Panasonic Network Camera Wv Sw314 Wv Sw316 Installation Guide

							21
v  Remove the screws from the mounting boss of the safety wire and the mounting boss of the cable clamp. 
b  Secure the safety wire with the screw from the mounting boss. Then, bundle the wire and the cable 
using the cable clamp and secure them with each screw from the mounting boss as illustrated.
IMPORTANT:
	 •	 Ensure that the safety wire is firmly secured.  
Recommended tightening torque: 0.59 N·m {0.44 lbf·ft}
Connection
Caution:
	 •	 FOR	UL	LISTED	MODEL(S),	ONLY	CONNECT	12	V	DC	CLASS	2	POWER	SUPPLY.	
Turn off a circuit breaker before making a connection. Before starting the connection, prepare the 
required devices and cables.
Network cableLAN cable(category 5 or better, straight, STP*)
RJ-45 (female)
Alarm input/output cable
4P alarm cable (accessory)
Power cable 
(12 V DC) 2P power cable
(accessory)
12 V DC (red)GND (black)
Microphone/line input cable (white) Audio output cable (black)
z   Connect the microphone/line input cable and the microphone (for use of the audio reception 
function). 
SW316L SW316
Input impedance:  2 kΩ±10 %
Recommended cable length:  Less than 1 m {3.28'} (for microphone input)
   Less than 10 m {32.8'} (for line input)
Recommended microphone:  Plug-in power type microphone (option)
   Connect a mini plug (ø3.5 mm).
Supply voltage:  2.5 V ±0.5 V
Recommended sensitivity of microphone: −48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
IMPORTANT:
	 •	 Connect/disconnect the external speaker cables or audio/video cables after turning off the 
power of the camera and the amplifier. Otherwise, loud noise may come out from the speaker. 
x   Connect an external amplifier-embedded speaker to the audio output cable (for use of the 
audio transmission function). 
SW316L SW316
   Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.). 
	 •	 Recommended	cable	length:	Less	than	10	m	{32.8	ft}
(This illustration represents WV-SW316.)

LAN cable (category 5 or better, straight, STP*)
* E model only 
						

							22
v  Connect a LAN cable (category 5e or better, straight, STP*) to the network connector.
   * E model only
b  Connect the power cable. 
	 •	 When	using	12	V	DC	power	supply*
1 SW316L SW316
   Connect the output cable of the AC adaptor to the 2P power cable.
	 •	 When	using	PoE	(IEEE802.3af	compliant)
   Connect a LAN cable (category 5 or better, straight, STP*
2) between a PoE device (such as a 
hub) and the network connector of the camera. 
  *1  FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
  *2  E model only
IMPORTANT: 
	 •	 Use	all	4	pairs	(8	pins)	of	the	LAN	cable.	
	 •	 The	maximum	cable	length	is	100	m	{328	feet}.
	 •	 Make	sure	that	the	PoE	device	in	use	is	compliant	with	IEEE802.3af	standard.	
	 •	 When	 connecting	 both	 the	 12	 V	 DC	 power	 supply	 and	 the	 PoE	 device	 for	 power	 supply,	 PoE	 will be used for power supply.
	 •	 When	the	LAN	cable	is	disconnected	once,	reconnect	the	cable	after	about	2	seconds.	When	 the cable is quickly reconnected, the power may not be supplied from the PoE device.
c  Connect the alarm input/output cable. SW316L SW316
  
Terminal name Ratings
ALARM OUT, AUX OUT Open collector output (maximum applied voltage: 20 V DC) Open 4 V DC - 5 V DC by internal pull-up
Close Output voltage 1 V DC or less (50 mA or less)
ALARM IN, DAY/NIGHT IN
Non-voltage make contact input (4 V DC - 5 V DC, internally pulled 
up)
OFF Open or 4 V DC - 5 V DC
ON Make contact with GND (required drive current: 1 mA or more)
Note:
	 •	 Check	if	rating	of	an	external	device	such	as	a	sensor	is	applicable	to	the	rating	of	this	product	 by referring to the provided operating instructions.
Specication of 4P alarm cable (accessory)
GND (black)
AUX OUT (gray) (Terminal 3)
ALARM OUT (red) (Terminal 2)
ALARM IN, DAY/NIGHT IN (green) (Terminal 1) 
						

