Panasonic Network Camera Kx Hcm280a Installation Troubleshooting Information Manual

							Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 11
1.3.2 Rear View
1.3.3 Bottom View
Ethernet (LAN) port
(See page 12)
Analog Video Output
(See page 14)
External I/O
(See page 119 of the 
Operating 
Instructions on the 
Setup CD-ROM)
DC IN jack
(See page 13)
Hook for AC adaptor 
cord
(See page 13)
FAC TO RY  D E FAU LT
RESET button
(See page 121 of the
Operating Instructions on
the Setup CD-ROM)
Hole for Ceiling Plate A
(See page 35)
MAC Address and Serial 
Number are indicated on 
the label.
kxhcm280ait.book  11 ページ  ２００５年３月９日　水曜日　午後１時２３分 
						

							Installation/Troubleshooting
12
1.4 Connecting the Camera to Your Router
Connect the camera to your router with an Ethernet cable to set up the camera.
1.Connect the Ethernet cable (customer-provided) to the camera.
Note
These instructions assume your PC is already connected to the Internet and 
your network includes a router.
2.Connect the Ethernet cable to your router.
Ethernet port
Ethernet cable
To your router
LAN ports WAN port
To the outlet
To the camera
To your PCTo your modem
Ethernet cable (Straight Cat5 cable)
(Customer-provided)
kxhcm280ait.book  12 ページ  ２００５年３月９日　水曜日　午後１時２３分 
						

							Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 13
3.Connect the AC adaptor cord to the DC In jack, and plug the AC cord into the 
outlet.
 The AC cord is used as the main disconnect device, ensure that the 
socket-outlet is located/installed near the equipment and is easily 
accessible.
 Use only specified Panasonic AC adaptor PSLP1242 (Order No. 
PSLP1242Y).
 If the indicator does not light green, see page 39.
 A noise can be heard during pan/tilt operation. This is normal.
4.Hook the AC adaptor cord to the Hook for AC adaptor cord.
AC cord AC adaptorPower Outlet
Hook for AC adaptor cord
DC IN jack
kxhcm280ait.book  13 ページ  ２００５年３月９日　水曜日　午後１時２３分 
						

							Installation/Troubleshooting
14
1.5 Connecting the Camera to Your TV
You can view camera images on a TV or record them using a video recording 
device (VCR, DVD recorder, etc.).
Note
 When the camera is in color night view mode, images may not be 
displayed correctly on the TV.
Analog composite (NTSC)
video output terminal
(  3.5 mm plug 1Vp-p, 75Ω)
Video cable (not included)
To video input terminal
kxhcm280ait.book  14 ページ  ２００５年３月９日　水曜日　午後１時２３分 
						

							Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 15
1.6 Setting up the Camera to View on the LAN
Setup CD-ROM allows you to easily set up the camera.
Note
 To avoid any possible problems, temporarily disable any firewall or 
antivirus software.
 This procedure explains installation of the camera on the same network 
that your PC is part of.
 Before proceeding, close your web browser.
 See page 132 of the Operating Instructions on the Setup CD-ROM for 
details.
1.Insert the Setup CD-ROM into the CD-ROM drive of the PC.
 The window is automatically displayed. 
(If the Network Camera Setup window is not displayed automatically, 
double-click Setup.exe file on the Setup CD-ROM.)
2.Click [Camera Setup].
 When the following dialog is displayed, click [Unblock].
Displays version information 
about this program.
Sets up the camera.
Displays the camera manuals. 
If your PC does not have Adobe® 
Acrobat® Reader®, install it from 
the Adobe Reader website.
Installs Network Camera 
Recorder trial version.
Closes the Setup Program.
kxhcm280ait.book  15 ページ  ２００５年３月９日　水曜日　午後１時２３分 
						

