Panasonic Network Camera Wv Sw314 Wv Sw316 Installation Guide
Here you can view all the pages of manual Panasonic Network Camera Wv Sw314 Wv Sw316 Installation Guide. The Panasonic manuals for Security Camera are available online for free. You can easily download all the documents as PDF.
Page 31
31 Note: • When shooting in the following place or the following subjects, focus may not be adjusted automatically. In this case, adjust the focus manually from the setup menu. Refer to the Operating Instructions (included in the CD-ROM) for how to perform the manual focus adjust- ment from the setup menu. • Subj. with large illuminance change • Subj. moving frequently • Subj. with reflection or extra brightness • Subj. with low illuminance • Place where the front cover...
Page 32
![Page 32
32
w To adjust the angular field of view with a higher zooming effect even after adjusting the angular
field of view almost fully in the "T" direction, hold down the focus assist button (F.A.)/extra opti-
cal zoom button for 5 seconds or more. 2x extra optical zoom will be applied. When the image
capture size under "VGA" is applied, the zoom factor can be adjusted up to 2x \
without deterio-
ration of image quality. When holding down the focus assist button (F.A.)/extra optical zoom...](http://img.usermanuals.tech/thumb/58/72241/w300_wv-sw314_wv-sw316_installation_guide_d-31.png "Page 32
32
w To adjust the angular field of view with a higher zooming effect even after adjusting the angular
field of view almost fully in the \"T\" direction, hold down the focus assist button (F.A.)/extra opti-
cal zoom button for 5 seconds or more. 2x extra optical zoom will be applied. When the image
capture size under \"VGA\" is applied, the zoom factor can be adjusted up to 2x \
without deterio-
ration of image quality. When holding down the focus assist button (F.A.)/extra optical zoom...")
32 w To adjust the angular field of view with a higher zooming effect even after adjusting the angular field of view almost fully in the "T" direction, hold down the focus assist button (F.A.)/extra opti- cal zoom button for 5 seconds or more. 2x extra optical zoom will be applied. When the image capture size under "VGA" is applied, the zoom factor can be adjusted up to 2x \ without deterio- ration of image quality. When holding down the focus assist button (F.A.)/extra optical zoom...
Page 33
33
Mount the front cover.
Attach the desiccant (accessory) to the inner bottom side of the front cover along the guide rib, and
mount the front cover.
Desiccant (accessory)Guide rib Fixing screw x4
(3)
(1)
(2) (4)
IMPORTANT:
• Be sure to attach the desiccant (accessory). Refer to the instructions for the desiccant for how to attach it.
SW314
• The tightening torque described below shall be followed for the 4 fixing screws of front cover.
Recommended tightening torque: 0.59 N·m {0.44...
Page 34
![Page 34
34
Attaching the mounting surface on the top surface of the camera body
When the mounting surface is changed to the top surface of the camera bo\
dy
z Remove the 4 sunshield fixing screws from the camera body and remove the sunshield.
x Remove the 4 tripod head fixing screws from the camera body and remove the tripod head.
c Loosen the fixing screw x1 and remove the rear cover, and remove the cap.
v Rotate each cable in the direction of the arrow (clockwise) as illustrated and pass them between
opening...](http://img.usermanuals.tech/thumb/58/72241/w300_wv-sw314_wv-sw316_installation_guide_d-33.png "Page 34
34
Attaching the mounting surface on the top surface of the camera body
When the mounting surface is changed to the top surface of the camera bo\
dy
z Remove the 4 sunshield fixing screws from the camera body and remove the sunshield.
x Remove the 4 tripod head fixing screws from the camera body and remove the tripod head.
c Loosen the fixing screw x1 and remove the rear cover, and remove the cap.
v Rotate each cable in the direction of the arrow (clockwise) as illustrated and pass them between
opening...")
