Panasonic Network Camera Wv Np1004 Network Operating Instructions

51
Initialize/restart the camera [Initialization]
Click the [Initialization] tab of the Maintenance page. (☞page 49)
Initialization of the settings and data of the camera and restarting of \
the camera can be performed on this page. 
[Initialize setup data]
Click the [Execute] button to reset the settings to the
default settings. However, the network settings will not
be reset.
It is impossible to operate the camera for around 2 min-
utes after the initialization.
[Initialize HTML data]
Click the...

52
Configure the Camera Settings such as Image Quality, Brightness, etc.
The following are descriptions of how to configure the settings such as \
image quality, brightness, privacy zone and
flange-back length, etc. 
The settings can be configured in the following methods.•Configure the settings using a PC
The setting can be configured on the [Camera] tab of the Camera setup \
page. Refer to page 27 for further infor-
mation.
• Configure the settings using the operation buttons on the camera
The settings...

53
The following are available for the shutter speed.
When Full scan is selected for the scan mode: 
OFF (1/15), 1/30, 1/50, 1/60, 1/100, 1/250, 1/500,
1/1000, 1/2000, 1/4000, 1/10000
When Partial scan is selected for the scan mode: 
OFF (1/60), 1/100, 1/250, 1/500, 1/1000, 1/2000,
1/4000, 1/10000
Default:1/30
Notes:
•When ALC+ or ELC is selected for ALC/ELC,
shutter speed selection is unavailable. The --- indi-
cation will be displayed for the shutter speed.
• When a fast shutter speed is selected,...

54
How to adjust white balance(When AWC is selected WHITE BAL)
qSelect AWC for WHITE BAL, and then press
the [Left] button to switch to AWC
→PUSH SW.
wPress the [SET] button to adjust white balance.
The PUSH SW part will be highlighted in the
process of the adjustment. When the highlighted
indication returns to normal indication, adjust-
ment of white balance is complete.
ePress the [Right] button to select AWC.
Refer to page 61 for descriptions of how to adjust
white balance finely.
Note:
Operating...

55
Configure the settings relating to the flange-back [BACK-
FOCUS]
Select the method of the flange-back length adjustment and adjust the fl\
ange-back length minutely. The settings can
be configured on the BACK-FOCUS SETUP page. Before adjusting the flang\
e-back length, adjust the lens first. 
(
☞Operating instructions)
Refer to the operating instructions for descriptions of how to display t\
he BACK-FOCUS SETUP page using the but-
tons on the camera. Refer to page 27 for how to display the BACK-FOCUS...

56
Note:AUTO Advantage:
The flange-back length position will
be most appropriate even under the environment
where light sources changes since the flange-
back length is automatically adjusted when
switching between the color image display and
the BW image display.
Disadvantage:Images will be out of focus for
several seconds while adjusting the flange-back
length automatically.
PRESET Advantage:
Defocusing may not occur since the
flange-back length position moves to the preset
position quickly. It is...

57
Configure the settings on the SPECIAL SETUP page
[SPECIAL SETUP]
Configure the settings relating to image quality can be configured on th\
e SPECIAL SETUP page. The settings can
be configured on the SPECIAL SETUP page.
Refer to the operating instructions for descriptions of how to display t\
he SPECIAL SETUP page using the buttons
on the camera. Refer to page 27 for how to display the SPECIAL SETUP p\
age using a PC.
SPECIAL SETUP page
[CHROMA GAIN]
Adjust the chroma level (color density).
Color...

58
Configure the network settings [NETWORK]
Configure the network settings. When connecting the camera to a network,\
 it is necessary to configure the network
settings such as IP address, etc.
The settings can be configured on the NETWORK SETUP page. Refer to the\
 operating instructions for descriptions
of how to display the NETWORK SETUP page. Refer to page 27 for how to \
display the NETWORK SETUP page
using a PC.
Notes:
•Configure the network settings on the NETWORK SETUP page when network \...

59
Configure the detailed settings
The following are descriptions of how to edit the camera title, adjust w\
hite balance, etc. on the detailed setup menu.
The camera title can be edited and displayed on the screen
The camera title can be edited and displayed on the screen. Up to 16 cha\
racters are available for the camera title.
Step 1
Select ON for CAMERA ID on the CAMERA
SETUP page.
→The camera ID edit page will be displayed.
Step 2
Move the cursor onto the desired character and press
the [SET]...

60
Compensate backlight
Set an area where backlight is to be compensated.
Step 1
Select ALC for ALC/ELC on the CAMERA SETUP
page.
→The ALC CONT page will be displayed.
Step 2
Move the cursor onto BLC and select ON or OFF.
ON:Backlight will be compensated automatically. (→To
step 6)
OFF:Manually set an area where backlight is to be
compensated. (
→To step 3)
Default:OFF
Step 3
Move the cursor onto MASK SET and press the [SET]
button.
→The mask setup window will be displayed.
Step 4
Mask a bright area on...