ON:Detects if the disconnection of the network line
connected to the network port occurs.
OFF:Does not detect the network line disconnection.
NW Bandwidth Control
Select a rate for transmission from the following.
Unlimited/32 kbps/64 kbps/128 kbps/256 kbps/
512 kbps/1 024 kbps/2 Mbps/5 Mbps/10 Mbps
Important:
The bandwidth will not be controlled when live
images are transmitted in MPEG-4 format.
HTTP Port Number
Specify the HTTP port number to be used to send
images from the unit. A number from 1 - 65535 is avail-
able.It is unnecessary to change it for normal use.
Notes:
•Depending on the network settings of the LAN or
Internet service provider, network communication
may not be established if the http port number has
been changed. In this case, refer to the administra-
tor of the network.
•The following port numbers and the port numbers
used for the FTP port and for the site alarm setting
are unavailable for the HTTP port number.
20, 21, 23, 25, 42, 53, 67, 68, 69, 79, 105, 110, 123,
161, 162, 546, 547, 995, 10001, 10002, 10003,
10004, 10005, 10006, 10007
Setup items 
						

							56
FTP Port Number
Specify the FTP port number to be used.
Note:
The following port numbers and the port numbers
used for the HTTP port and for the site alarm setting
are unavailable for the FTP port number.
20, 23, 25, 42, 53, 67, 68, 69, 79, 80, 105, 110, 123,
161, 162, 546, 547, 995, 10001, 10002, 10003,
10004, 10005, 10006, 10007
Port Setup
Perform the settings for the following items for each
port.
[DHCP]
Select ON or OFF to determine whether or not to use
the DHCP server. Select ON to obtain an IP address,
a subnet mask and a gateway from the DHCP server.
Set to OFF when entering the addresses above manu-
ally.
ON:Uses the DHCP server.
OFF:Does not use the DHCP server.
[IP Address]
When OFF is selected for DHCP, enter an IP
address according to the network configuration. For this
unit, enter 4 units from the decimal numbers (0-255).
[Subnet Mask]
Enter a subnet mask according to the network configu-
ration when OFF is selected for DHCP.
[Gateway]
Enter the IP address of the gateway according to the
network environment when OFF is selected for
DHCP.
[Line Speed]
The following are available for Line Speed.
AUTO:Line speed will be applied automatically.
10-HALF:10 Mbps semi duplex
10-FULL:10 Mbps full duplex
100-HALF:100 Mbps semi duplex
100-FULL:100 Mbps full duplex
Note:
When the setup menu is closed after changing the
line speed, the unit will automatically restart.
Important:
A different subnet should be set for each port.
DNS Setup
Select MANUAL or AUTO to enable IP address
searching by the host name using the DNS. Select
OFF when not using the DNS.
Selecting AUTO is available only when ON is select-
ed for DHCP (using the DHCP server).
Selecting MANUAL is available regardless of the set-
ting for DHCP (with or without using the DHCP serv-
er).
When MANUAL is selected for the DNS, enter the
DNS server addresses in Primary and Secondary.
Enter 4 units from the decimal numbers (0-254).
Domain Name
Enter the domain name of this unit.Enter up to 255
alphanumeric characters including hyphens (-) and peri-
ods (.).
Note:
The first character of the domain name should be an
alphabetical character. 
						

							57
Basic network settings relating to DDNS [DDNS Setup]
Perform the basic settings of network DDNS.
Screenshot 1
Click the [Comm] button in the Setup panel and then
click the DDNS Setup tab. The DDNS Setup page
will be displayed.
Step 1
Perform the following setup items.
DDNS
Select ON or OFF to determine whether or not to use
the DDNS (Dynamic Domain Name Server).
When ON is selected, perform the following settings.
Default:OFF
User Name
Enter a user name registered in the DDNS.
Enter up to 32 characters using alphanumeric charac-
ters and the following marks.
User Password
Enter a password respective to the entered user name.
Enter up to 32 characters using alphanumeric charac-
ters and the following marks.
Note:
The following alphanumeric characters and marks
can be entered.
A B C D E F G H I J K L M N O P Q R S T U V W X
Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z 0 1
2 3 4 5 6 7 8 9 !  # $ %  ( ) * + , - . /: ; < = > ? @ [  ]
^ _ ` { | } ~
Access Interval
Select an interval to update the DNS from the following.
10 min/30 min/1 h/6 h/24 h
Default:1 h
Host Name
Enter a host name registered in the DDNS. Enter up to
255 alphanumeric characters including hyphens (-) and
periods (.).
Step 2
Click the [SET] button after completing the settings. 
						

