Panasonic Network Disk Recorder Wj Nd200 Setup Instructions

							21
[Zoom] box
Zooming can be adjusted by clicking the 
[WIDE] button or the  [TELE] button.
[Focus] box
Focusing can be adjusted by clicking the 
[NEAR] button or the  [FAR] button.
The auto focus function can be performed by clicking
the [AUTO] button.
[Auto mode] box
This box allows users to select the auto mode function
and operate the camera.
Click the  button to select the auto mode function
(Auto Track, Auto Pan, Preset Sequence, Sort, or
Patrol) of the camera, and click the  [START] but-
ton.
Click the  [STOP] button to stop the auto mode
function.
Control pad/buttons
Clicking the buttons around the control pad can move
(pan/tilt) a camera in the clicked direction. Clicking
inside the control pad also can adjust the vertical/hori-
zontal position (pan/tilt) of the displayed image.
Panning/tilting speed will be faster if a clicked point gets
farther from the center point of the control pad.[Brightness] box
The brightness can be adjusted by clicking the 
[–] button or the  [+] button. It is possible to reset
the set brightness by clicking the  [RESET] but-
ton.
[Preset] box
This box allows users to register the current camera
direction on a specified preset position. Aim the camera
at a direction to be registered, click the  button to
select a preset number (1-256), and click the 
[Program] button.
Move the camera to the preset position registered in
advance. Click the  button to select the preset number
and click the  [GO] button.
[CAM] Tab
Control pad/buttons 
						

							22
Setup Menu
Performing each setting item on the setup menu should be completed in advance to operate this unit.
The setup menu operations are performed from the Setup panel.
Setup menu chart
Setup items Description Page
Quick
Setup Perform the minimum required settings to operate this unit.
System
Basic Setup Perform the settings for the basic operations of this unit.
Time & Date Perform the settings for the current time and for displaying the
time and date.
Emergency recording
Emergency REC Perform the settings for emergency recording such as the record-
ing time and recording rate.
Event Action
Basic Setup Perform the basic settings for an event action.
Terminal Setup Set event actions to be performed at a terminal alarm occur-
rence.
Site Alarm Setup Set event actions to be performed at a site alarm occurrence.
Schedule
Time Table Create timetables for each day of the week, and assign a pro-
gram to each timetable.
Program Create recording programs on this menu. Up to 4 programs can
be created. Perform the settings for recording actions such as
the recording rate for each camera channel.
Special Days Assign timetables to special days aside from other days of the
week.
Camera
NW Camera Setup Perform the network camera settings such as the camera
address and the port number.
Group Setup Set the group title of the camera.
Sequence Setup Perform the settings for the sequential display of live images.27
30
31
34
36
37
38
44
39
46
47
52
53 
						

							23
Setup items Description Page
Comm
Basic Setup Perform the settings for a network. Settings for a network con-
nection such as settings of the IP address and gateway address
can be performed.
DDNS Setup Perform the basic settings of network DDNS.
Determine to enable or disable DDNS, or perform the settings of
the user IDs.
Proxy Setup Perform the basic network proxy settings.
Determine whether or not to use the proxy server, and perform
the settings such as the server address settings, etc.
SNMP Setup Perform the settings for the SNMP. By connecting to the SNMP
manager, the status check of the unit can be checked.
NTP Setup Perform the settings when adjustment of the time is required to
be set with the NTP server such as when setting the NTP server
address.
FTP Setup Perform the settings for the FTP server. Settings for transmitting
images from a camera connected to this unit to a designated
FTP server periodically can be performed with the FTP Setup
menu.
Mail Setup Perform the settings to send e-mails to addresses registered in
advance at an event or error occurrence.
Panasonic Alarm protocol It is possible to send a message to addresses registered in
advance using Panasonic Alarm Protocol when an event or a
problem occurs.
User Mng.
Basic Setup Determine whether to enable or disable the user authentication
and the host authentication.
Administrator Setup Edit information of the registered administrators such as the
administrator name, password, the default screen, etc.
User Setup Register users who can operate the unit and edit/delete the reg-
istered user information.
User name, password and operational level can be set.
Host Setup Register hosts (PCs) that can access the unit via a network and
edit/delete the registered host information.
Operational levels and IP addresses of PCs can be set.
User Level Functions operable in each user level can be set.55
57
58
59
60
61
63
64
65
66
67
68
70 
						

