Panasonic Network Camera Server Bb Hcs301a Operating Instructions

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 121
2.25 Notifying Setup of an Alarm Log
Once a day, an alarm log sent at a specified time can be checked. To enable Alarm 
Log, set Alarm or Motion Detection for Trigger Setting and check [Enable].
1.Click [Alarm Log] on the Setup page.
2.Set each parameter.
3.Click [Save] to save the settings.
 Clicking [Cancel] cancels your settings without saving changes.
4.Click [Go to Alarm Log page].
 The Alarm Log page is displayed.
Note
If you change a setup of operation and click [Save], new alarm logs are 
deleted. 
						

							Operating Instructions
122
SettingDescription
A setup of operation Alarm log operation can be set here.
Time Set the date and time to send alarm logs via E-mail.
SMTP Server IP 
Address or Host 
Name
*1
*1But [Space], [], [], [&], [] are not available.
 If you set the server IP address, set 4 digits (0—255) 
and 3 periods such as 192.168.0.253. But 0.0.0.0 
and 255.255.255.255 are not available. Or set a host 
name (0—255 characters).
 An IPv6 address can be set.
Por t  N o. Enter a number (1—65535). Usually set to 25.
POP3 Server IP 
Address or Host 
Name
*1
 If you set the server IP address, set 4 digits (0—255) 
and 3 periods such as 192.168.0.253. But 0.0.0.0 
and 255.255.255.255 are not available. Or set a host 
name (0—255 characters).
 An IPv6 address can be set.
Por t  N o. Enter a number (1—65535). Usually set to 110.
Login ID*2
*2But [] is not available.
 If your ISP requires a login ID to log in to a POP3 
server, set it (0—63 characters).
Password*2 If your ISP requires a password to log in to a POP3 
server, set it (0—63 characters).
Reply E-mail 
Address*2 Set the senders E-mail address. We recommend you 
to set the administrators E-mail address.
Destination E-mail 
Address 1-3*2 Set the destination E-mail address (up to 3).
Subject*2 Enter a subject with ASCII characters (see page 163) 
or characters in each language (0—44 characters for a 
1-byte character and 0—22 characters for a 2-byte 
character). 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 123
2.26 Changing Initial Settings on the Single 
Camera page or the Multi-Camera page
The Image Display page allows you to change initial settings (display settings when 
a user accesses this product) of image resolution, image quality and refresh 
interval. You can display a time stamp on the image. The initial language can be 
selected from eight languages. The banner can be displayed for administrator or 
general users or both.
1.Click [Image Display] on the Setup page.
2.Set each parameter.
 Clicking [Cancel] cancels your settings without saving changes. 
						

							Operating Instructions
124
SettingDescription
Image Resolution Select the image resolution.
640 × 480 pixels (Only for the Single Camera page)
320 × 240 pixels (default)
160 × 120 pixels (Only for the Multi-Camera page)
Image Quality Select the image quality.
[Favor Clarity] optimizes for good quality.
[Standard] offers standard quality. (default)
[Favor Motion] optimizes for enhanced motion.
Refresh Interval Select a refresh interval. 
Motion, 3 s, 5 s, 10 s, 30 s, and 60 s
Time stamp setting You can display a time stamp on the upper left side of 
the image. Select from [Enable] or [Disable].
Notes
 If you enable this feature, the time is also stamped 
on the buffered image.
 Set AM/PM format and 24H format on the Date 
and Time page.
Language Select the initial language from English, French, 
German, Italian, Spanish, Russian, Simplified Chinese 
or Japanese. The selected language is displayed as 
the initial language on the Top, Single Camera, Multi-
Camera and Buffered Image pages. If you select 
English or Japanese, all pages can be changed. But if 
you select other language, the Setup, Maintenance and 
Support pages are displayed only in English.
Banner Display When this product accesses the Internet, the banner 
displays product information about this product or 
announcements about the latest firmware, etc. from 
Panasonic. Checking [Display] for Administrator is 
particularly recommended.
 When checked, the banner is displayed for 
administrator or general users or both.
 The banner is displayed only on the Single Camera 
page (see page 
16). 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 125
3.Click [Save] when finished.
 New settings are saved.
 When finished, Success! is displayed.
4.Click [Go to Image Display page].
 The Image Display page is displayed. 
						