							58
Basic settings relating to the proxy server [Proxy Setup]
Basic network proxy settings can be performed with this menu.
Screenshot 1
Click the [Comm] button in the Setup panel and then
click the Proxy Setup tab. The Proxy Setup page will
be displayed.
Step 1
Perform the following setup items.
Proxy Setup Use
Select ON or OFF to determine whether or not to use
the proxy server.
When ON is selected, perform the following settings.
Server Address
Enter a proxy server address. Enter up to 255 alphanu-
meric characters including hyphens (-) and periods (.).
Port Number
Enter a port number of a proxy server.
Exceptions
Perform the settings for cameras who does not use the
proxy server.
Enter the set address of the network camera. Enter up
to 128 alphanumeric characters including asterisks (*),
semicolons (;) and periods (.).
Notes:
•To exclude two cameras or more, use a semicolon
(;) to divide the addresses.
•Entering * validates all numbers.
Step 2
Click the [SET] button after completing the settings. 
						

							59
Settings for SNMP network [SNMP Setup]
Perform the settings for the SNMP. Perform the settings for the status check of the unit, etc. by connecting the
SNMP manager.
Screenshot 1
Click the [Comm] button in the Setup panel and then
click the SNMP Setup tab. The SNMP Setup page
will be displayed.
Step 1
Perform the following setup items.
COMMUNITY
Enter a name used for SNMP authentication in alphanu-
meric characters. Enter up to 32 characters using
alphanumeric characters and the following marks.
CONTACT
Enter the mail address of an administrator of this unit.
Enter up to 255 characters using alphanumeric charac-
ters and the following marks.
SYSTEM NAME
Enter a system name in alphanumeric characters to
manage this unit by the SNMP system, for example,
No1. Enter up to 255 characters using alphanumeric
characters and the following marks.
LOCATION
Enter a location name (location where this unit is
installed) in alphanumeric characters, for example, 2F.
Enter up to 255 characters using alphanumeric charac-
ters and the following marks.
Step 2
Click the [SET] button after completing the settings.
Note:
The following alphanumeric characters and marks
can be entered.
A B C D E F G H I J K L M N O P Q R S T U V W X
Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z 0 1
2 3 4 5 6 7 8 9 !  # $ %  ( ) * + , - . /: ; < = > ? @ [  ]
^ _ ` { | } ~ 
						

							60
Settings for the time adjustment of a network [NTP Setup]
Screenshot 1
Click the [Comm] button in the Setup panel and then
click the NTP Setup tab. The NTP Setup page will be
displayed.
Step 1
Perform the following setup items.
Time Adjustment
Select ON or OFF to determine whether or not to
adjust the time according to the NTP server.
Default:OFF
NTP Server Address
Enter the NTP server address when adjusting the time
using the NTP server. Enter up to 255 alphanumeric
characters including hyphens (-) and periods (.).
Refresh Interval
Select an interval of time inquiry to the NTP server from
the following.
1 h/2 h/6 h/12 h/24 h
Default:1 h
Step 2
Click the [SET] button after completing the settings.
Notes:
•The clock will be adjusted using the NTP server
when the clock of the unit becomes inaccurate
beyond ±5 seconds.
•The clock will not be adjusted when event recording
is being performed on any camera channel or when
emergency recording is being performed.
About the NTP server function
•This unit can be used as the NTP server for the con-
nected cameras. Set 123 for the port number on
the camera. Refer to the operating instructions of the
camera for how to perform the settings of the cam-
era.
•Time adjustment using the NTP server is unavail-
able for cameras with different subnet.