Panasonic Network Camera Server Bb Hcs301a Operating Instructions

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 111
8.After you confirm the settings and click [Next>], set E-mail notification and click 
[Next>].
 If you select [Enable], the E-mail Notification When Triggered page is 
displayed. Enter the settings seeing page 
109 and page 110.
9.Click [Save] after confirming the settings.
 New settings are saved.
 When finished, Success! is displayed.
Note
If you click [Save], all buffered images on the SD memory card are deleted.
SettingDescription
Disable This product does not send an E-mail notification when 
buffering or transferring image.
Enable This product sends an E-mail notification (up to 3 
destinations) when buffering or transferring image. 
						

							Operating Instructions
112
10.Click [Go to Trigger page].
 The Trigger page is displayed.
Notes
 If you set a short interval to transfer image to a cell phone, many E-mails 
may be sent to it leading to a large phone bill. Therefore, we recommend 
you to set a long interval. 1 image per minute frequency is recommended.
 Motion Detection transfer stops its operations until this product finishes all 
transfers. For example, if this product transfers 3 images per minute and 
6 images in total, the Motion Detection will be in the following operation.
 If you are buffering images on the internal memory, the following 
operations also delete all buffered images.
– Turning off this product.
– Saving the Date and Time page.
– Restarting, updating firmware or resetting this product to factory 
default. 
Detectable DetectableUndetectable
1st 2nd 3rd 4th 5th 6th120 seconds
A Motion Detection signal is detected. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 113
2.19 Formatting the SD memory card
You can record camera images to the SD memory card (customer-provided). 
Before you record the camera image, you need to format the SD memory card.
Note
 You can confirm the SD memory capacity on the Status page (see page 
133).
1.Insert the SD memory card (see page 165).
2.Click [Trigger] on the Setup page.
3.Click [Format].
4.Click [OK] on the confirmation window.
 Format is complete.
5.Click [Go to Trigger page].
 The Trigger page is displayed. 
						

							Operating Instructions
114
2.20 Stopping the SD Memory Recording
After you stop the SD memory recording, remove the SD memory card.
Notes
 You can confirm the SD memory capacity on the Status page (see page 
133).
 If this product is restarted (see page 134), the SD memory recording 
starts again.
 If you remove the SD memory card and insert it again (see page 165), the 
SD memory recording starts again.
1.Click [Trigger] on the Setup page.
2.Click [SD video recording stop].
3.Click [OK] on the confirmation window.
 The SD memory recording is stopped.
4.Click [Go to Trigger page].
 The Trigger page is displayed.
Note
Ensure that recording has stopped before removing the SD memory card. 
(See page 
114) Do not remove the SD memory card, nor restart or turn off this 
product while recording images on the card. Doing so can cause a decrease 
in SD memory card capacity, data corruption or camera malfunction. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 115
2.21 Starting the SD Memory Recording
The SD memory recording can be started on the Trigger page.
Notes
 You can confirm the SD memory capacity on the Status page (see page 
133).
 If this product is restarted (see page 134), the SD memory recording 
starts again.
 If you remove the SD memory card and insert it again (see page 165), the 
SD memory recording starts again.
1.Click [Trigger] on the Setup page.
2.Click [SD video recording start].
 SD video recording was started. is displayed.
3.Click [Go to Trigger page].
 The Trigger page is displayed.
Note
Ensure that recording has stopped before removing the SD memory card. 
(See page 
114) Do not remove the SD memory card, nor restart or turn off this 
product while recording images on the card. Doing so can cause a decrease 
in SD memory card capacity, data corruption or camera malfunction. 
						

