Panasonic Network Disk Recorder Wj Nd200 Setup Instructions

							11
Equipped security functions
qAccess restrictions by the host authentication and the user authentication
It is possible to restrict users from accessing this unit by setting the host authentication and/or the user authenti-
cation to on. (page 65)
wAccess restrictions by changing the HTTP port
It is possible to prevent illegal access such as port scanning, etc. by changing the HTTP port number. 
(page 55)
For enhanced security
Divide the subnet using a router to enhance the network security by double authentications of IP addresses using
this unit and a router. When required to connect this unit with a network without enhanced security, connect the unit
after the network security is enhanced, such as by installing a VPN (Virtual Private Network) device, etc.
Important:
The settings of the unit will be different depending on the settings of the LAN or the Internet service provider to
which the unit is to be connected. Refer to an administrator of each network for further information about the
respective network.
[Connection example]
Installing a firewall to use the packet filtering and the protocol filtering functions can better enhance the network
security.
[Connection example]
About the Network Security of This Unit
WAN*
Router Router
IP address: 192.168.1.100
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1IP address: 192.168.0.250
Subnet mask: 255.255.255.0
Default gateway: 192.168.0.1 IP address: 192.168.0.1
Subnet mask: 255.255.255.0
IBM PC/AT compatible IP address: 192.168.1.1
Subnet mask: 255.255.255.0
This unit
* Wide Area Network
ON
OFF
POWER ALARMALARM/CONTROLSIGNAL GND10/100BASE-TAC IN
WAN*
Switching hub Firewall
Router Router
IP address: 192.168.1.100
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1IP address: 192.168.0.1
Subnet mask: 255.255.255.0 IP address: 192.168.1.1
Subnet mask: 255.255.255.0
IP address: 192.168.0.250
Subnet mask: 255.255.255.0
Default gateway: 192.168.0.1
IBM PC/AT compatible* Wide Area Network
This unit
ON
OFF
POWER ALARMALARM/CONTROLSIGNAL GND10/100BASE-TAC IN 
						

							12
Display the Operation Window
To display the operation window to operate the unit from the web browser installed on the PC, proceed as follows.
Screenshot 1
Start just after the PC is started up.
Step 1
After the browser starts, enter the IP address set to this
unit in the address box, and press the enter key.
Important:
•Refer to a system administrator for the IP address.
•It is impossible to access this unit from a PC without
a registered IP address when ON is selected for
Host Authentication on the Basic Setup of User
Mng. menu.
Refer to a system administrator for further informa-
tion.
•Do not attach 0 before the numbers when entering
IP address.
Example
Correct: 192.168.0.50
Wrong: 192.168.0.050
•If a message is displayed on the information bar,
see page 83.
Screenshot 2
The user authentication window will be displayed.
This window will not be displayed when OFF is select-
ed for User Authentication on the Basic Setup of
User Mng. menu.
Step 2
Enter the user ID and password registered on this unit.
Important:
•Refer to a system administrator for the set user
name and password.
Refer to page 67 for the descriptions of how to regis-
ter users.
•The default administrator name and password are
as follows.
USER ID: ADMIN
Password: 12345
•To enhance the security, change the password for
an administrator before running the unit. It is recom-
mended to change the password for the administra-
tor periodically. Refer to page 66 for descriptions of
how to change the password. 
						

							13
Screenshot 3
The top page will be displayed.
Step 3
Click the buttons or the tabs for operations.
Important:
If a message is displayed on the information bar,
see page 83.
Notes:
•When the top page is displayed for the first time, the
install wizard of the ActiveX control required to dis-
play images from the camera will be displayed.
Follow the instructions of the wizard.
•When the install wizard is displayed again even after
completing the installation of the ActiveX, restart the
PC.
Important:
When the unit is being operated without changing
the default administrator name and password, the
pop-up window saying that it is recommended to
change the password will be displayed. 
						

