Panasonic Network Camera Wv Sw314 Wv Sw316 Installation Guide

11
Do not touch this product, the power cord 
or the connected cables during thunder. 
(even in the process of work)
Failure to observe this may cause electric shock.
Keep SDHC/SD memory cards (option) 
away from infants and children. 
SW316L 
SW316Otherwise, they may swallow the cards by mis-
take.
In this case, consult a doctor immediately.
The measures of protection against snow-
fall shall be taken.
In areas where lots of snow accumulates, the 
weight of snow may cause the product to fall 
resulting...

12
Transmission interval
Image transmission interval may become slow 
depending on the network environment, PC 
performance, shooting subject, access num-
ber, etc. 
About SDHC/SD memory card 
SW316L 
SW316
	 •	 Before	 inserting	 the	 SDHC/SD	 memory	card, turn off the power of this product 
first. Otherwise, it may cause malfunction 
or damage data recorded on the SDHC/
SD memory card. Refer to page 28 for 
descriptions of how to insert/remove an 
SDHC/SD memory card. 
	 •	 When	using	a	SDHC/SD	memory...

13
AVC Patent Portfolio License
THIS PRODUCT IS LICENSED UNDER THE 
AVC PATENT PORTFOLIO LICENSE FOR THE 
PERSONAL USE OF A CONSUMER OR 
OTHER USES IN WHICH IT DOES NOT 
RECEIVE REMUNERATION TO (i) ENCODE 
VIDEO IN COMPLIANCE WITH THE AVC 
STANDARD ("AVC VIDEO") AND/OR (ii) 
DECODE AVC VIDEO THAT WAS ENCODED 
BY A CONSUMER ENGAGED IN A 
PERSONAL ACTIVITY AND/OR WAS 
OBTAINED FROM A VIDEO PROVIDER 
LICENSED TO PROVIDE AVC VIDEO. NO 
LICENSE IS GRANTED OR SHALL BE 
IMPLIED FOR ANY OTHER USE....

14
Precautions for installation
Installing place
Contact your dealer for assistance if you are 
unsure of an appropriate place in your particu-
lar environment.
	 •	 Make	 sure	 that	 the	 installation	 area	 is	strong enough to hold this product, such 
as a concrete ceiling. 
	 •	 Install	the	camera	in	the	foundation	area	of	 the architecture or where sufficient strength 
is assured.
	 •	 If	 a	 wall	 or	 ceiling	 board	 such	 as	 plaster	 board is too weak to support the total 
weight, the area shall...

15
Radio disturbance
When this product is used near TV/radio anten-
na, strong electric field or magnetic field (near a 
motor,  a  transformer  or  a  power  line),  images 
may be distorted and noise sound may be pro-
duced. 
Take notice of humidity.
Install  this  product  when  the  humidity  is  low.  If 
this  product  is  installed  during  rainfall  or  at  a 
high  humidity,  the  inside  may  be  exposed  to 
moisture  and  the  front  cover  may  become 
foggy.
Heater unit
This  product  is...

16
Major operating controls
MONITOROUT
HEATER
SD CARD / AF
AF/EXTRAOPTICAL ZOOM
INITIAL
SET
TOPTilting table Zoom lock knob
Zoom ring
Focus ring
Tilting lock screw (x2)
Azimuth 
adjustment ring
Audio output cable (black) Network cable RJ-45 (female)
Alarm input/output cable
Power cable (12 V DC)
Microphone/line input cable (white)
Rear part of sunshieldSunshield
Rear cover
Safety wire
Panning lock screw
Tilting lock screw
Front cover
Camera mount bracket
(accessory)
(This illustration represents WV-SW316.) 

17
Access indicator (lit when accessing)Link indicator (lit when linking)
Auto focus (AF) buttonInitial set button
»WV-SW316L/WV-SW316¼
WIDE button
TELE button
SDHC/SD memory card slot
SD memory card error indicator/ 
Auto focus indicator 
(blinks when adjusting auto focus) Mount bracket cover x2 
(accessories)
»WV-SW314¼
Access indicator (lit when accessing)
Link indicator (lit when linking)
Initial set button
Focus assist (F.A.) button/
Extra optical zoom button
(This illustration represents...

18
WV-SW316LWV-SW316
Lens
IR LED
Lens cover
Monitor output jack
Packing
Lens
Focus lock knob
Desiccant attachment position Monitor output jack Zoom lock knob
Lens cover
»
WV-SW314 ¼
Packing 

19
IMPORTANT:
	 •	 Prepare	 the	 mounting	 screws	 according	 to	 the	 material	 of	 the	 area	 where	 the	 camera	 mount	 bracket and the adapter box are to be installed. In this case, wood screws and nails should not 
be used. Recommended tightening torque M4: 1.57 N·m {1.16 lbf·ft}
	 •	 Required	pull-out	capacity	of	a	single	screw/bolt	is	196	N	{44.06	lbf}	or	more.
	 •	 If	a	wall	or	ceiling	board	such	as	plaster	board	is	too	weak	to	support	the	total	weight,	the	area	 shall be sufficiently...

20
Secure the camera to the camera mount bracket
The tilt angle is locked downward at shipment.
z  Loosen the tilting lock screw approx. 1 rotation and adjust the tilt angle of the camera to the 
horizontal position.
x Tighten the tilting lock screw again after tilt angle adjustment.
Note:
	 •	 Use	a	hexagonal	wrench	with	width	across	flats	of	4	mm	(locally	procured)	to	loosen	or	tighten	 the tilting lock screw.
Tilting lock screw
Camera main body
Approx. 90°Horizontal
c  Pass each cable and the safety...