							24
Setup items Description Page
Maintenance
Product Information Versions of the software, hardware (this unit), MAC address, the
internal temperature and the number of times the USE button is
pressed will be displayed.
Disk Information Hard disk information such as available capacity of the built-in
hard disk will be displayed.
Network Information Network information such as IP addresses of the connected cam-
eras and network line speed of the WJ-ND200 will be displayed.
Disk Setup Perform the settings relating to the remaining disk size and the
settings relating to image data.
Data recorded on the HDD can be deleted and actions to be
taken when the remaining disk size runs out can be configured.
Save/Load Contents of settings for this unit will be saved/loaded or initial-
ized.
ConfigEnable/disable setting of the FORMAT button inside the front
cover can be set, and the hard disk drives can be formatted.72
73
73
74
75
77 
						

							25
Basic operation with the setup menu
Screenshot 1
Start operation from the top page.
Step 1
Click the [Setup] button.
Screenshot 2
The Setup panel will be displayed.
Step 2
Click the desired button relating to the settings to be
configured.
Setup panel 
						

							26
Screenshot 3
The setup menu respective to the clicked button on the
Setup panel will be displayed.
Step 3
Click the tab relating to the settings to be configured.
Screenshot 4
The setup menu corresponding to the selected tab will
be displayed in the image display area.
Step 4
Perform the settings for each item.
Click the [SET] button after completing the settings.
→The settings will be applied.
When moving to other setup menu without clicking
the [SET] button, the edited settings will not be
applied.
Important:
•When the settings are applied, all users except for
the user who edited and applied the settings will be
forcibly logged out.
•When any setting of User Mng. is changed, all
login users will be forcibly logged out.
•Recording will not be performed for around 4 sec-
onds just after saving the settings.
Tabs 
						

							27
Perform the minimum required settings [Quick]
Perform the minimum required settings to operate this unit.
Before perform the settings on each setup menu, check the settings on the Quick menu first.
Screenshot 1
Click the [Quick] button to display the Quick menu.
Step 1
Perform the settings for each item.
Refer to the following for further information about the
settings for each item.
Step 2
Click the [SET] button after completing the settings.
Note:
When there are two or more [SET] buttons on the
page, click the respective button to the edited setting
item.

When completing the setting items in field A, click
the [SET] button below field A (A-1). The edited set-
ting items in field A will not be applied unless the
[SET] button below field A (A-1) is clicked.
In the same manner above, click the [SET] button
below field B (B-1) when completing the setting
items in field B.
A
A-1
B
B-1 
						

							28
Setup items
Language
Select the display language for the web browser from
the following.
JAPANESE/ENGLISH
Time & Date
Adjust the current time and date.
Select numbers for year, month, day, hour and minute,
and click the [SET] button.
Important:
•Recording will not be performed for around 4 sec-
onds just after applying the time and date settings.
•Live images will turn to black screen and recording
will not be performed for around 4 seconds just after
applying the time and date settings even by shifting
to/from summertime (daylight savings).
Port Setup
Perform the settings for the following items for each
port.
[DHCP]
Select ON or OFF to determine whether or not to use
the DHCP server. Select ON to obtain an IP address,
a subnet mask and a gateway from the DHCP server.
Set to OFF when entering the addresses above manu-
ally.
ON: Uses the DHCP server.
OFF:Does not use the DHCP server.
Important:
A different subnet should be set for each port.
[IP Address]
When OFF is selected for DHCP, enter an IP
address. For this unit, enter 4 units from the decimal
numbers (0-255) according to the network configuration.
[Subnet Mask]
Enter a subnet mask according to the network configu-
ration when OFF is selected for DHCP.
[Gateway]
Enter the IP address of the gateway according to the
network environment when OFF is selected for
DHCP.[Line Speed]
The following are available for Line Speed.
AUTO:Line speed will be applied automatically.
10-HALF:10 Mbps semi duplex
10-FULL:10 Mbps full duplex
100-HALF:100 Mbps semi duplex
100-FULL:100 Mbps full duplex
Note:
When the setup menu is closed after changing the
line speed, the unit will automatically restart.
Camera Auto Registration
The unit will search cameras and register the detected
cameras automatically. Determine how to register IP
addresses of cameras.
Register the IP address automatically given by this
unit to a detected camera:When a camera is
detected, the unit will give an IP address to the
detected camera and register it.
Register the IP address set with a detected camera:
When a camera is detected, the unit will register the
IP address of the detected camera.
Notes:
•When Camera Auto Registration is carried out, the
other login users will be forcibly logged out.
•Recordings currently being carried out on this unit
will stop in the process of Camera Auto
Registration.
•Camera Auto Registration is unavailable for cam-
eras on a different subnet.
•Depending on the camera model, the unit cannot
detect them for their security when 20 minutes have
passed after the power of the camera is turned on.
Refer to the operating instructions of the camera for
further information.
•The image compression method of the registered
camera will automatically be set to JPEG or M-
JPEG.
•When selecting Register the IP address automati-
cally given by this unit to a detected camera, the
unit will automatically find an unused IP address and
set it to the detected camera. However, depending
on the network environment, the set IP address may
be already used for the other network device such
as when using the firewall function of Windows
®. 
						

