Panasonic Network Camera Wv Sw352 Wv Sw355 Installation Guide

31
z Mount the camera.
    
  q Connect each cable. (
☞ Page 26) Waterproof the connecting portion. (☞ Page 29)
  w Align the "OPEN" on the camera with the projection of the camera attachment.
  e Engage  the  camera  attachment  fixing  screws  on  the  rear  of  the  camera  in  the  camera 
mounting  holes  of  the  camera  attachment  and  rotate  the  camera  in  the  arrow  direction  to 
secure the camera attachment and camera. 
    Rotate the camera until a click is heard so that the...

32

 q  Attach the camera onto the camera attachment 
while  aligning  the  "OPEN"  mark  of  the  camera 
with the projection of the camera attachment. 
LOCKOPEN
Projection
LOCKOPEN
Important: 
	 •	 When	 mounting	the	camera	 body,	cables	 shall	
be  run  between  the  camera  attachment  and 
mount bracket as indicated by the arrows in the 
illustration.
  * Cable running as indicated by the arrows in the 
illustration is an example. Cable running shall be 
varied with installation environment....

33
 w  Engage  the  rear-side  screw  of  the  camera  with 
the  screw  hole  of  the  camera  attachment  and 
rotate  the  camera  in  the  direction  of  the  arrow 
to  secure  the  camera  to  the  camera  attach-
ment.
    Rotate  the  camera  until  a  click  is  heard  so  that 
the projection of the camera attachment will be 
set to the "LOCK" position.
  e  Connect  the  cables  on  the  side  of  the  mount 
bracket. (
☞ Page 26)
    Waterproof  the  connecting  portion.  (
☞  Page...

34
 t  Attach  the  base  cover  that  was  removed 
according the steps in page 21.
  y  Use  the  bit  for  tamperproof  screw  (accessory) 
to  tighten  the  fixing  screws  provided  on  both 
sides  of  the  base  cover.  (Recommended  tight-
ening torque: 0.78 N·m {0.58 lbf·ft})
x   Detach  the  enclosure  and  inner  dome  from  the 
main body by loosening the three fixing screws. 
    Loosen  the  three  fixing  screws  by  using  the  bit 
for tamperproof screw (accessory). 
    Detach  the...

35
c   Secure  the  camera  to  the  mount  bracket  with 
the camera fixing screw (red, 1 position).
    The  illustration  is  an  example  of  using  the 
mount bracket (accessory). 
Important: 
	 •	 Be	 sure	to	tighten	 the	camera	 fixing	screw.	
Failure to observe this may cause camera trou-
ble due to water leakage or camera falling. 
    (Recommended  tightening  torque:  0.78  N·m 
{0.58 lbf·ft})
Camera xing screw (red)
* The camera fixing screw  shall be securely tightened. 

36
z Adjust the camera angle.
When  determining  the  camera  angle,  repeat  fine  adjustments  by  gradually  moving  the  panning 
table, tilting table, and azimuth adjustment ring. 
Horizontal position (Panning)
Loosen  the  panning  lock  screw,  rotate  the  panning  table  to  adjust  the  pan  direction.  (Adjustable 
range: 340 °)
Panning  is  possible  within  the  range  of  180  °  (when  panning  clockwise)  and  160  °  (when  panning 
counterclockwise). 
After adjustment, tighten the...

37
   
Horizontal: 27.7 ° (TELE) to 100.8 ° (WIDE)
Vertical: 20.8 ° (TELE) to 73.8 ° (WIDE)
    After adjustment, tighten the tilting lock screws (x2) to fix the tilting table. 
    (Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
Note:
	 •	 When	 the	tilting	 table	is	turned	 to	the	 edge	 of	the	 adjustable	 range	(±75°),	 it	must	 be	noted	 that	
the shadow of the enclosure may be projected.
Image tilt adjustment
Rotate  the  azimuth  adjustment  ring  to  adjust  the  azimuth  angle  of  the...

38
x Adjust the angular field of view and the focus. 
    Adjust the angular field of view in accordance with the distance between the camera lens and a 
photographic  subject.  These  adjustments  shall  be  performed  together  with  the  camera  angle 
adjustment.
  q  Loosen the zoom lock knob and move the knob between TELE and WIDE to obtain the appro-
priate angle of view. 
Note:
	 •	 The	 focus	may	not	be	adjusted	 appropriately	 when	the	zoom	 ring	is	positioned	 at	the	 "W"	 (or...

39
Important: 
	 •	 Do	not	move	the	focus	ring.
	 •	 Defocus	 may	be	caused	 by	the	 reinstalled	 enclosure.	 In	this	 case,	 perform	 the	auto	 focus	 func-
tion from the setup menu. 
Note:
	 •	 If	 the	zoom	 ring	is	fully	 rotated	 in	the	 "W"	 direction,	 the	periphery	 may	become	 dark.	In	such	 a	
case, rotate the zoom ring in the "T" direction for readjustment. 
	 •	 If	 the	zoom	 lock	knob	 is	slightly	 tightened	 before	the	zoom	 ring	is	moved,	 the	ring	 will	become	
stable to...

40
c Mount the inner dome that was removed according the steps in page 34 in the reverse proce-
dure. Check to see that the tilting lock screws of the camera are properly engaged in the holes 
of the inner dome.
    Tighten  the  screws  that  have  been  loosened  in  step  x  on  page  34  using  the  bit  for  tamper-
proof screw (accessory). 
Important: 
	 •	 Securely	 tighten	all	the	 fixing	 screws	 (x3)	of	enclosure.	 Otherwise,	 water	exposure	 may	cause	
damage  or  malfunction  of  camera,  or...