34 Attaching the mounting surface on the top surface of the camera body When the mounting surface is changed to the top surface of the camera bo\ dy z Remove the 4 sunshield fixing screws from the camera body and remove the sunshield. x Remove the 4 tripod head fixing screws from the camera body and remove the tripod head. c Loosen the fixing screw x1 and remove the rear cover, and remove the cap. v Rotate each cable in the direction of the arrow (clockwise) as illustrated and pass them between opening...
Page 35
![Page 35
35
b Mount the tripod head on the top of the camera body with the 4 tripod he\
ad mounting screws
that were removed in the step 2.
IMPORTANT:
• Caution shall be taken to prevent each cable from being caught between the camera body and tripod head.
• Be sure to use the screws that were removed from the tripod head.
Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}
n Secure the camera to the camera mount bracket with the camera fixing screws x3 (accessory).
Pass each cable and the safety...](http://img.usermanuals.tech/thumb/58/72241/w300_wv-sw314_wv-sw316_installation_guide_d-34.png "Page 35
35
b Mount the tripod head on the top of the camera body with the 4 tripod he\
ad mounting screws
that were removed in the step 2.
IMPORTANT:
• Caution shall be taken to prevent each cable from being caught between the camera body and tripod head.
• Be sure to use the screws that were removed from the tripod head.
Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}
n Secure the camera to the camera mount bracket with the camera fixing screws x3 (accessory).
Pass each cable and the safety...")
35
b Mount the tripod head on the top of the camera body with the 4 tripod he\
ad mounting screws
that were removed in the step 2.
IMPORTANT:
• Caution shall be taken to prevent each cable from being caught between the camera body and tripod head.
• Be sure to use the screws that were removed from the tripod head.
Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}
n Secure the camera to the camera mount bracket with the camera fixing screws x3 (accessory).
Pass each cable and the safety...
Page 36
![Page 36
36
m Remove the sunshield backside.
As illustrated, opening up the sunshield in both directions makes it easier to remove the rear
part of the sunshield.
• When installing the camera to a ceiling, the rear part of the sunshield and the fixing screws are not used.
Rear part of sunshield
Fixing screw x2
,
Mount the sunshield on the camera body with the 4 sunshield mounting scr\
ews after removing
the sunshield backside.
• The sunshield is attached to the camera by inserting the protrusions on the...](http://img.usermanuals.tech/thumb/58/72241/w300_wv-sw314_wv-sw316_installation_guide_d-35.png "Page 36
36
m Remove the sunshield backside.
As illustrated, opening up the sunshield in both directions makes it easier to remove the rear
part of the sunshield.
• When installing the camera to a ceiling, the rear part of the sunshield and the fixing screws are not used.
Rear part of sunshield
Fixing screw x2
,
Mount the sunshield on the camera body with the 4 sunshield mounting scr\
ews after removing
the sunshield backside.
• The sunshield is attached to the camera by inserting the protrusions on the...")
36 m Remove the sunshield backside. As illustrated, opening up the sunshield in both directions makes it easier to remove the rear part of the sunshield. • When installing the camera to a ceiling, the rear part of the sunshield and the fixing screws are not used. Rear part of sunshield Fixing screw x2 , Mount the sunshield on the camera body with the 4 sunshield mounting scr\ ews after removing the sunshield backside. • The sunshield is attached to the camera by inserting the protrusions on the...
Page 37
![Page 37
37
Using the CD-ROM
About the CD launcher
Insert the provided CD-ROM into the CD-ROM drive of your PC to start up the CD launch\
er. Then the
License Agreement will be displayed.
• Read the Agreement and choose "I accept the term in the license agreement", and click [OK].
Then the launcher window will be displayed.
• If the launcher window is not displayed, double click the "CDLauncher.exe" file on the CD-ROM.
q
e
t w
r
Using the supplied CD-ROM, the following actions can...](http://img.usermanuals.tech/thumb/58/72241/w300_wv-sw314_wv-sw316_installation_guide_d-36.png "Page 37
37
Using the CD-ROM
About the CD launcher
Insert the provided CD-ROM into the CD-ROM drive of your PC to start up the CD launch\
er. Then the
License Agreement will be displayed.
