Panasonic Network Camera Wv Sw352 Wv Sw355 Installation Guide
Have a look at the manual Panasonic Network Camera Wv Sw352 Wv Sw355 Installation Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
31
z Mount the camera.
q Connect each cable. (
☞ Page 26) Waterproof the connecting portion. (☞ Page 29)
w Align the "OPEN" on the camera with the projection of the camera attachment.
e Engage the camera attachment fixing screws on the rear of the camera in the camera
mounting holes of the camera attachment and rotate the camera in the arrow direction to
secure the camera attachment and camera.
Rotate the camera until a click is heard so that the projection of the camera attachment will
be set to the "LOCK" position.
Installation
FRONTTOP
OPEN
LOCK
Camera attachment xing screw Projection
Camera mounting hole
32
q Attach the camera onto the camera attachment
while aligning the "OPEN" mark of the camera
with the projection of the camera attachment.
LOCKOPEN
Projection
LOCKOPEN
Important:
• When mounting the camera body, cables shall
be run between the camera attachment and
mount bracket as indicated by the arrows in the
illustration.
* Cable running as indicated by the arrows in the
illustration is an example. Cable running shall be
varied with installation environment.
33
w Engage the rear-side screw of the camera with
the screw hole of the camera attachment and
rotate the camera in the direction of the arrow
to secure the camera to the camera attach-
ment.
Rotate the camera until a click is heard so that
the projection of the camera attachment will be
set to the "LOCK" position.
e Connect the cables on the side of the mount
bracket. (
☞ Page 26)
Waterproof the connecting portion. (
☞ Page
29)
Note:
• Disconnect the 12 V power source and PoE
power source to prevent power from being sup-
plied during mounting work.
r Accommodate the connected cables inside the
cable guide of the camera mount bracket.
Important:
• To prevent the cables from being caught when
the base cover is attached, keep the cables
inside the cable guide.
LOCKOPEN
LOCKOPEN
Projection
Make cable connection and
waterproof the connected section.
Cable
guide
Cable
guide
Connected
cable
34
t Attach the base cover that was removed
according the steps in page 21.
y Use the bit for tamperproof screw (accessory)
to tighten the fixing screws provided on both
sides of the base cover. (Recommended tight-
ening torque: 0.78 N·m {0.58 lbf·ft})
x Detach the enclosure and inner dome from the
main body by loosening the three fixing screws.
Loosen the three fixing screws by using the bit
for tamperproof screw (accessory).
Detach the inner dome while pushing toward
the directions as indicated by the arrows in the
illustration.
Important:
• Do not hold the inner dome when carrying the
camera. Otherwise, the camera part may fall
and it may damage the camera.
• Remove the cover film from the transparent part
of the dome cover after the installation is com-
plete. Do not touch the dome cover by hand
directly after removing the cover film.
Base cover
Base cover
xing screw
AF/EXTRA OPTICAL ZOOM
LINK ACT
Push.
Push.
35
c Secure the camera to the mount bracket with
the camera fixing screw (red, 1 position).
The illustration is an example of using the
mount bracket (accessory).
Important:
• Be sure to tighten the camera fixing screw.
Failure to observe this may cause camera trou-
ble due to water leakage or camera falling.
(Recommended tightening torque: 0.78 N·m
{0.58 lbf·ft})
Camera xing screw (red)
* The camera fixing screw shall be securely tightened.
36
z Adjust the camera angle.
When determining the camera angle, repeat fine adjustments by gradually moving the panning
table, tilting table, and azimuth adjustment ring.
Horizontal position (Panning)
Loosen the panning lock screw, rotate the panning table to adjust the pan direction. (Adjustable
range: 340 °)
Panning is possible within the range of 180 ° (when panning clockwise) and 160 ° (when panning
counterclockwise).
After adjustment, tighten the panning lock screw to fix the panning table.
(Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
Vertical position (Tilting)
Loosen the tilting lock screws (x2), and rotate the
tilting table to adjust the tilting direction. (Adjustable
range: ±75 °) Since a variable focal lens is used, it is
possible to change the angular field of view. This
lens can also be rotated in the reverse direction, but
the image azimuth is reversed. In this case, the
image azimuth can be modified when the panning
table is rotated to the direction of clockwise panning
(180 °).
Adjustment
Home position
180 °
(clockwise)Panning lock screw
Panning table
160 °
(counterclockwise)
+75 °
–75 °
Adjustable range
q
Tilting lock screw (x2)
37
Horizontal: 27.7 ° (TELE) to 100.8 ° (WIDE)
Vertical: 20.8 ° (TELE) to 73.8 ° (WIDE)
After adjustment, tighten the tilting lock screws (x2) to fix the tilting table.