							14
About the Operation Window
[Control] button [Cam Select] button
[Setup] buttonStatus display areaCurrent time display area
Playback image
display area
Time and date of the
displayed image
Playback point
operation area
[HDD] tab
[CAM] tab
Camera title
Top page
[Control] button (page 15)
Clicking this button displays the Control panel that is
used for performing operations such as searching for
recorded pictures on the HDD and playing recorded pic-
tures. From the Control panel, you can also perform
the functions of the camera picture switcher such as
changing the display of camera live pictures to quad or
sequence display. Search result and log information
also will be displayed on the Control panel.
[Cam Select] button (page 16)
Clicking this button displays the Cam Select panel that
is used for the switcher function such as switching cam-
era channels.
[Setup] button (page 17)
Clicking this button displays the Setup panel that is
used for the setup operations.
Status display area (page18)
Current status such as playback status or recording sta-
tus will be displayed.
Current time display area
Current time will be displayed.Playback image display area
Recorded images and live images will be displayed. The
setup menu will be displayed while setting up.
The camera title is displayed at the top left of the picture
and the time at the top right. (Time and date when
images had been recorded will be displayed when dis-
playing recorded images.) Clicking the camera title dur-
ing quad display will display the clicked picture on a sin-
gle screen.
Playback point operations area (page 19)
It is possible to mark playback points or skip to the lat-
est recorded image.
[HDD] tab (page 19)
Operation for recorded images such as playback or
downloading (saving) recorded images can be per-
formed on this page.
[CAM] tab (page 21)
Perform the camera operations such as zooming, focus-
ing, auto functions, etc. on this panel. 
						

							15
[Control] button
When the [Control] button is clicked, the Control panel will be displayed.
[Multiscreen Select] box
Up to 4 camera images can be displayed simultaneous-
ly on a 4-Screen.
Each time the button is clicked, the camera picture is
changed to quad display according to the settings made
in the Monitor Display page (System – Basic Setup
– Monitor Display).Control panel[Sequence] box
Camera images to be displayed will be switched by
clicking this button. Camera images will be displayed
sequentially according to the settings performed in
advance.
The indicator on the button lights (green) during
sequence operation.
[EL-Zoom] box
Camera images will be displayed in the proportion of the
clicked zoom ratio button.
:1x :2x :4x
[Search] box
The recording event search window will be displayed by
clicking this button. Use this button to search the record-
ed images. (Refer to the operating instructions (PDF).)
Search results will be displayed in list form in the log
display area. (Refer to the operating instructions (PDF).)
[Log] box
[Error Log] button:The error logs of this unit
will be displayed. Logs will be displayed in list form
in the log display area.
[Access Log] button:The time when logged
in/out for this unit, the user ID, or the IP address will
be displayed. Logs will be displayed in list form in
the log display area.
[Event Log] button:The event logs (event
occurrence times and their details) will be displayed.
Logs will be displayed in list form in the log display
area.
[Network Log] button:The network error logs
will be displayed. Logs will be displayed in list form
in the log display area.
[Zoom In]:Enlarges the live camera image
and playback picture. 
						

							16
[Cam Select] button
When the [Cam Select] button is clicked, the Cam Select panel will be displayed.
[Multiscreen Select] box
Multiscreen button:
Up to 4 camera images can be displayed simultaneous-
ly on a 4-Screen.
Each time the button is clicked, the camera picture is
changed to quad display according to the settings made
in the Monitor Display page (System – Basic Setup
– Monitor Display).
[Sequence] box
Sequence button:
Camera images to be displayed will be switched by
clicking this button. Camera images will be displayed
sequentially according to the settings performed in
advance.
The indicator on the button lights (green) during
sequence operation.
[EL-Zoom] box
Camera images will be displayed in the proportion of the
clicked zoom ratio button.
:1x :2x :4x
[Camera Select] box
When the WJ-ND200 title is clicked, the group title of
the cameras will be displayed. Refer to page 52 for the
descriptions of how to perform the group settings.
When the group title is clicked, the cameras belong to
the group will be displayed in the tree form. When the
camera title is clicked, images from the selected camera
will be displayed on a single screen in the image display
area.
Group title
Camera title
Cam Select panel 
						

