Panasonic Network Camera Wv Sw352 Wv Sw355 Installation Guide

							21
z Loosen  two  fixing  screws  on  both  ends  of  the  base  cover  by  using  the  bit  for  tamperproof 
screw (accessory), and remove the base cover (accessory).
  Install the mount bracket (accessory) on the wall/ceiling.
  (For use of the hole A)
B B
B
A
A
A
51 mm {2 inches}
ø27 mm 
{1-1/16 inches}
138 mm 
{5-7/16 inches} 138 mm 
{5-7/16 inches}
For use of the hole B
85 mm 
{3-11/32 inches}
85 mm 
{3-11/32 inches}
For use of the hole A
Cable access hole Mount bracket (accessory)
Center of mount bracket
Female thread for conduit
Mount bracket 
(accessory)
A A
A AB
B
B
B
Base cover (accessory) 
						

							22
Note:
	 •	 Only	 the	same	 type	of	holes,	 A or B, shall 
be used for mounting.
x  Pass the cables through the hole for cable running from the wall or ceiling. 
c   Fix the camera attachment on the mount bracket using the screws supplied with the bracket. 
    Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
Note:
	 •	 For	wall	mounting:
    The  camera  attachment  shall  be  mounted  with  "gTOP"  facing  upward.  (Except  the  case  of 
connecting the conduit upward (
☞ page 20))
	 •	 For	ceiling	mounting:
    The camera attachment shall be mounted with aligning the front side (model number indication 
face) of the camera with the position of the arrow in "hFRONT". 
	 •	 Ensure	 that	any	of	the	 arrows	 on	the	 mount	 bracket	 is	aligned	 with	the	"gTOP"  arrow  on  the 
camera attachment. 
B A
B
A B B
A
A
Mount bracket (accessory)
Camera attachment
FRONTTOP 
						

							23
Important:
	 •	 Before	inserting	the	SDHC/SD	memory	card,	turn	off	the	power	of	the	camera	first.
	 •	 When	inserting	an	SDHC/SD	memory	card,	make	sure	the	direction.
	 •	 Before	 removing	the	SDHC/SD	 memory	card,	select	 "Not	use"	for	"SD	 memory	 card"	on	the	
[SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and 
then  unload  the  SDHC/SD  memory  card.  When  the  SDHC/SD  memory  card  is  inserted  or 
removed  with  the  power  on,  data  in  the  SDHC/SD  memory  card  may  be  damaged.   
(
☞ Operating Instructions (PDF))
z  Detach the enclosure. (☞ Page 34)
x   Insert  an  SDHC/SD  memory  card  fully  into  the 
SDHC/SD  memory  card  slot  until  a  click  is 
heard. 
c Attach the enclosure to the camera. 
 (
☞ Page 40)
v    When  removing  the  SDHC/SD  memory  card 
from  the  SDHC/SD  memory  card  slot,  detach 
the  enclosure  (
☞  page  34),  and  push  the  card 
until  a  click  is  heard.  After  the  SDHC/SD  mem-
ory card is removed, attach the enclosure to the 
camera again. (
☞ Page 40)
Insert/remove an SDHC/SD memory card
Label side 
						