							Operating Instructions
116
2.22 Transfer the Image in Transport Mode
This product can transfer the image in transport mode by E-mail or FTP.
Prepare the following requirements.
See page 48 and set up the E-mail or FTP server.
ItemSupported Feature
E-mail or FTP 
ServerOperating 
System:IPsec supported
ISP Service:Services for multiple static global 
addresses (A global address must be set 
up to the server.)
Camera ServerISP Service :Services for multiple static global 
addresses (A global address must be set 
up to this product.)
Transport Mode
Encrypted E-mail or FTP 
Server
I
ND
C
 
I
NI
NI
NA
U
D
I
OUD
IOV
I
D
E
OVIDEOP
OPOW
E
RWE
R 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 117
2.23 Transfer the Image in Tunnel Mode
This product can transfer the image in tunnel mode by E-mail or FTP.
Prepare the following requirements.
See page 51 and set up the E-mail or FTP server.
ItemSupported Feature
VPN RouterISP Service 
(in IPv4) 
:Services for static global addresses (A 
global address must be set up to the WAN 
side.)
ISP Service 
(in IPv6)
:IPv4/IPv6 Dual-Stack or IPv6 over IPv4 
Tunneling service
Camera ServerISP Service 
(in IPv4) 
:Services for multiple static global 
addresses (A global address must be set 
up to this product.)
ISP Service 
(in IPv6)
:IPv4/IPv6 Dual-Stack or IPv6 over IPv4 
Tunneling service
Encrypted
Not EncryptedTunnel Mode VPN Router
WA N
LAN
E-mail or FTPServer E-mail or FTP
Server
I
ND
C
 
I
NI
NI
NAU
D
IOUD
IOV
I
D
E
OVIDEOP
OPOW
E
RWER 
						

							Operating Instructions
118
2.24 Setting the Motion Detection
The Motion Detection page allows you to adjust sensitivity of the Motion Detection. 
Threshold: If the threshold is set low, this function sensitively detects changes.
Sensitivity: If you set sensitivity high, amplitude on the motion detection bar gets 
jumpy.
1.Click [Motion Detection] on the Setup page.
2.Click the Motion Detection bar in Threshold to set the threshold level.
3.Click the Motion Detection bar in Sensitivity to set the sensitivity level.
4.Click [Save] to save the settings.
 Clicking [Cancel] cancels your settings without saving changes.
5.Click [Go to Motion Detection page].
 The Motion Detection page is displayed.
SettingDescription
Threshold Adjust the threshold for Motion Detection. Setting the 
threshold lower allows subtler changes to be detected.
Sensitivity  If you set sensitivity high, amplitude on the motion 
detection bar gets jumpy. 
						

							Operating Instructions
[For assistance, please call: 1-800-272-7033] 119
Preview
The preview window displays current threshold and detection level.
 The threshold is displayed by between green and red bar.
 The detection level is displayed by between dark and light color.
Note
Setting Threshold and Sensitivity is enabled after saving, and reflect to 
preview. 
What is the motion detection?
We assume no responsibility whatsoever for any damages resulting from the use 
of the motion detection feature. We do not recommend the use of the motion 
detection function for supervisional purposes where high reliability is essential. 
The motion detection function is not suitable for this kind of usage.
What is the threshold?
The threshold is a value for this product to detect motions on the image during 
the motion detection buffering. Setting the threshold lower allows subtler 
changes to be detected. Setting the threshold higher allows bigger changes 
that might occupy half the image to be detected.
Threshold 
						

							Operating Instructions
120
What is the sensitivity?
The sensitivity is the brightness change level for this product to detect as the motion. The 
high sensitivity setting enables this product to detect the slight brightness change. Lower the 
sensitivity to make this product to detect only the big brightness change.
Note
Lowering the threshold and heightening sensitivity enable this product easily 
to detect the trivial motion on the part of the image.
Notes
 The motion detection is activated by object outlines changes and the brightness 
changes. This feature is designed to alleviate false detections due to overall 
brightness changes caused by sunlight. But in this case, this product may falsely 
detect the rapid brightness changes by the artificial light such as the fluorescent 
light. In other cases, motion detection of Panasonic Network Camera Recorder 
detects whole objects and brightness changes. The way to detect motion differs 
between this product and Network Camera Recorder. Additionally, if the objects 
color is absorbed by the background color, this product is hard to detect the 
motions.
 The detecting level depends on the object, resolution, or image quality. Confirm 
the condition on the Preview window with following the above procedure when 
setting the Motion Detection.
Detect motions 
according to the 
threshold.When the level exceeds 
the threshold, this product 
detects motions.