							23
Waterproof treatment for the cable joint sections
Adequate waterproof treatment is required for the cables when installing the camera with cables 
exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not 
waterproof.
Be sure to use the supplied waterproof tape at the points where the cables are connected to apply 
waterproof treatment in the following procedure. Failure to observe this or use of a tape other than 
the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting in malfunc-
tion.
LAN cable
Alarm input/output cable, power cable, microphone/line input cable, audio output cable 
SW316L SW316
IMPORTANT: 
	 •	 Waterproof	 treatment	 is	 also	 to	 be	 applied	 to	 the	 2P	 power	 cable	 (accessory),	 the	 4P	 alarm	 cable (accessory) and other connection cables if they are subject to rain.
Note:
        How to wind the supplied waterproof tape
	 •	 Stretch	 the	 tape	 by	 approx.	 twice	 (see	 the	 illustration)	 and wind it around the cable. Insufficient tape stretch 
causes insufficient waterproofing.
	 •	 Make	 sure	 to	 wind	 the	 tape	 so	 that	 it	 does	 not	 press	 down on the hook of the network cable.
	 • 	 To 	 install	 this	 product	 outdoors,	 be	 sure	 to	 waterproof	
the cables. Waterproof grade (IEC IP66 or equivalent) 
is applied to this product only when it is installed cor -
rectly as described in these operating instructions and 
appropriate waterproof treatment is applied. The mount 
brackets are not waterproofed.
    
Wind the tape in a 
half-overlapping manner. 
Wind the tape in a 
half-overlapping manner. 
Wind the tape in a 
half-overlapping manner. 
Wind the tape in a 
half-overlapping manner. 
Stretch the tape to 
about twice.
2x
hook 
						

							24
Connection example when connecting to a network using a 
PoE hub

LAN cable (category 5 or better, straight, STP*)
* E model onlyIMPORTANT: 
	 •	 The	 monitor	 for	 adjustment	 is	 used	 for	 checking	 the	 adjustment	 of	 the	 angular	 field	 of	 view	 when installing the camera or when servicing. It is not provided for recording/monitoring use.
	 •	 Use	a	switching	hub	or	a	router	which	is	compliant	with	10BASE-T/100BASE-TX.
	 •	 Power	 supply	 is	 required	 for	 each	 network	 camera.	 When	 using	 a	 PoE	 device	 (hub),	 12	 V	 DC	 power supply is unnecessary. 
Powered speaker 
(option)
Powered speaker 
(option) Microphone (option)
Microphone (option)Monitor for adjustment (for adjustment use only)
Monitor for adjustment 
(for adjustment use only) PoE device (hub)
LAN cable 
(category 5 or better,  straight, STP*)
LAN cable 
(category 5 or better, straight, STP*) LAN cable 
(category 5 or better, 
straight, STP*)
PC 
						

