Panasonic Network Camera Bl C30a Operating Instructions

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 71
When you set [E-mail] for Transfer Method
Select [E-mail], and click [Next>]. The following page is displayed.
 Clicking [

Operating Instructions
72
9.After you confirm the settings and click [Next>], set E-mail notification and click 
[Next>].
 If you select [Enable], the E-mail Notification When Triggered page is 
displayed. Enter the settings seeing page 71 and page 72. When finished, 
click [Next>] and go to step 10.
10.Click [Save] after confirming the settings.
 New settings are saved. The buffered images are deleted.
 When finished, Success! is displayed. Subject  Enter a subject with ASCII characters (see page...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 73
11.Click [Go to Image Buffer/Transfer page].
 The Image Buffer/Transfer page is displayed.
Notes
 If you set a short interval to transfer image to a mobile phone, many E-
mails may be sent to it leading to a large phone bill. Therefore, we 
recommend you to set a long interval. In an emergency situation, the E-
mail transfer can be stopped by enabling privacy mode using a mobile 
phone (see page...

Operating Instructions
74
2.15 Specifying Operation Time
The Operation Time page allows you to limit the operation time. The camera image 
turns to a gray screen outside the operation time.
1.Click [Operation Time] on the Setup page.
2.Click [No.] to set the operation time.
Note
If No. 1—7 are disabled, the camera can always be operated.
3.Check [Enable], set the time, and click [Save] 
 Clicking [Cancel] takes you back to the previous page without saving 
changes.
Setting Description
Enable  Check the...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 75
4.Click [Save] when finished.
 New settings are saved.
 The Operation Time page is displayed.
About Operation Time
In the operation time settings, the enabled settings take priority over the disabled 
settings. Therefore, if Monday or Tuesday is disabled in a setting but enabled in 
other settings, the camera can be operated on both Monday and Tuesday. 

Operating Instructions
76
2.16 Changing Indicator Display
The Indicator Control page allows you to select Indicator operation. Indicator has 
four options.
Always on
 Turn the indicator on when the camera is accessed.
 Turn the indicator on during sensor reaction.
Always off
1.Click [Indicator Control] on the Setup page.
2.Select indicator option.
 Clicking [Cancel] cancels your settings without saving changes.
Notes
 See page 7 in the Installation/Troubleshooting for indicator display.
 Selecting...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 77
2.17 Enabling Privacy Mode
Pressing the privacy button turns the camera into privacy mode. You can keep your 
privacy in privacy mode. In this case, the camera operation stops, and the image 
transfer by timer or sensor (see page 57 or page 64) is also stopped. The indicator 
turns red, and viewers see a gray screen. Privacy mode can be controlled from a 
mobile phone (see page 25) or a PC.
1.Click...

Operating Instructions
78
3 Camera Maintenance
3.1 Maintenance page
Maintenance
(15) StatusDisplays the camera settings and status (see page 79).
(16) Wireless StatusDisplays wireless information (see page 79).
(17) RestartRestarts the camera (see page 80).
(18) Update FirmwareUpdates the camera firmware (see page 81).
(19) Save SettingsCreates a configuration file (see page 84).
(20) Load SettingsLoads settings from a configuration file (see page 85).
(21) Reset to Factory 
DefaultResets the camera to...

Operating Instructions
[For assistance, please call: 1-800-272-7033]                                 79
3.1.1 Confirming the Status
The Status page allows you to check the status of the camera. The status 
information provides support for troubleshooting.
Clicking [Status] displays the following page.
Note
See Panasonic Network Camera support website at http://panasonic.co.jp/
pcc/products/en/netwkcam/ for details about status information.
3.1.2 Confirming the Wireless Status
The Wireless Status page...

Operating Instructions
80
3.1.3 Restarting the Camera
The camera restarts by disconnecting the plug of the AC cord from the outlet and 
reconnecting it again. The camera can also be restarted on the Restart page. 
Note
When the camera restarts, the buffered images will be deleted.
1.Click [Restart] on the Maintenance page.
2.Click [Restart].
 Restarting takes about 90 seconds. The Top page is displayed when 
finished.