							24
Heater Unit WV-SW3H (option)
	 •	 Installing	this	heater	 unit	enables	 the	camera	 to	operate	 in	a	low-temperature	 environment	of 
–30 °C {–22 °F}  or above. A small fan inside the unit will minimize condensation on the surface 
of  the  enclosure  caused  by  changes  in  ambient  temperature  unless  temperatures  change  too 
rapidly. The fan will stop when there is no possibility of condensation.
	 •	 The	 heater	unit	is	automatically	 turned	on	or	off	 according	 to	the	 temperature	 inside	the	camera	
that is monitored. 
Important:
	 •	 Turning	the	heater	on	and	off	may	disturb	the	camera	images.
	 •	 The	power	supply	of	the	camera	shall	be	turned	off	when	mounting	or	dismounting	the	heater.
    When servicing, pay attention to high temperature on the surface of the heater unit. Disconnect 
the harness and wait until the heater unit cools. 
	 •	 When	 this	product	 is	installed	 and	operated	 in	low	 temperatures	 below	–10	°C	{14	 °F},	 normal	
images may not be obtained immediately after startup. In such a case, wait until the camera is 
warmed up (approx. 2 hours or more) and turn on the power again.
How to install the heater unit
  q  Detach  the  camera’s  enclosure  (☞  page  34)  and  mount  it  in  the  specified  position  with  the 
screw (accessory).
  w  Connect the harness cable to the heater unit connector of the camera.
Important:
	 •	 After	 mounting	 the	heater	 unit,	arrange	 the	harness	 cable	as	shown	 in	the	 illustration	 in	step	 e 
so as not to be tangled round the enclosure, assist wire or equipment inside the camera. 
    
How to install the heater unit 
						

							25
 e  Attach the enclosure to the camera. (☞ Page 40)
Heater unit 
(option) connectorScrew (accessory of 
the heater unit)* 
* Two screws are supplied with the heater unit.  (Of them, 1 for spare) 
						

							26
Caution:
	 •	 FOR	UL	LISTED	MODEL(S),	ONLY	CONNECT	12	V	DC	CLASS	2	POWER	SUPPLY.	
Turn  off  a  circuit  breaker  before  making  a  connection.  Before  starting  the  connection,  prepare  the 
required devices and cables. Note:
	 •	 When	 using	the	mount	 bracket	 (accessory),	 it	is	 possible	 to	connect	 the	cables	 after	mounting	
the camera onto the mount bracket. 
	 •	 Refer	to	page	20	when	connecting	the	conduit.
Connection
Network cable
* PAL model only * PAL model only
RJ-45 (female)
Alarm input/output cable 4P alarm cable (accessory)
Power cable 
(12 V DC) 2P power cable (accessory)
12 V DC (red)
GND (black)
Microphone/line input cable (white) Audio output cable (black)
Power cable 12 V DC
Red Positive
Black Negative
    
z    Connect  the  microphone/line  input  cable  and  the  microphone  (for  use  of  the  audio  reception 
function).
Input impedance:  2 kΩ±10 %
Recommended cable length:  Less than 1 m {3.28'} (for microphone input)
    Less than 10 m {32.8'} (for line input)
Recommended microphone:  Plug-in power type microphone (option)
    Connect a mini plug (ø3.5 mm).
Supply voltage:  2.5 V ±0.5 V
Recommended sensitivity of microphone: −48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
Important:
	 •	 Connect/disconnect	 the	external	 speaker	 cables	or	audio/video	 cables	after	turning	 off	the	
power of the camera and the amplifier. Otherwise, loud noise may come out from the speaker.  
						

							27
x   Connect  an  external  amplifier-embedded  speaker  to  the  audio  output  cable  (for  use  of  the 
audio transmission function).
    Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.). 
	 •	 Recommended	cable	length:	Less	than	10	m	{32.8	ft}
c  Connect the alarm input/output cable.
    
Terminal name Ratings
ALARM OUT, AUX OUT Open collector output (maximum applied voltage: 20 V DC)
Open 4 V DC - 5 V DC by internal pull-up
Close Output voltage 1 V DC or less (50 mA or less)
ALARM IN, DAY/NIGHT IN Non-voltage make contact input (4 V DC - 5 V DC, internally pulled 
up)
OFF Open or 4 V DC - 5 V DC
ON Make contact with GND (required drive current: 1 mA or more)
Note:
	 •	 Check	 if	rating	 of	an	 external	 device	such	as	a	sensor	 is	applicable	 to	the	 rating	 of	this	 product	
by referring to the provided operating instructions.
Specication of 4P alarm cable (accessory)
GND (black)
AUX OUT (gray) (Terminal 3)
ALARM OUT (red) (Terminal 2)
ALARM IN, DAY/NIGHT IN (green) (Terminal 1) 
						

