Panasonic Network Camera Wv Sw352 Wv Sw355 Installation Guide

11
Precautions
Refer installation work to the dealer.
Installation work requires technique and experi-
ences.  Failure  to  observe  this  may  cause  fire, 
electric  shock,  injury,  or  damage  to  this  prod-
uct. 
Be sure to consult the dealer. 
Stop the operation immediately when 
something is wrong with this product. 
When  smoke  goes  up  from  the  product,  the 
smell of smoke comes from the product, or the 
exterior of the product has deteriorated, contin-
ued  use  will  cause  a  fire  or...

12
Do not rub the edges of metal parts with 
your hand. 
Failure to observe this may cause injury. 
Do not touch this product, the power cord 
or the connected cables during thunder. 
(even in the process of work)
Failure  to  observe  this  may  cause  electric 
shock.
Turn the power off when cleaning this 
product. 
Failure to observe this may cause injury. 
[Precautions for use]
This product has no power switch. 
When  turning  off  the  power,  turn  off  a  circuit 
breaker. 
To keep on using with...

13
	 •	 When	some	SDHC/SD	 memory	cards	are	
used  with  this  product,  the  product  may 
not  work  properly  or  performance  deterio-
ration  may  be  caused.  Use  the  SDHC/SD 
memory cards recommended in page 47. 
Code label
The  code  labels  (accessory)  are  required  at 
inquiry  for  trouble.  Use  caution  not  to  lose 
these  labels.  It  is  recommended  to  paste  one 
of the labels onto the CD-ROM case.
Discoloration on the color filter of the 
MOS image sensor
	 •	 When	 continuously...

14
Precautions for installation
This product is designed to be installed 
under eaves.
Install  the  product  under  eaves  to  avoid  direct 
sunlight.
Installing place
Contact  your  dealer  for  assistance  if  you  are 
unsure  of  an  appropriate  place  in  your  particu-
lar environment.
	 •	 Make	sure	that	the	installation	 area	is	
strong  enough  to  hold  this  product,  such 
as a concrete ceiling. 
	 •	 Install	 the	camera	 in	the	 foundation	 area	of	
the architecture or where sufficient...

15
Do not remove or loosen the screws on 
the rear of this product. 
If the screws (7 pcs.) are loosened, water expo-
sure  may  cause  damage  or  malfunction  of  the 
product, or dropping may result in injury.
Radio disturbance
When this product is used near TV/radio anten-
na, strong electric field or magnetic field (near a 
motor,  a  transformer  or  a  power  line),  images 
may be distorted and noise sound may be pro-
duced. 
PoE (Power over Ethernet)
Use  a  PoE  hub/device  that  is  compliant...

16
Major operating controls
Enclosure
Inner dome
MONITOROUT
HEATER
SD CARD / AF
AF/EXTRAOPTICAL ZOOM
INITIAL
SET
TOPTilting table Zoom lock knob
Zoom ring
Focus ring
Tilting lock screw (x2)
Azimuth 
adjustment ring
Audio output cable (black) Network cable
* PAL model only RJ-45 (female)
Alarm input/output cable
Power cable (12 V DC)
Microphone/line input cable (white)
FRONTTOP
Mount bracket (accessory)
Base cover
(accessory)
Camera attachment (accessory) 

17
About the initial set button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing the button. Wait around 2 minutes 
after  releasing  the  button.  The  camera  will  start  up  and  the  settings  including  the  network  settings 
will  be  initialized.  Before  initializing  the  settings,  it  is  recommended  to  write  down  the  settings  in 
advance. Do not turn off the power of the...

18
When installing the camera on a wall or a ceiling, there are two methods as specified below.
	 •	 Using	a	two-gang	junction	box
	 •	 Use	the	supplied	mount	bracketImportant:
	 •	 Procure	 4	screws	 (M4)	to	secure	 the	camera	 attachment	 (accessory)	or	the	 mount	 bracket	
(accessory)  to  a  wall  or  a  ceiling  according  to  the  material  of  the  installation  area.  Do  not  use 
wood screws and nails.
    For  mounting  a  camera  on  a  concrete  ceiling,  use  an  anchor  bolt  (for  M4)  or...

19
Using a two-gang junction box
	 •	 Secure	the	camera	 attachment	 (accessory)	to	the	 two-gang	 junction	box	built	 in	a	wall	 or	ceil-
ing.
Note:
	 •	 For	wall	mounting:
    The camera attachment shall be mounted with "gTOP" facing upward. 
	 •	 For	ceiling	mounting:
    The camera attachment shall be mounted with "hFRONT" facing in the direction of the camera 
front (model number indication face).
Using the mount bracket (accessory)
Note:
	 •	 When	 the	camera	 is	mounted	 on	the...

20
Important:
	 •	 If	 open	wiring	 is	conducted,	 be	sure	 to	use	 conduits	 and	run	the	cables	 inside	the	tubes	 to	pro-
tect the cables from direct sunlight.
	 •	 When	 connecting	 the	conduit	 at	the	 lateral	 or	bottom	 position,	 any	of	the	 arrow	 marks	 on	the	
bracket shall be at the top.
	 •	 When	 connecting	 the	conduit	 upward,	 mount	the	camera	 attachment	 with	the	arrow	 position	
on either left or right side. 
    
    
	 •	 For  installations  on  the  wall,  to  prevent  water  from...