• Read the Agreement and choose \"I accept the term in the license agreement\", and click [OK].
Then the launcher window will be displayed.
• If the launcher window is not displayed, double click the \"CDLauncher.exe\" file on the CD-ROM.
q
e
t w
r
Using the supplied CD-ROM, the following actions can...")
37 Using the CD-ROM About the CD launcher Insert the provided CD-ROM into the CD-ROM drive of your PC to start up the CD launch\ er. Then the License Agreement will be displayed. • Read the Agreement and choose "I accept the term in the license agreement", and click [OK]. Then the launcher window will be displayed. • If the launcher window is not displayed, double click the "CDLauncher.exe" file on the CD-ROM. q e t w r Using the supplied CD-ROM, the following actions can...
Page 38
![Page 38
38
Installing Panasonic IP setting software
On the CD launcher window, click the [Install] button next to [IP Setting Software] to display the
Panasonic IP setting software installation window. Confirm the following settings before starting the installation.
q
e w
r
q Select the Panasonic IP setting software to install.
w Select where to create the Panasonic IP setting shortcut icon when the Panasonic IP setting software is installed. e Specify which folder on the PC to...](http://img.usermanuals.tech/thumb/58/72241/w300_wv-sw314_wv-sw316_installation_guide_d-37.png "Page 38
38
Installing Panasonic IP setting software
On the CD launcher window, click the [Install] button next to [IP Setting Software] to display the
Panasonic IP setting software installation window. Confirm the following settings before starting the installation.
q
e w
r
q Select the Panasonic IP setting software to install.
w Select where to create the Panasonic IP setting shortcut icon when the Panasonic IP setting software is installed. e Specify which folder on the PC to...")
38 Installing Panasonic IP setting software On the CD launcher window, click the [Install] button next to [IP Setting Software] to display the Panasonic IP setting software installation window. Confirm the following settings before starting the installation. q e w r q Select the Panasonic IP setting software to install. w Select where to create the Panasonic IP setting shortcut icon when the Panasonic IP setting software is installed. e Specify which folder on the PC to...
Page 39
![Page 39
39
Installing the manuals
On the CD launcher window, click the [Install] button next to [Manual] to display the Manual installa-tion window. Confirm the following settings before starting the installation.
q Select which manuals to install. The camera models that the manuals support are displayed in
w "Model List".
w The camera models that are supported by the manuals selected in q are displayed here.
e Select where to create the manuals shortcut icon when the manuals are installed.
r...](http://img.usermanuals.tech/thumb/58/72241/w300_wv-sw314_wv-sw316_installation_guide_d-38.png "Page 39
39
Installing the manuals
On the CD launcher window, click the [Install] button next to [Manual] to display the Manual installa-tion window. Confirm the following settings before starting the installation.
q Select which manuals to install. The camera models that the manuals support are displayed in
w \"Model List\".
w The camera models that are supported by the manuals selected in q are displayed here.
e Select where to create the manuals shortcut icon when the manuals are installed.
r...")
39 Installing the manuals On the CD launcher window, click the [Install] button next to [Manual] to display the Manual installa-tion window. Confirm the following settings before starting the installation. q Select which manuals to install. The camera models that the manuals support are displayed in w "Model List". w The camera models that are supported by the manuals selected in q are displayed here. e Select where to create the manuals shortcut icon when the manuals are installed. r...
Page 40
40 Configure the network settings of the camera using the Panasonic IP setting software It is possible to perform the network settings of the camera using the IP setup software on the pro- vided CD-ROM. When using multiple cameras, it is necessary to configure the network settings of each camera independently. If the Panasonic IP setting software does not work, configure the network settings of the camera and the PC individually on the "Network" page of...