							28
v Connect a LAN cable (category 5e or better, straight, STP*) to the network connector.
    * PAL model only 
b Connect the power cable. 
	 •	 When	using	12	V	DC	power	supply*
1
    Connect the output cable of the AC adaptor to the 2P power cable.
	 •	 When	using	PoE	(IEEE802.3af	compliant)
    Connect  a  LAN  cable  (category  5  or  better,  straight,  STP*
2)  between  a  PoE  device  (such  as  a 
hub) and the network connector of the camera. 
  *1 FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
  *2 PAL model only
Important: 
	 •	 Use	all	4	pairs	(8	pins)	of	the	LAN	cable.	
	 •	 The	maximum	cable	length	is	100	m	{328	feet}.
	 •	 Make	sure	that	the	PoE	device	in	use	is	compliant	with	IEEE802.3af	standard.	
	 •	 When	 connecting	 both	the	12	V	DC	 power	 supply	 and	the	PoE	 device	 for	power	 supply,	 PoE	
will be used for power supply.
	 •	 When	 the	LAN	 cable	 is	disconnected	 once,	reconnect	 the	cable	 after	about	 2	seconds.	 When	
the cable is quickly reconnected, the power may not be supplied from the PoE device. 
						

							29
Waterproof treatment for the cable joint sections
Adequate  waterproof  treatment  is  required  for  the  cables  when  installing  the  camera  with  cables 
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not 
waterproof.
Be  sure  to  use  the  supplied  butyl  rubber  tape  at  the  points  where  the  cables  are  connected  to 
apply waterproof treatment in the following procedure. Failure to observe this or use of a tape other 
than the provided butyl rubber tape (such as a vinyl tape) may cause water leakage resulting in mal-
function.
LAN cable
Alarm input/output cable, power cable, microphone/line input cable, audio output cableImportant: 
	 •	 Waterproof	 treatment	is	also	 to	be	 applied	 to	the	 2P	power	 cable	(accessory),	 the	4P	alarm	
cable (accessory) and other connection cables if they are subject to rain.
Note:
	 •	 How	to	wind	the	supplied	waterproof	butyl	tape
    Stretch  the  tape  by  approx.  twice  (see  the  illustration) 
and  wind  it  around  the  cable.  Insufficient  tape  stretch 
causes insufficient waterproofing.
	 •	 To	 install	this	product	 outdoors,	 be	sure	 to	waterproof	
the cables. Waterproof grade (IEC IP66 or equivalent) is 
applied to this product only when it is installed correctly 
as  described  in  these  operating  instructions  and  appropriate  waterproof  treatment  is  applied. 
The mount brackets are not waterproofed.
    
Wind the tape in a 
half-overlapping manner. 
Wind the tape in a 
half-overlapping manner. 
Wind the tape in a 
half-overlapping manner. 
Wind the tape in a 
half-overlapping manner. 
Stretch the tape to 
about twice.
2x 
						

							30
Connection example when connecting to a network using a 
PoE hub

LAN cable (category 5 or better, straight, STP*)
* PAL model onlyImportant: 
	 •	 The	 video	monitor	 is	used	 for	checking	 the	adjustment	 of	the	 angular	 field	of	view	 when	 install-
ing the camera or when servicing. It is not provided for recording/monitoring use.
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX.
	 •	 Power	 supply	is	required	 for	each	 network	 camera.	 When	using	a	PoE	 device	 (hub),	12	V	DC	
power supply is unnecessary. 
Powered speaker 
(option)
Powered speaker 
(option) Microphone (option)
Microphone (option) Video monitor 
(for adjustment use only)
Video monitor 
(for adjustment use only) PoE device (hub)
LAN cable 
(category 5 or better,  straight, STP*)
LAN cable 
(category 5 or better, straight, STP*) LAN cable 
(category 5 or better, 
straight, STP*)
PC