Panasonic Network Camera Wv Sw352 Wv Sw355 Installation Guide

21
z Loosen  two  fixing  screws  on  both  ends  of  the  base  cover  by  using  the  bit  for  tamperproof 
screw (accessory), and remove the base cover (accessory).
  Install the mount bracket (accessory) on the wall/ceiling.
  (For use of the hole A)
B B
B
A
A
A
51 mm {2 inches}
ø27 mm 
{1-1/16 inches}
138 mm 
{5-7/16 inches} 138 mm 
{5-7/16 inches}
For use of the hole B
85 mm 
{3-11/32 inches}
85 mm 
{3-11/32 inches}
For use of the hole A
Cable access hole Mount bracket (accessory)
Center of mount...

22
Note:
	 •	 Only	 the	same	 type	of	holes,	 A or B, shall 
be used for mounting.
x  Pass the cables through the hole for cable running from the wall or ceiling. 
c   Fix the camera attachment on the mount bracket using the screws supplied with the bracket. 
    Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}
Note:
	 •	 For	wall	mounting:
    The  camera  attachment  shall  be  mounted  with  "gTOP"  facing  upward.  (Except  the  case  of 
connecting the conduit upward (
☞ page 20))
	 •...

23
Important:
	 •	 Before	inserting	the	SDHC/SD	memory	card,	turn	off	the	power	of	the	camera	first.
	 •	 When	inserting	an	SDHC/SD	memory	card,	make	sure	the	direction.
	 •	 Before	 removing	the	SDHC/SD	 memory	card,	select	 "Not	use"	for	"SD	 memory	 card"	on	the	
[SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and 
then  unload  the  SDHC/SD  memory  card.  When  the  SDHC/SD  memory  card  is  inserted  or 
removed  with  the  power...

24
Heater Unit WV-SW3H (option)
	 •	 Installing	this	heater	 unit	enables	 the	camera	 to	operate	 in	a	low-temperature	 environment	of 
–30 °C {–22 °F}  or above. A small fan inside the unit will minimize condensation on the surface 
of  the  enclosure  caused  by  changes  in  ambient  temperature  unless  temperatures  change  too 
rapidly. The fan will stop when there is no possibility of condensation.
	 •	 The	 heater	unit	is	automatically	 turned	on	or	off	 according	 to	the	 temperature	 inside...

25
 e  Attach the enclosure to the camera. (☞ Page 40)
Heater unit 
(option) connectorScrew (accessory of 
the heater unit)* 
* Two screws are supplied with the heater unit.  (Of them, 1 for spare) 

26
Caution:
	 •	 FOR	UL	LISTED	MODEL(S),	ONLY	CONNECT	12	V	DC	CLASS	2	POWER	SUPPLY.	
Turn  off  a  circuit  breaker  before  making  a  connection.  Before  starting  the  connection,  prepare  the 
required devices and cables. Note:
	 •	 When	 using	the	mount	 bracket	 (accessory),	 it	is	 possible	 to	connect	 the	cables	 after	mounting	
the camera onto the mount bracket. 
	 •	 Refer	to	page	20	when	connecting	the	conduit.
Connection
Network cable
* PAL model only * PAL model only
RJ-45 (female)
Alarm...

27
x   Connect  an  external  amplifier-embedded  speaker  to  the  audio  output  cable  (for  use  of  the 
audio transmission function).
    Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.). 
	 •	 Recommended	cable	length:	Less	than	10	m	{32.8	ft}
c  Connect the alarm input/output cable.
    
Terminal name Ratings
ALARM OUT, AUX OUT Open collector output (maximum applied voltage: 20 V DC)
Open 4 V DC - 5 V DC by internal pull-up
Close Output voltage 1 V DC or less (50 mA or less)
ALARM...

28
v Connect a LAN cable (category 5e or better, straight, STP*) to the network connector.
    * PAL model only 
b Connect the power cable. 
	 •	 When	using	12	V	DC	power	supply*
1
    Connect the output cable of the AC adaptor to the 2P power cable.
	 •	 When	using	PoE	(IEEE802.3af	compliant)
    Connect  a  LAN  cable  (category  5  or  better,  straight,  STP*
2)  between  a  PoE  device  (such  as  a 
hub) and the network connector of the camera. 
  *1 FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC...

29
Waterproof treatment for the cable joint sections
Adequate  waterproof  treatment  is  required  for  the  cables  when  installing  the  camera  with  cables 
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not 
waterproof.
Be  sure  to  use  the  supplied  butyl  rubber  tape  at  the  points  where  the  cables  are  connected  to 
apply waterproof treatment in the following procedure. Failure to observe this or use of a tape other 
than the provided...

30
Connection example when connecting to a network using a 
PoE hub

LAN cable (category 5 or better, straight, STP*)
* PAL model onlyImportant: 
	 •	 The	 video	monitor	 is	used	 for	checking	 the	adjustment	 of	the	 angular	 field	of	view	 when	 install-
ing the camera or when servicing. It is not provided for recording/monitoring use.
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX.
	 •	 Power	 supply	is	required	 for	each	 network	 camera.	 When	using	a	PoE	 device...