							17
[Setup] button
When the [Setup] button is clicked, the Setup panel will be displayed.
[Emergency REC] button
The setup menu for the emergency recording will be
displayed. Perform the settings for emergency record-
ing. Refer to page 34 for further information.
[Event] button
Displays the setting menu for event actions of each
event type (site alarm and terminal alarm). Refer to
page 36 for further information.
[Schedule] button
The menu for the settings of the recording schedule
(performs recording/event action by designating the
time and a day of the week) will be displayed.
Refer to page 39 for further information.
[Camera] button
This button is for performing camera network settings,
group settings and sequence operation settings. 
Refer to page 47 for further information.
[Comm] button
The setup menu for network settings of the WJ-ND200
will be displayed. Refer to page 55 for further informa-
tion.
[User Mng.] button
The setup menu for user and host authentication will be
displayed. Refer to page 65 for further information.
[Maintenance] button
The setup menu for the settings of the hard disk will be
displayed. Refer to page 72 for further information.
[Config] button
The setup menu for formatting of the hard disk will be
displayed. Refer to page 76 for further information.
[Help] button
The help window will be displayed.
[Quick] button
When this button is clicked, the setup menu that con-
tains the minimum required settings to operate this unit
will be displayed.
Refer to page 27 for further information.
[System] button
The setup menu that contains the required system set-
tings to activate this unit will be displayed. Refer to page
30 for further information.
Setup panel 
						

							18
Status display area
wer
q
qThe status of live/playback image will be
displayed.
[LIVE]:
Indicates that a live image is being displayed.
[Playback]:
Indicates that a playback image is being dis-
played.
[Reverse playback]:
Indicates that a reverse playback image is being
displayed.
[Fast playback]:
Indicates that a fast playback image is being dis-
played.
[Fast reverse playback]:
Indicates that a fast reverse playback image is
being displayed.
[Pause]:
Indicates that a paused image is being dis-
played.
[DL]:
Indicates that the playback images are currently
being downloaded.
[END]:
Indicates that download of the playback images
has ended.
–  [Step 1] – [Step 7]:
Indicates the playback speed.
Step1:Normal playback speed
Step2:Approx. 4x playback speed
Step3:Approx. 8x playback speed
Step4:Approx. 16x playback speed
Step5:Approx. 32x playback speed
Step6:Approx. 48x playback speed
Step7:Approx. 96x playback speed
[SEQ]:
Indicates that the sequence display is currently
being performed.
[HDD]:
Indicates that a HDD is currently being mounted
in the unit.[RECOVER]: 
Indicates that mirroring recovery is currently
being performed.
[FILTERING]:
Indicates that the recording event list is filtered.
Refer to the operating instructions (PDF) for fur-
ther information about filtering of the recording
event list.
wREC indicator
The status of recording will be displayed.
When lit red:Indicates that recording is being per-
formed.
When not lit:Indicates that recording is not being
performed.
eIndicates the following statuses:
[BUSY]:
Indicates that the camera is not operable
because a user with higher priority is currently
operating that camera.
[DELETE]:
Indicates that deletion of a recorded image is
being performed.
rIndicates information about events and errors.
Clicking this button will temporarily disable alarm
detection. (Refer to the operating instructions
(PDF).)
[ALARM SUSPEND]:
Clicking this button will temporarily disable alarm
detection (alarm suspension). (Refer to the operat-
ing instructions (PDF).)
[ALARM SUSPEND]:
This indication will be displayed while an alarm is
being suspended.
[ALM]:
Indicates an event occurrence. The alarm display
action will be canceled by clicking this button.
(Refer to the operating instructions (PDF).) 
						

