Panasonic Network Camera Wv Sw314 Wv Sw316 Installation Guide

21
v  Remove the screws from the mounting boss of the safety wire and the mounting boss of the cable clamp. 
b  Secure the safety wire with the screw from the mounting boss. Then, bundle the wire and the cable 
using the cable clamp and secure them with each screw from the mounting boss as illustrated.
IMPORTANT:
	 •	 Ensure that the safety wire is firmly secured.  
Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}
Connection
Caution:
	 •	 FOR	UL	LISTED	MODEL(S),	ONLY	CONNECT	12	V	DC	CLASS	2	POWER...

22
v  Connect a LAN cable (category 5e or better, straight, STP*) to the network connector.
   * E model only
b  Connect the power cable. 
	 •	 When	using	12	V	DC	power	supply*
1 SW316L SW316
   Connect the output cable of the AC adaptor to the 2P power cable.
	 •	 When	using	PoE	(IEEE802.3af	compliant)
   Connect a LAN cable (category 5 or better, straight, STP*
2) between a PoE device (such as a 
hub) and the network connector of the camera. 
  *1  FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2...

23
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera with cables 
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not 
waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to apply 
waterproof treatment in the following procedure. Failure to observe this or use of a tape other than 
the provided waterproof tape (such as a vinyl...

24
Connection example when connecting to a network using a 
PoE hub

LAN cable (category 5 or better, straight, STP*)
* E model onlyIMPORTANT: 
	 •	 The	 monitor	 for	 adjustment	 is	 used	 for	 checking	 the	 adjustment	 of	 the	 angular	 field	 of	 view	 when installing the camera or when servicing. It is not provided for recording/monitoring use.
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX.
	 •	 Power	 supply	 is	 required	 for	 each	 network	 camera.	 When	 using...

25
Secure the camera mount bracket when the camera is directly 
installed on a wall
Use 4 screws (locally 
procured) to secure the 
camera mount bracket to a 
wall or a junction box (locally 
procured).
	 •	 If	a	junction	box	is	used,	putting the boxes side by 
side is recommended as 
illustrated. 
(Use unused 
junction boxes to pass 
cables through for easy 
cabling.
)
When the camera is installed on a wall using the adapter box  
(E model only)
  z
 Use 4 screws (locally 
procured) to secure the...

26
	 •	 If	a	junction	box	is	used, putting the 
boxes side by side 
is recommended 
as shown in the 
illustration at right. 
(Use unused 
junction boxes to 
pass cables 
through for easy 
cabling.)
  x Attach the camera mount bracket to the 
left or right hinges of adapter box.
IMPORTANT: 
	 •	 Ensure	that	the	adaptor	box	mounting	screws	 (accessory) are firmly secured. 
Recommended tightening torque: 
M4: 0.78 N·m {0.58 lbf·ft}
	 •	 Ensure	that	the	mounting	screws	for	adaptor	 box/ camera mount bracket...

27
  c Secure the mount bracket 
cover x2 (accessories) to the 
camera mount bracket with the 
2 mount bracket cover screws 
(accessories).
IMPORTANT: 
	 •	 Ensure	that	the	mount	bracket	cover	 screws (accessory) are firmly secured. 
Recommended tightening torque: 
0.59 N·m {0.44 lbf·ft}
Mount bracket cover x2
(accessories)
Mount bracket cover screw x2 
(M3 x 6) (accessories) Camera mount bracket 

28
IMPORTANT:
	 •	 Before	inserting	an	SDHC/SD	memory	card,	turn	off 	the	power	of	the	camera	first.
	 •	 When	inserting	an	SDHC/SD	memory	card,	make	sure	the	direction.
	 •	 Before	 removing	 the	 SDHC/SD	 memory	 card,	 select	 "Not	 use"	 for	 "SD	 memory	 card"	 on	 the	 [SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and 
then unload the SDHC/SD memory card. When the SDHC/SD memory card is inserted or 
removed with the power on,...

29
z Be sure to view the monitor for adjustment when the camera angle is adjusted.
Supply power to this unit, connect the monitor for adjustment (e.g. a small LCD) to the monitor 
output jack, and adjust the camera angle (turn off the power after view angle adjustment for safety).
q Loosen the 4 fixing screws of the front cover to remove the front cover.
w   Connect the monitor output jack and the monitor for adjustment with the \
RCA pin cable 
(locally procured).
	(This	illustration	represents...

30
 x  Adjust the angular field of view and the focus. 
   Adjust the angular field of view in accordance with the distance between the camera lens and a 
photographic subject. These adjustments shall be performed together with\
 the camera angle 
adjustment.
  
Auto focus (AF) button
TELE buttonWIDE button
When adjusting the angular field of view and the focus from the setup menu
Refer to the Operating Instructions (included in the CD-ROM) for how to perform the manual focus 
adjustment from the setup...