Panasonic Network Camera Wv Np1004 Network Operating Instructions

21
Configure the settings relating to the NTP server [NTP]
Click the [NTP] tab on the Basic setup page. (☞page 19)
The settings relating to the NTP server such as the NTP server address, \
port number, etc. can be configured on this
page. 
[Time adjustment]
Select the time adjustment method from the following.
Time adjusted by the selected method will be used as
the standard time of the camera. 
Manual setup:Time set on the [Basic] tab on the
Basic setup page will be used as the standard time
of the...

22
[About SD memory card]
Select Use or Not use to determine whether or not to
use the SD memory card.
Important:
•Before removing the SD memory card from the cam-
era, it is necessary to select Not use first.
• After inserting the SD memory card, it is necessary
to select Use to use the SD memory card. 
[Notification for SD memory card]
When the E-mail notification function or the
Panasonic alarm protocol function is used to notify of
the remaining space of the SD memory card, select a
timing to be...

[Scan mode]
Select Full scan or Partial scan for the scan mode of
JPEG/MPEG-4 images.
Default:Full scan
Full scan
Images of up to 1280 (H) x 960 (V) pixels can be cap-
tured. The frame rate will be limited to up to 15 frames
(per second) since the progressive scan is used.
Note: 
The refresh interval of analog video output will also
become slow.
Partial scan
Images of up to 960 (H) x 720 (V) pixels can be cap-
tured at high speed (up to 30 frames per second for net-
work output, up to 60 fields per...

24
When Full scan is selected for Scan mode, the
maximum refresh interval for JPEG will be 15 fps
and the frame rate of the analog output will be 1/2.
[Image capture size]
Select Use or Not use for the image capture size of
JPEG image according to the selected scan mode.
When Full scan is selected for the scan mode
1280 x 960/VGA/QVGA
When Partial scan is selected for the scan mode
960 x 720/VGA/QVGA
Default:VGA
Note:
The parameters selected for Image capture size of
both the Alarm image setup section on...

25
Configure the settings relating to MPEG-4 image [JPEG/MPEG-4]
Click the [JPEG/MPEG-4] tab on the Camera setup page. (☞page 23)
Configure the settings such as Max bit rate (per 1 client), Image c\
apture size and Image quality on this page.
Refer to page 23 for further information about the settings relating to \
JPEG images.
[Scan mode]
Refor to page 23.
[MPEG-4 transmission]
Select ON or OFF to determine whether or not to
transmit MPEG-4 images.
ON:Transmits MPEG-4 images.
OFF:Does not transmit...

26
Important:
•Depending on the PC in use for monitoring, the mul-
ticast port number may be already in use. In this
case, it may be impossible to monitor images.
Change the multicast port number.
•W hen transmitting MPEG-4 image via a network, the
transmitted image sometimes may not be displayed.
In this case, refer to the network administrator.
•W hen two network interface cards or more are
installed on the PC in use, the network interface
card(s) not used for receiving images should be
invalidated...

27
Configure the camera settings such as image quality and brightness, etc.\
[Camera]
Click the [Camera] tab on the Camera setup page. (☞page 23)
The following are descriptions of how to configure the settings relating\
 to image quality and brightness, etc. Refer to
the operating instructions for further information about the setup items\
 (camera setup page). Refer to page 52 for
descriptions of how to operate the setup items (camera setup page).
Note:
The Camera setup page on the [Camera] tab can be...

28
Configure the settings relating to audio [Audio]
Click the [Audio] tab on the Camera setup page. (☞page 23)
The settings relating to audio can be configured on this page. 
[Mic mode*]
Select ON or OFF to determine whether to turn on or
off audio on a PC.
ON:Transmits audio from the camera to the PC. Audio
can be heard with images on the PC. Images and
audio will not be synchronized. 
OFF:Does not transmit audio from the camera to the
PC. Therefore, no settings and controls relating
audio will be...

29
Configures the multi-screen settings [Multi-screen setup]
The cameras to be used for the multi-screen display can be registered on\
 this page. 
Refer to page 9 for descriptions of how to display images on a multi-scr\
een.
Note:
The following cameras are available for the multi-screen display (as of\
 April 2006).
WV-NP1004, WV-NP244, WV-NP472, WV-NS324, WV-NW474S
[IP Address]
Enter the IP address or the host name of the camera to
be used for the multi-screen. 4 cameras can be regis-
tered as a group...

30
Configure the alarm settings [Alarm setup]
The settings relating to alarm occurrences such as settings for the alar\
m action at an alarm occurrence, the alarm
occurrence notification, and the VMD area settings can be configured on \
this page. 
The Alarm setup page has 3 tabs of the [Alarm] tab, the [VMD area] tab\
 and the [Notification] tab.
Configure the settings relating to the alarm action [Alarm]
Click the [Alarm] tab on the Alarm setup page.
The settings relating to the alarm action can be...