Panasonic Network Camera Kx Hcm250 Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033] 91
3.5.14 Update Firmware
Update Firmware windowallows the user to install the latest version of the
Network Camera internal operating system. In most cases, this will never be
necessary. Changes may be necessary to accommodate new operating systems
or new web browsers that are not shown on page 10. In those cases, Update
Firmware would be available from the Network Camera Technical Support Site at
http://panasonic.co.jp/pcc/en/. Check...

Operating Instructions
92
4.Click[Update Firmware]on Setup Page.
5.Click[Update Firmware].
Wait about one minute.
Note
If you click[Update Firmware], operation cannot be canceled. If canceled,
refertopage120. 

Operating Instructions
[For assistance, please call: 1-800-272-7033] 93
6.Click[Browse...]to select the firmware from the file selector.
 A Dialog box appears to choose the file.
7.Select a desired Firmware file (including the path information) and click
[Open].
8.Make sure the desired firmware file name is selected correctly, and click
[Update Firmware].
Restarting window is displayed, and Network Camera restarts
automatically.
Restart operation takes about one minute.
Confirm that the Update Firmware...

Operating Instructions
94
3.5.15 Reset to Factory Default
Reset to Factory Default windowinitializes all the parameters including the ID,
Password, IP address and Subnet Mask except Date and Time setting to the
factory default. Reconfirm the settings before doing the Reset to Factory Default
operation.
1.Click[Reset to Factory Default]on Setup Page.
2.Click[Execute].
 Indicator changes such asOrange blinking twice–>Tu r n i n g o f f
about 15 seconds. Initializing takes about one minute....

Operating Instructions
[For assistance, please call: 1-800-272-7033] 95
Section4
Technical Guides 

Operating Instructions
96
4.1 Network Camera Installation
High performance for wireless communication
Radio waves from the antenna of Network Camera transmit images. The
performance of wireless communication will change under the condition where
you install Network Camera and wireless router.Wireless windowon page 32
displays the data communication and signal strength status of the wireless
network.
Notes
 Install Network Camera away from electrical appliances such as TVs or
cordless telephones.
 Metal...

Operating Instructions
[For assistance, please call: 1-800-272-7033] 97
4.1.1 Network Camera Mounting
Four mounting methods are shown in the following figures. Confirm that the AC
adaptor cord is threaded through the hook, and the direction of the top and bottom
of Network Camera before mounting. Ask the authorized dealer for the mounting.
Check wireless communication status onWireless windowon page 32 before
mounting Network Camera.
Note
Mounting and cabling instructions described in this Operating...

Operating Instructions
98
Notes
 Network Camera is intended for indoor use only. Prolonged exposure
to direct sunlight or halogen light may damage the CMOS sensor.
 Make sure the Indicator is always in the upper right corner when you
mount.
CAUTION
Drive mounting screws into the wall. Be careful to avoid touching any
metalwork (metal/wire laths etc.), conduits or electrical cables buried in the
wall.
top
bottom
top
top
bottom
bottom
Ceiling Mounting
Wall MountingFlexible Stand Mounting
top
bottom 

Operating Instructions
[For assistance, please call: 1-800-272-7033] 99
Flexible Stand Mounting
Tripod Mounting
Attach Network Camera to the tripod by using the tripod bolt. 1) Attach Network Camera by screwing the threaded mount into the tripod
mounting hole.
2) TurnthegriptofixtheFlexibleStandfirmly.
1)
2)
Tripod
mounting
hole
Tripod
mounting
hole 

Operating Instructions
100
Wall Mounting
1) Mount the Flexible Stand firmly to the wall or the beam using the three
screws (accessories). Set the Flexible Stand 240 mm (9.5 inches) away
from the ceiling.
 Use proper screws fit for the material of the wall.
2) Attach Network Camera by screwing the threaded mount into the tripod
mounting hole. Mounting hole on the rear side is also available.
3) Adjust the position of Network Camera and secure the Flexible Stand
firmly.
4) Roll up the cables and Flexible...