							Operating Instructions
126
2.27 Configuring Multiple Images
To view images on the Multi-Camera page, this products or the Panasonic Network 
Cameras IP address and camera name must be configured on the Multi-Camera 
Setup page. These configurations are required to use the Multi-Camera page. Up 
to 12 cameras can be configured.
1.Click [Multi-Camera] on the Setup page.
2.Click Add.
Notes
 If you click the number, the modification page is displayed. The setting can 
be modified or deleted on it.
 If you configured multiple cameras, you can change the number. Select 
the number, and click [Move].
3.Set each parameter.
 Clicking [Cancel] cancels your settings without saving changes. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 127
Notes
 Set the local IP address and port number for this product on the same 
LAN.
 If this product is accessed from the Internet, be sure to use the global IP 
address. In this situation, local IP addresses such as 
192.168.
. cannot be used.
4.Click [Save] when finished.
 New settings are saved.
 The Multi-Camera Setup page is displayed.
SettingDescription
Display Check the box to enable the image display.
IP Address*1 or 
Host Name*2 Set the IP address or the host name to enable the image 
display.
Po r t N o. Set the port number (1—65535).
Camera Name*3 The name is displayed only on the Multi-Camera page.
*1In IPv4, set 4 digits (0—255) and 3 periods such as 192.168.0.253. But 
0.0.0.0 and 255.255.255.255 are not available.
In IPv6, set the host name.*2Enter ASCII characters for the host name (see page 163). But [Space], [], [], 
[#], [&], [%], [=], [+], [?], [] are not available.
Enter 1—255 characters.*3Enter ASCII characters (see page 163) or characters in each language (1—15 
characters for a 1-byte character and 1—7 characters for a 2-byte character). 
But [Space], [], [], [#], [&], [%], [=], [+], [?], [:], [] are not available. 
						

							Operating Instructions
128
2.28 Specifying Operation Time
The Operation Time page allows you to limit the operation time. The image turns 
to a gray screen outside the operation time.
Notes
 If you wrongly set the time period, your privacy may be seen. Confirm the 
time period after the setup.
 If you access this product as an administrator, you can view the image 
outside the time period.
1.Click [Operation Time] on the Setup page.
2.Click [No.] to set the operation time.
Note
If No. 1—7 are disabled, this product can always be operated.
3.Check [Enable], set the time. 
 Clicking [Cancel] takes you back to the previous page. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 129
4.Click [Save] when finished.
 New settings are saved.
 The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, this product can be operated on both Monday and Tuesday.
SettingDescription
Enable Check the box to enable the setting. Clear the box to 
disable it.
A day of the 
week Check the box to enable the day. Clear the box to disable it.
Operation Time Select the [Always] option when you do not specify the time 
period. If you specify the time period, select the time period 
option and set the time period. 
						

							Operating Instructions
130
2.29 Controlling External Output Terminal
The digital output terminal allows you to control the external devices. You can 
change the initial status of the output signal.
Note
Connect the external devices to this product.
1.Click [External Output] on the Setup page.
2.Click [Save] when finished.
 Clicking [Cancel] cancels your settings without saving changes.
 New settings are saved.
 When finished, Success! is displayed. 
3.Click [Go to External Output Control page].
 The External Output Control page is displayed.
SettingDescription
External Device 
Control Output If you check [Open], the internal transistor turns off and the 
external output terminal gets high impedance (open 
collector) when this product powers up. If you check [Short 
to GND], the internal transistor turns on and is electrically 
short-circuited to GND pin when this product powers up. 
The external output terminal gets low impedance (0 V). 
Button name 
modification You can change the output control button names on the 
operation bar. You can name the button depending on your 
external devices.