(Recommended tightening torque: 0.59 N·m {0.44 lbf·ft})
Note:
• When the tilting table is turned to the edge of the adjustable range (±75°), it must be noted that
the shadow of the enclosure may be projected.
Image tilt adjustment
Rotate the azimuth adjustment ring to adjust the azimuth angle of the image. (Adjustable range:
±100 °)
–100 ° +100 °
Adjustable range
Azimuth adjustment ring
38
x Adjust the angular field of view and the focus.
Adjust the angular field of view in accordance with the distance between the camera lens and a
photographic subject. These adjustments shall be performed together with the camera angle
adjustment.
q Loosen the zoom lock knob and move the knob between TELE and WIDE to obtain the appro-
priate angle of view.
Note:
• The focus may not be adjusted appropriately when the zoom ring is positioned at the "W" (or
"T") end. In this case, adjust the focus again by slightly moving the zoom ring to the direction of
"T" (or "W").
w To adjust the angular field of view with a higher zooming effect even after rotating the zoom ring
almost fully in the "T" direction, hold down the auto focus (AF) button/extra optical zoom button
for 5 seconds or more. 2x extra optical zoom will be applied. When the image capture size
under "VGA" is applied, the zoom factor can be adjusted up to 2x without deterioration of
image quality. When holding down the auto focus (AF) button/extra optical zoom button again
for 5 seconds or more, 1x extra optical zoom will be applied.
e Tighten the zoom lock knob.
r When the auto focus (AF) button is pressed, the auto focus (AF) indicator will light for around
10 seconds, and the focus is automatically adjusted.
FOCUS ADJUSTMENT
LOW HIGH
.......
|............
INDICATOR 775 BEST
PEAK HOLD 780 FOCUS
MONITOR
OUT
HEATER
SD CARD / AFAF/EXTRAOPTICAL ZOOM
INITIAL
SET
TOPZoom lock knob
Zoom ring Focus ring
* Do not move the focus ring.
Auto focus (AF) button/
Extra optical zoom button
Loosen
Tighten
39 Important: • Do not move the focus ring. • Defocus may be caused by the reinstalled enclosure. In this case, perform the auto focus func- tion from the setup menu. Note: • If the zoom ring is fully rotated in the "W" direction, the periphery may become dark. In such a case, rotate the zoom ring in the "T" direction for readjustment. • If the zoom lock knob is slightly tightened before the zoom ring is moved, the ring will become stable to ease the fine adjustment. • When shooting in the following place or the following subjects, focus may not be adjusted automatically. In this case, adjust the focus manually from the setup menu. Refer to the Operating Instructions (PDF) for how to perform the manual focus adjustment from the setup menu. • Subj. moving frequently • Subj. with large illuminance change • Subj. with low illuminance • Subj. with reflection or extra brightness • Subj. through a window • Place where the dome cover easily becomes dirty • Subj. with less contrast such as white wall • Subj. with heavy flicker • If the 2x extra optical zoom is applied when "1280x960", "1280x720" (SW355) or "800x600" (SW352) is selected for the image capture size, the image quality will be deteriorated because the effect of Extra Optical Zoom is not provided. • When images in the near-infrared light area change from color to black & white, out-of-focus may be occurred according to the nature of optical property. In this case, the focus can auto- matically be corrected by selecting "Auto" or "Preset" for "Adjusting method" on the setup menu (The focus will not automatically be adjusted according to the illumination level change once the focus is corrected.) Refer to the Operating Instructions (PDF) for how to set "Adjusting method" on the setup menu.
40
c Mount the inner dome that was removed according the steps in page 34 in the reverse proce-
dure. Check to see that the tilting lock screws of the camera are properly engaged in the holes
of the inner dome.
Tighten the screws that have been loosened in step x on page 34 using the bit for tamper-
proof screw (accessory).
Important:
• Securely tighten all the fixing screws (x3) of enclosure. Otherwise, water exposure may cause
damage or malfunction of camera, or camera dropping may result in injury. (Recommended
tightening torque: 0.78 N·m {0.58 lbf·ft})
• Attach the inner dome in accordance with the direction of the lens opening not to change the
lens direction.
• Check if the inner dome and tilting lock screws are firmly fit.
• Remove the protection sheet from the outside of the dome.
AF/EXTRA OPTICAL
ZOOM
LINK ACT
AF/EXTRA
OPTICAL ZOOM
LINK
Groove for
mounting
Cutout for
mounting