							Installation/Troubleshooting
16
3.Select the camera to set up and click [Execute].
 This program searches for the cameras that are connected to the router 
and displays the MAC Addresses, IP addresses and Port Numbers.
 The MAC Address (see page 11) on the bottom of the camera shows 
which camera you select on the Camera List window.
Note
 If more than 20 minutes have passed since the camera was turned on, the 
camera cannot be set up from the Setup Program. In this situation, 
disconnect the AC cord from the outlet, and reconnect it again.
 The Setup Program may not list any cameras due to your firewall or 
antivirus software settings on your PC. If you cannot disable your firewall 
or antivirus software, you can set up the camera entering the camera MAC 
address on the following window. The cameras MAC address can be 
found on the label affixed to each camera. See page 27 for details.
Camera 
Status
Camera 
List window
Displays IPv4 or 
IPv6 information. Por t 
No. MAC 
Address
IP 
Address
kxhcm280ait.book  16 ページ  ２００５年３月９日　水曜日　午後１時２３分 
						

							Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 17
4.Click [Automatic Setup (Local Access Only)].
 For the first time installation or after pressing the FACTORY DEFAULT 
RESET button, only [Automatic Setup (Local Access Only)] can be 
selected. To set up the camera with Static or DHCP settings, after 
performing the [Automatic Setup (Local Access Only)], run the Setup 
Program again and select [Manual Setup].
5.Enter the user name and password you wish to use, and click [Save].
6.Enter the name and password that were entered above, and click [OK].
kxhcm280ait.book  17 ページ  ２００５年３月９日　水曜日　午後１時２３分 
						

							Installation/Troubleshooting
18
7.When the Single Camera page is displayed, the setup is completed.
 When Security Warning window is displayed, click [Yes]. (See page 32)
 See page 33 for Security Warning window when using Microsoft Windows 
XP Service Pack 2.
Note
To insure that the most current image is displayed, Internet Explorer should be 
configured as follows. This will not have any negative result on normal use.
To enable Internet access to the camera
Click [Next] to set up the Internet access to the camera and go to step 3 on page 
20.
 If you do not allow the Internet access, click [Cancel], and go to page 30 
to confirm the camera image.
1.While viewing any website, Click [Tools][Internet Options].
2.In the section Temporary Internet Files, click [Settings] and check 
[Every visit to the page].
Network Camera
ZoomFocusProgram PresetScan
Pan / Tilt
640X480320X240∗Resolution
STD -+ BrightnessOpenShortOutput
Refresh Interval
Image Quality
Favor ClarityFavor MotionStandard∗
Motion
Please click here when gray color screen displayed
Running in IPv4 mode.Alarm
kxhcm280ait.book  18 ページ  ２００５年３月９日　水曜日　午後１時２３分 
						

							Installation/Troubleshooting
[For assistance, please call: 1-800-272-7033]                                 19
1.7 Setting up Internet Access to the Camera
1.Display the Camera List window (see page 15).
2.Select the camera to set up and click [Execute].
 This program searches for the cameras that are connected to the router 
and displays the MAC Addresses, IP addresses and Port Numbers.
 The MAC Address (see page 11) on the bottom of the camera shows 
which camera you select on the Camera List window.
Note
If more than 20 minutes have passed since the camera was turned on, the 
camera cannot be set up from the Setup Program. In this situation, restart the 
camera.
Camera 
Status
Camera 
List window
Displays IPv4 or 
IPv6 information. Por t 
No. MAC 
Address
IP 
Address
kxhcm280ait.book  19 ページ  ２００５年３月９日　水曜日　午後１時２３分 
						

							Installation/Troubleshooting
20
3.Click [Automatic Setup (Internet Access)].
Note
In order for Internet access to be properly enabled, your routers UPnP™ 
feature should be enabled. Most router manufacturers disable this feature. See 
http://panasonic.co.jp/pcc/products/en/netwkcam/ for more information. 
4.Enter the user name and password that were set, and click [OK].
5.If your router supports UPnP™, select [Enable], otherwise select [Disable]. 
Then click [Next].
 If you select [Disable], skip to step 9.
Sets up the camera to view on 
the LAN.
Sets up the Internet access to 
the camera.
Manually sets up the camera.
Disables IPsec. If disabled, the 
button is displayed gray.
Displays the Setup page (see 
page 37 of the Operating 
Instructions on the Setup CD-
ROM).
kxhcm280ait.book  20 ページ  ２００５年３月９日　水曜日　午後１時２３分