							25
Secure the camera mount bracket when the camera is directly 
installed on a wall
Use 4 screws (locally 
procured) to secure the 
camera mount bracket to a 
wall or a junction box (locally 
procured).
	 •	 If	a	junction	box	is	used,	putting the boxes side by 
side is recommended as 
illustrated. 
(Use unused 
junction boxes to pass 
cables through for easy 
cabling.
)
When the camera is installed on a wall using the adapter box  
(E model only)
  z
 Use 4 screws (locally 
procured) to secure the 
adapter box (accessory) to a 
wall or a junction box (locally 
procured).
Camera mount bracket
83.5 mm
{3-1/4"}
46 mm 
{1-13/16"}
Mounting screw x4 
(locally p
rocured) Cable access hole
6 mm (W) x 10 mm (L) {1/4" (W) x 3/8" (L)} (long hole)
20 mm 
{13/16"}
46 mm {1-13/16}Unused 
junction boxes
6 mm (W) x 10 mm (L) {1/4 (W) x 3/8 (L)} (long hole) 
83.5 mm
{3-1/4}
Camera mount bracket
Mounting screw x4 
(locally procured)
Junction boxes
46 mm 
{1-13/16}
View from above (internal)
20 mm {13/16}
83.5 mm
{3-1/4}
Cable access hole (used for wiring)
(G3/4 internal thread)
Mounting screw x4
(locally procured) Cable access hole 
Adapter box (accessory)
6 mm (W) x 10 mm (L) 
{1/4 (W
) x 3/8 (L)} 
(long hole)
TO P 
						

							26
	 •	 If	a	junction	box	is	used, putting the 
boxes side by side 
is recommended 
as shown in the 
illustration at right. 
(Use unused 
junction boxes to 
pass cables 
through for easy 
cabling.)
  x Attach the camera mount bracket to the 
left or right hinges of adapter box.
IMPORTANT: 
	 •	 Ensure	that	the	adaptor	box	mounting	screws	 (accessory) are firmly secured. 
Recommended tightening torque: 
M4: 0.78 N·m {0.58 lbf·ft}
	 •	 Ensure	that	the	mounting	screws	for	adaptor	 box/ camera mount bracket (accessory) are 
firmly secured.  
Recommended tightening torque:  
M5: 1.86 N·m {1.37 lbf·ft}
Note: 
	 •	 The	right	or	left	hinges	of	the	adapter	 box shall be selected so as to prevent 
the motion of the camera mount bracket 
from being interfered with by obstruc-
tions such as a wall when the camera 
mount bracket is connected to the hing-
es of the adapter box.
Mounting screw x4
(locally procured)
6 mm (W) x 10 mm (L) 
{1/4 (W
) x 3/8 (L)}
 (long hole)
46 mm 
{1-13/16} Unused junction 
boxes
Junction boxes
83.5 mm
{3-1/4}
TO
PView from above (internal)
Adaptor box mounting screw (M4 x 35)
Hinges
Adapter box
Camera mount bracket
Mounting screw for adapter box/
camera mount bracket x4 (M5 x 20)
(This illustration represents WV-SW316.) 
						

							27
  c Secure the mount bracket 
cover x2 (accessories) to the 
camera mount bracket with the 
2 mount bracket cover screws 
(accessories).
IMPORTANT: 
	 •	 Ensure	that	the	mount	bracket	cover	 screws (accessory) are firmly secured. 
Recommended tightening torque: 
0.59 N·m {0.44 lbf·ft}
Mount bracket cover x2
(accessories)
Mount bracket cover screw x2 
(M3 x 6) (accessories) Camera mount bracket 
						

							28
IMPORTANT:
	 •	 Before	inserting	an	SDHC/SD	memory	card,	turn	off 	the	power	of	the	camera	first.
	 •	 When	inserting	an	SDHC/SD	memory	card,	make	sure	the	direction.
	 •	 Before	 removing	 the	 SDHC/SD	 memory	 card,	 select	 "Not	 use"	 for	 "SD	 memory	 card"	 on	 the	 [SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and 
then unload the SDHC/SD memory card. When the SDHC/SD memory card is inserted or 
removed with the power on, data in the SDHC/SD memory card may be damaged.   
(
☞ Operating Instructions (included in the CD-ROM))
z  Loosen the 4 fixing screws of the front cover to 
remove the front cover.
x  Insert an SDHC/SD memory card fully into the 
SDHC/SD memory card slot until a click is 
heard. 
c  Attach the front cover to the camera. 
  (
☞ Page 33)
v   When removing the SDHC/SD memory card 
from the SDHC/SD memory card slot, detach 
the front cover by following step 1, and push 
the card until a click is heard. After the SDHC/
SD memory card is removed, attach the front 
cover to the camera again. (
☞ Page 33)
Insert/remove	 an	SDHC/SD	 memory	card	(WV-SW316L/WV-SW316	 Only)
Label side 
						

