Panasonic Network Camera BL-C30C Operating Instructions

Operating Instructions
81
2.15 Specifying Operation Time
The Operation Time page allows you to limit the operation time. The camera image 
turns to a gray screen outside the operation time.
Notes
 If you wrongly set the time period, your privacy may be seen. Confirm the 
time period after the setup.
 If you access the camera as an administrator, you can view the image 
outside the time period.
1.Click [Operation Time] on the Setup page.
2.Click No. to set the operation time.
Note
If No. 1—7 are...

Operating Instructions
82
4.Click [Save] when finished.
 New settings are saved.
 The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, the camera can be operated on both Monday and Tuesday.
Operation Time Select the [Always] option when you do not specify the time 
period. If you want to specify the time period,...

Operating Instructions
83
2.16 Changing Indicator Display
The Indicator Control page allows you to select Indicator operation. Indicator has 
four options.
Always on.
 Turn the indicator on when the camera is accessed.
 Turn the indicator on during sensor reaction.
Always off.
1.Click [Indicator Control] on the Setup page.
2.Select indicator option.
 Clicking [Cancel] cancels your settings without saving changes.
Notes
 See page 8 in the Installation/Troubleshooting guide for indicator 
display.
...

Operating Instructions
84
2.17 Enabling Privacy Mode
Pressing the privacy button turns the camera into privacy mode. You can keep your 
privacy in privacy mode. In this case, the camera operation stops, and the image 
transfer by timer or sensor (see page 
60 or page 69) is also stopped. The indicator 
turns red, and viewers see a gray screen. Privacy mode can be controlled from a 
cell phone (see page 
27) or a PC.
1.Click [Privacy Mode] on the Setup page.
2.Click [Save] when finished.
 Selecting...

Operating Instructions
85
3 Camera Maintenance
3.1 Maintenance page
Maintenance
(1)StatusDisplays the camera settings and status (see page 86).
(2)Wireless StatusDisplays wireless information (see page 86).
(3)RestartRestarts the camera (see page 87).
(4)Update FirmwareUpdates the camera firmware (see page 88).
(5)Save SettingsCreates a configuration file (see page 91).
(6)Load SettingsLoads settings from a configuration file (see page 92).
(7)Reset to Factory 
DefaultResets the camera to its default...

Operating Instructions
86
3.1.1 Confirming the Status
The Status page allows you to check the status of the camera. The status 
information provides support for troubleshooting.
Clicking [Status] displays the following page.
Note
See Panasonic Network Camera support website at http://panasonic.co.jp/
pcc/products/en/netwkcam/ for details about status information.
3.1.2 Confirming the Wireless Status
The Wireless Status page allows you to check the wireless information. The 
wireless status information...

Operating Instructions
87
3.1.3 Restarting the Camera
The camera restarts by disconnecting the plug of the AC cord from the outlet and 
reconnecting it again. The camera can also be restarted on the Restart page. 
Note
When the camera restarts, the buffered images will be deleted.
1.Click [Restart] on the Maintenance page.
2.Click [Restar t].
 Restarting takes about 90 seconds. The Top page is displayed when 
finished. 

Operating Instructions
88
3.1.4 Updating the Camera Firmware
The Update Firmware page allows you to update the camera firmware. If the new 
firmware is available, install it into the camera.
Notes
 Do not turn off the power during firmware update.
 All buffered images will be deleted after the firmware update.
 The firmware version is displayed on the Top page and the Status page. 
1.Download the new firmware on the Panasonic Network Camera support 
website at...

Operating Instructions
89
 The Update page is displayed in about 90 seconds.
4.Click [Browse...].
 A dialog box is displayed to select the firmware.
5.Select the firmware (including directory information) and click [Open].
 The firmware file name is displayed.
6.Confirm the firmware file name, and click [Update Firmware].
 Clicking [Cancel] takes you back to the Top page without firmware update.
 The next message is displayed during update.
 The camera restarts automatically after update.
 The Top...

Operating Instructions
90
7.Confirm that the version number on the Top page is updated.
 If the version number is updated, the firmware update is complete.
Updated version