							29
In this case, check the IP address setting and regis-
ter the other IP address for the camera manually.
•When Register the IP address set with a detected
camera is selected and the DHCP setting of the
detected camera is ON, the unit will automatically
set the DHCP setting of the camera to OFF and
give a new IP address to the camera.
•Register the IP address automatically given by this
unit to a detected camera is available only when
OFF is set for the DHCP settings of the unit.
•Before selecting Register the IP address automati-
cally given by this unit to a detected camera, set the
subnet of the network port to 255.255.255.0.
•The following cameras are compatible with the
Camera Auto Registration function.
WV-NM100/WV-NS32x/WV-NW47x/WV-NP244
series/WV-NP1000 series/WV-NS202/WV-NF284/
WJ-NT304/WV-NW484
•When the IP address is registered to the camera,
the HTTP port of the camera will automatically set to
80, and the same subnet and the gateway of the
unit will be set to the camera.
•When the same IP address is used for the other
camera, the IP address and the MAC address will be
displayed in red on the Camera Search Result win-
dow (page 48). Make sure that the same IP
address is used for two cameras or more.
Important:
When selecting Register the IP address automati-
cally given by this unit to a detected camera, the
unit will give IP addresses to all of the detected cam-
eras. Before selecting Register the IP address auto-
matically given by this unit to a detected camera,
make sure that there is no camera that is to be used
with the unique IP address.
Program Setup
The program setting window will be displayed when the
[View] button is clicked after selecting a program from
the pull-down.
Refer to page 40 for further information about the
Program Setup window. 
						

							30
Perform the settings for the system [System]
Perform the settings for the system of this unit.
Perform the basic settings for the system [Basic Setup]
Perform the settings for the basic operations of this unit.
Screenshot 1
Click the [System] button in the Setup panel then click
the Basic Setup tab. The Basic Setup page will be
displayed.
Step 1
Perform the settings for each item.
Refer to the following for further information about the
settings for each item.
Step 2
Click the [SET] button after completing the settings.
Setup items
Recording
Select ON or OFF to record or not record.
OFF:No recording will be performed.
ON: Recording will be performed.
Default:ON
Language
Select the display language for the web browser from
the following.
JAPANESE/ENGLISH
Default:ENGLISH
Monitor Display
It is possible to allocate camera channels to each sec-
tion of a 4-Screen when displaying images on a 4-
Screen. It is necessary to perform the settings of the
camera group for the sequential display on a 4-Screen
(4A - 4D).The following window will be displayed when the
[SETUP] button is clicked. It is possible to allocate 4
camera channels to each section (4A - 4D). Images
from the selected camera channel will be displayed in
the respective section of a 4-Screen in the image dis-
play area.
Click the [SET] button after completing the settings, and
close the window by clicking the [×] button at the top
right of the window.