							29
z Be sure to view the monitor for adjustment when the camera angle is adjusted.
Supply power to this unit, connect the monitor for adjustment (e.g. a small LCD) to the monitor 
output jack, and adjust the camera angle (turn off the power after view angle adjustment for safety).
q Loosen the 4 fixing screws of the front cover to remove the front cover.
w   Connect the monitor output jack and the monitor for adjustment with the \
RCA pin cable 
(locally procured).
	(This	illustration	represents	WV-SW316.)
e Repeat the steps (1) and (2) to adjust the camera angle.
  (1) Loosen the panning lock screw and rotate the camera head horizontally to adjust panning.
  (2) Loosen the tilting lock screw and rotate the camera head vertically to adjust tilting.
  (3) Tighten the panning lock screw and tilting lock screw after camera angle adjustment.
IMPORTANT:
	 •	
After camera angle adjustment, the panning lock screw and tilting lock screw shall be securely tightened.  
Recommended tightening torque: 2.45 N·m {1.8 lbf·ft}
Tilting lock screw
Panning lock screw
Notes:
	 •	 Use	a	hexagonal	wrench	with	width	across	flats	of	4	mm	(locally	procured)	to	loosen	or	tighten	 the panning lock screw and tilting lock screw.
	 •	 Approximately	1	rotation	of	loosening	the	panning	lock	screw	and	tilting	lock	screw	allows	cam- era angle adjustment. Do not loosen the screws beyond necessity.
	 •	 The	camera	body	shall	be	held	when	the	panning	lock	screw	or	tilting	lock	screw	is	loosened.
	 •	 Focus	 adjustment	 (
☞ page 30-32) shall be performed at the same time panning and tilting 
adjustments are performed.
Adjustment
Fixing screw x4
Front cover
Monitor output jack 
						

							30
 x  Adjust the angular field of view and the focus. 
   Adjust the angular field of view in accordance with the distance between the camera lens and a 
photographic subject. These adjustments shall be performed together with\
 the camera angle 
adjustment.
  
Auto focus (AF) button
TELE buttonWIDE button
When adjusting the angular field of view and the focus from the setup menu
Refer to the Operating Instructions (included in the CD-ROM) for how to perform the manual focus 
adjustment from the setup menu.
When adjusting the angular field of view and the focus with the panel of\
 the camera
  q  Press the TELE or WIDE buttons to move the knob between TELE and WIDE to o\
btain the 
appropriate angular field of view.
Note:
	 •	 While	the	button	is	held	down,	the	angle	of	the	view	moves	in	the	"T"	or	"W"	direction.
	 •	 When	the	angular	field	of	view	is	adjusted	on	the	TELE	side,	optical	zoom	is	applied	until	3.2x,	 and if there are any adjustments above this, extra optical zoom is applied.
	 •	 When	the	image	capture	size	under	"VGA"	is	applied,	the	zoom	factor	can	be	adjusted	up	to	 2x without deterioration of image quality.
	 •	 The	zooming	factor	is	displayed	on	the	top	right	of	the	screen.
	 •	
When using the TELE or WIDE buttons to perform operations, the zoom fact\
or stops once at 3.2x. If 
operations are continued, the angle of the view can be moved even more in the "T" or "W" directions.
  w  When the auto focus (AF) button is pressed, the auto focus (AF) indicator will light for around 
10 seconds, and the focus is automatically adjusted. 
IMPORTANT: 
	 •	 Do	not	touch	the	lens.
	 •	 Defocus	 may	 be	 caused	 by	 the	 reinstalled	 front	 cover.	 In	 this	 case,	 perform	 the	 auto	 focus	 function from the setup menu.