							19
qIndicates the start time and the end time of a down-
load. (Refer to the operating instructions (PDF).)
[Start] button
Set the start time for the time and date of the
image to be downloaded.
[End] button
Set the end time for the time and date of the
image to be downloaded.w[GO TO DATE] button
Indicates the time and date of a marked point. Use
this button to designate the desired time and date of
a recorded image to be played. (Refer to the operat-
ing instructions (PDF).)
e[GO TO LAST] button
Skips to the latest recorded time of a recorded
image from the currently displayed camera channel
and plays it.
Playback point operation area
[HDD] tab
[REW] button
Fast reverse playback will be performed. Playback
speed for fast reverse playback will be changed in the
following order each time this button is clicked: 
Step2 (Approx. 4x) →Step3 (Approx. 8x) →
Step4 (Approx. 16x) →Step5 (Approx. 32x) →
Step6 (Approx. 48x) →Step7 (Approx. 96x)
[PREV RECORD] button
Skips to the previous recorded image and plays it.[REV PLAY] button
Reverse playback of a recorded image will be per-
formed.
[PLAY] button
Playback of a recorded image will be performed.
[NEXT RECORD] button
Skips to the next recorded image and plays it.
qwe
[ERR]:
Indicates an error occurrence. The error will be
reset by clicking this button. (Refer to the operat-
ing instructions (PDF).)
Note:
When CONTINUE is selected for Recording
Duration of Emergency REC, the emergency
recording currently being carried out can be stopped
by clicking the [ALM] button. When MANUAL is
selected for Recording Duration, the emergency
recording will not stop by clicking the [ALM] button. 
						

							20
[FF] button
Fast playback will be performed. Playback speed for
fast playback will be changed in the following order
each time this button is clicked: Step2 (Approx. 4x) →
Step3 (Approx. 8x) →Step4 (Approx. 16x) →
Step5 (Approx. 32x) →Step6 (Approx. 48x) →
Step7 (Approx. 96x)
[PREV IMAGE] button
The previous frame will be displayed when this button is
clicked during playback/pausing.
[PAUSE] button
Playback will be stopped when this button is clicked dur-
ing playback. Playback will be resumed when this but-
ton is clicked during pausing.
[STOP] button
Stops playback and displays a live image.
[NEXT IMAGE] button
The next frame will be displayed when this button is
clicked during playback/pausing.
[Download (TO PC)] box
Downloads the image currently playing to a PC.
[Download] button
Displays the download setting window for download-
ing images.
Date and time of the download start/end points will
be displayed in the playback position operations
area.
[VIEWER] button
Clicking this button will start downloading the viewer
software that can play downloaded images.
[TEXT] button
The attached text information will be displayed when
this button is clicked during pausing.
[REC] box
The recording button, the recording stop button and the
SD memory data obtain button will be displayed when
the  button is clicked.
The recording button, the recording stop button and the
SD memory data obtain button will be hidden when the
button is clicked.SD memory data obtain button
Obtains recorded images on the SD memory card
on the camera. The letters SD on this button will be
displayed in red when there are recorded images on
the SD memory card.
The letters SD on this button will be displayed in
blue when there is no recorded image on the SD
memory card. When this button is clicked while the
letters SD are displayed in blue, the unit will check
if there is any recorded image on the SD memory
card or not. When a recorded image is found, the
letters SD on the SD memory data obtain button
will turn red.
Recording button:Starts manual recording.
Recording stop button:Stops manual recording.
Important:
To display the recording button and the recording
stop button, hold down the  button until they are
displayed.
Note:
When played image is in MPEG-4 format, results
from operating the some buttons will be as follows.
[GO TO DATE] button:Playback sometimes may
start from a point several seconds after the des-
ignated time and date.
[REV PLAY] button:Some frames of recorded
images will not be displayed. Reverse playback
will be performed with the set refresh interval of
the camera.
[PLAY] button (during playback):When the
[PLAY] button is clicked during playback, images
will be skipped for several seconds. (Playback
will starts from a point several seconds after the
current point.)
[PREV IMAGE] button:Some frames of recorded
images will not be displayed. Reverse frame play
will be performed with the set refresh interval of
the camera.
[FF]/[REW] button:Some frames of recorded
images will not be displayed. Fast playback/fast
reverse playback will be performed with the set
refresh interval of the camera.
[Download] button (during playback):Download
may start from a point several seconds later than
the designated start time and may end at a point
several seconds after the designated end time
when downloading MPEG-4 images.